Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for dye DM5
Summary of Contents for dye DM5
- Page 1 ™ ™...
- Page 2 < < S P E C S > > W E I G H T [ 2 . 1 5 L B S ] W I D T H [ 1 . 2 5 ” ] L E N G T H [ 9 ”...
-
Page 3: Table Of Contents
TA B L E O F C O N TEN TS QUICK REFERENCE ........................PAGE 02 IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES . -
Page 4: Quick Reference
Turning the adjustment screw counterclockwise, or out, will raise the output pressure, increasing the velocity. NOTE: If the battery is too low, it may not be able to power the solenoid correctly. This will affect your DM5’s velocity, causing it... -
Page 5: Important Safety Instructions And Guidelines
• Never look into the barrel or breech area of the DM5 when the marker is switched on and able to fire. • Always fit a barrel blocking device to your DM5 when not in use on the field of play. -
Page 6: Board Settings And Functions
FIRING THE DM5 As soon as the marker is turned on and the LED turns from blue to either red or green, the DM5 is ready to fire. If there is no ball and the LED is RED, you need to hold the trigger for 1 second to force the DM5 to fire once. If there is a paintball inside the breech and the LED is green, just press the trigger to fire the marker. - Page 7 DM5 BOARD - Settings and Functions (continued) BOARD SETTINGS AND CONFIGURATION MODE There are five settings you can alter on the DM5 board with the DIP switches inside the grip frame (see figure 2) Anti Bolt Stick. Eye Sensitivity This setting changes how long the eye waits for the ball to set into the breech.
- Page 8 Dwell is the amount of time that the solenoid will be activated. Follow these steps for the best way to set your dwell: • Remove loader and any paintballs from the DM5 marker. • With the dwell set at 12, start increasing the value until the marker begins to fire.
- Page 9 BATTERY NEEDS TO BE CHANGED. An intermittent blinking blue power the solenoid correctly. This will light indicates a low battery. A affect the DM5’s velocity, causing it to become inconsistent and/or low. low battery may cause malfunctions to the marker. In this case, the battery should be changed as soon as possible.
-
Page 10: Fuse Bolt
BACK POSITION When the DM5 is aired up, air is transferred by the solenoid to the front of the cylinder. This air pushes against the bolt sail and the bolt is held in the back position. When the bolt is held back, the 013 o-ring in the top hat seals around the bolt and contains the air in the supply chamber. - Page 11 BEFORE INSTALLING THE BOLT INTO THE MARKER, BE SURE ALL BOLT SLEEVE COMPONENTS ARE SCREWED TOGETHER SNUGLY. If you do not grease the Fuse bolt, you will run the risk of damaging o-rings. This will create excessive friction and drag on the bolt, ultimately resulting in breaking the bolt. When greasing the DM5 Fuse bolt, pay special attention to all o-rings that are on the bolt and that ride on a surface of the bolt.
-
Page 12: Low Pressure Regulator (Lpr)
This pressure is used to move the bolt forward and back. The factory setting is 75 PSI. You can fine tune your DM5 to its minimum cycle pressure. This will reduce the amount of force of the bolt hitting the ball (reducing ball breaks) and help with efficiency. -
Page 13: On/Off Valve
ON/OFF VALVE - Maintenance and Changing O-rings ON/OFF: USAGE AND CHANGING O-RINGS The On/Off knob is located under the barrel in the front of the DM5 . Using the on/off is simple. To turn the (see figure 2) gas off, turn the knob so that is is facing sideways. If you had gas inside the marker, it will bleed out. To turn the gas on, turn the knob so that it faces vertically. -
Page 14: Hyper
Clean any accumulated dirt out of the air chambers and passages. failure of the regulator and possible Keep the piston o-rings and spring pack generously greased to allow smooth velocity adjustment and prevent damage to the DM5. erratic velocity spikes and drop off. • Excessive dirt and debris can affect Clean off all old grease that may be contaminated with dirt;... -
Page 15: Anti Chop Eyes/ Ball Detents
ANTI CHOP EYES The Anti Chop Eye (ACE) system will prevent the DM5 from chopping paint by not allowing the marker to fire until a ball is fully seated in front of the bolt. The eyes use a beam across the breech. On one side there is a transmitter, and on the opposite side a receiver. -
Page 16: Trigger Adjustment
TRIGGER ADJUSTMENT ADJUSTING YOUR TRIGGER The trigger’s forward travel and over travel are fully adjustable so that the user can fine-tune the trigger to his or her exact liking. You do not need to remove the frame from the gun in order to adjust the trigger pull. •... -
Page 17: Exploded View
DM5 EXPLODED VIEW P A R T S L I S T Adjustable Feed Neck On/Off Knob Ball Detent Eye Cover (o-ring 014) ASA Screw Hyper “ACE” Eye On/Off Set Screw 10 Solenoid 11 Front Frame Screw 12 45 Frame... -
Page 18: Trouble Shooting Guide
MARKER ISN'T WORKING THOUGH EYES ARE CLEAN AND ALL WIRES ARE CONNECTED; Bad seals in the bolt: take out the bolt, clean it, lube it with Dye Slick Lube™. Replace any o-rings that seem MARKER DOES WORK IF EYES ARE TURNED OFF damaged, swollen or in otherwise bad shape. -
Page 19: Warranty Information
Modification to the product will void the warranty. The only authorized lubricant for the marker is Slick Lube™. Use of any other lubricant will void your warranty. This warranty is limited to repair or replacement of defective parts with the customer to pay shipping costs. Warranty card and proof of purchase must be submitted to Dye Precision for warranty to be in effect. This warranty is not transferable. - Page 20 P 858-536-5183 F 858-536-5191 ©2004 DYE Precision, Inc. The stylized “dye” logo, the “Sphere” logo, the “DM5” logo, FUSE bolt and Hyper II are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc. Covered by one or more of the following U.S. Patents: 5,613,483; 5,881,707; 5,967,133; 6,035,843 and 6,474,326.
Need help?
Do you have a question about the DM5 and is the answer not in the manual?
Questions and answers