Behringer Europower PMP1000 User Manual
Power mixer
Hide thumbs
Also See for Europower PMP1000:
- Quick start manual (13 pages) ,
- User manual (25 pages) ,
- Quick start manual (41 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Behringer Europower PMP1000
Summary of Contents for Behringer Europower PMP1000
- Page 1 User Manual Version 1.0 November 2006...
-
Page 2: Important Safety Instructions
EUROPOWER PMP1000/PMP3000/PMP5000 IMPORTANT SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. -
Page 3: Table Of Contents
It is our philosophy to share our joy with you, because you are the most important member of the BEHRINGER team. With your highly competent suggestions for new products you’ve greatly contributed to shaping our company and making it successful. -
Page 4: Introduction
XENYX Mic Preamps give you crystal-clear audio free of noise and distortion when using microphones. BEHRINGER is a company with its roots in professional recording studio technology. For many years we have been successful in developing products for studio and live use. These include microphones and 19"... -
Page 5: Control Elements
(XLR connector) which provides +48 V phantom power for condenser microphones at the touch of a button (see rear panel). PMP1000: The two stereo channels 5/6 and 7/8 have an additional balanced XLR microphone input with +48 V phantom power. -
Page 6: Equalizer And Fbq
The upper LIM LED illuminates when the internal amp protection circuit responds to levels that are too high. PMP1000: The POWER LED is illuminated when you switch the unit on. The LIM LEDs and the LED display do NOT light up... -
Page 7: Effects Section
PMP3000/PMP5000: MON 1/2 fader. These faders are used to set the monitor output volume (see also PMP1000: The main mix allows you to control the volume from the Main 1 output with both faders. PMP3000/PMP5000: The MAIN 1 fader controls the volume of the EUROPOWER. -
Page 8: Connectors
CD/TAPE input signal to zero! PMP1000: The MAIN OUT jacks allow you to send the main line level signal to an external amplifier, when, for example, you want to use the mixer and effects section. The PMP3000... -
Page 9: Installation
AC power cord. 4.2 Audio connections The inputs and outputs of your BEHRINGER EUROPOWER are unbalanced 1/4" mono jacks—except for the mono channel line inputs, which are balanced 1/4" stereo jacks. Of course, all inputs and outputs work with both balanced and unbalanced connectors. -
Page 10: Loudspeaker Connections
EUROPOWER PMP1000/PMP3000/PMP5000 4.3 Loudspeaker connections Your power mixer is equipped with high-quality loudspeaker connectors (compatible to Neutrik ® Speakon safe and trouble-free operation. The Speakon especially developed for high-power loudspeakers. Once it is plugged in, it safely locks into position and cannot be accidentally disengaged. -
Page 11: Wiring & Connections
OUTPUT B. For a bridged mono operation to OUTPUT B, the AMP MODE selector switch its lower position “BRIDGE”. A separate stereo power amp (BEHRINGER EUROPOWER EP1500) connected to the preamp main outputs delivers the stereo main signal. Two active monitor must be set speakers for on-stage operation are connected to the preamp monitor output. - Page 12 For a dual mono operation, the AMP MODE switch be set to its center position (MON1/MONO for PMP3000/PMP5000 or MON for PMP1000)! The two loudspeaker outputs provide the main and the monitor signals, separately from each another. Each of these signals is then sent to two speakers wired in parallel.
-
Page 13: Expanded Set-Up
EUROPOWER PMP1000/PMP3000/PMP5000 Fig. 5.5: Expanded set-up This application is an expanded set-up based on the standard set-up as shown in fig. 5.4, and provides additional connection options. Again, this is just an example, which can be expanded in various ways. -
Page 14: Specifications
EUROPOWER PMP1000/PMP3000/PMP5000 MICROPHONE INPUTS Type Mic E.I.N. (20 Hz - 20 kHz) @ 0 Ω source resistance @ 50 Ω source resistance @ 150 Ω source resistance Frequency response Gain Max. input level Impedance Signal-to-noise ratio Distortion (THD+N) MONO LINE INPUTS... - Page 15 Weight BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
-
Page 16: Warranty
Colours and specification may vary slightly from product. Products are sold through our authorised dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER International GmbH. -
Page 17: Federal Communications Commission Compliance Information
(2) this device must accept any interference received, including interference that may cause undesired operation. Important information: Changes or modifications to the equipment not expressly approved by BEHRINGER USA can void the user’s authority to use the equipment. +1 425 673 7647...
Need help?
Do you have a question about the Europower PMP1000 and is the answer not in the manual?
Questions and answers
How do I get to check the fan
The provided context does not contain specific instructions on checking the fan on a Behringer Europower PMP1000. However, it mentions ensuring enough air space around the unit for cooling and avoiding overheating. It also states that blown fuses must be replaced with the same type and rating. For checking the fan, ensure the unit is powered on and listen for fan noise or feel for airflow. If there are concerns, consult a qualified service technician.
This answer is automatically generated