Sealey MK66.V4 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
Ensure the dispenser is on a reasonably flat, level floor before loading.

Ensure that all fittings are tight and secure.

Be aware that the paper cutting blades are sharp, handle with care.

DO NOT use the dispenser for any purpose other than that for which it is designed.

2. ASSEMBLY
Numbers in BOLD refer to the diagram in Fig.1
2.1 To assemble the side frames compress the silver latch
button at the top of the front frame 1 and insert the tube
into the back frame tube 1A until they snap together.
2.2 Onto each end of the two paper bars 20 slide a paper
holding ring 5 followed by a washer 16, holding spring
17 and another washer 16, followed by a paper holding
ring 5. Insert a screw 12 into the threaded block on each
holding ring.
2.3 Attach the side frames to each end of the paper bars as
shown in the main drawing using the four wing bolts 13.
2.4 Fit the bottom tool tray between the side frames and bolt
it to each leg using bolt 10, nut 22 and washer 23.
2.5 Attach the upper paper blade 7 to the front of the frame
using two screws 10, two nuts 22 and two washers 23.
2.6 Attach the lower cutting blade 7 to the front of the frame
using two screws 10, two nuts 22 and two washers 23.
2.7 Attach a paper spring 7A to the back edge of each
cutting blade. Hook one end of the spring to the notched
back corner of the metalwork and stretch it across and
hook it to the other back corner. Take care to avoid the
cutting blade teeth when doing this.
2.8 To assemble the four tape reels as shown in Fig.2 take a
long bolt 14 and screw on to it a wing nut 6 then drop a
washer 23 onto it followed by a metal bush 21. Slide a
reel 8 over the bolt and onto the bush ensuring that it is
the right way round. Retain the assembly using another
washer followed by a wing nut 6. After the nut has been
tightened the reel should still run freely on the bush.
Attach another nut to the bolt and insert the bolt through
the frame in one of the four places indicated on the main
drawing. Retain the assembly in place using a nut 22
and a washer 23.
2.9 Attach the small tool tray 15 to the side of one of the
frames using two screws 10, two nuts 22 and two
washers 23. The nuts and washers should be on the
inside of the tray.
2.10 Attach the hanger 9 to the side of the opposite frame
at the same level as the top tray. Insert the ends of the
hanger into the holes in the side of the frame, tip the
hanger forwards so that the first bend in either end of
the hanger is inside each frame tube.
2.11 The MK66.V4 has a solid rod axle 4 with holes at either
end to accept cotter pins 11. Slide the axle through the
holes near the bottom of each rear leg.
2.12 Slide a wheel 3 onto each end of the axle and retain it
with a cotter pin 11 through the axle. Secure by bending
the pin back onto itself.
2.13. Push a plastic tube cover 19 over each front leg.
© Jack Sealey Limited
INSTRUCTIONS FOR:
MASKING PAPER DISPENSER
MK66.V4
MODEL No:
Fig.1
1 FRONT FRAME
1A REAR FRAME
2 TOOL TRAY (LARGE)
3 WHEEL
4 AXLE
5 PAPER HOLDING RING
6 WING NUT
7 CUTTING BLADE
7A CUTTING BLADE SPRING
8 TAPE REEL
9 HANGER BAR
10 BOLT
11 COTTER PIN
Original Language Version
12 WING BOLT M5 x 15
13 WING BOLT
14 LONG BOLT
15 SMALL TOOL TRAY
16 PAPER HOLDING WASHER
17 PAPER HOLDING SPRING
18 HANDLE GRIP
19 PLASTIC TUBE COVER
20 PAPER BAR
21 BUSHING FOR TAPE REEL
22 NUT M6
23 WASHER M6
MK66.V4 Issue: 1 - 24/06/16