DeWalt D26200 Original Instructions Manual page 34

EnGLIsH
Subbase
11
[the round subbase 32 and the D-subbase
as an accessory.]
Vacuum attachment (for use with plunge base)
12
Holes for Premium parallel fence (D26203, D26204)
13
Turret stop
14
Depth adjustment rod
15
Plunge lock lever
16
Parallel fence
17
Guide pins
18
Locking lever adjustment screw
19
Centering tool
20
Collet nut
21
Vacuum attachment (fixed base)
22
Screws (vacuum attachment, fixed base)
23
Parallel fence slot (plunge base)
24
Date code
25
Motor unit
26
Motor stop
27
Thumb screw
28
Knurled knob
29
Depth adjustment scale
30
31 Zero adjuster tab
Round subbase
32
D-shaped subbase
33
34 Tab (vacuum attachment, plunge base)
Snap Tab (vacuum attachment)
35
Plastic Washer (vacuum attachment)
36
37 Thumb Screw (vacuum attachment)
Sub-base screws
38
Parallel fence screws
39
Intended Use
Your heavy-duty compact router has been designed for
professional heavy duty routing of wood, wood products
and plastics.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These compact routers are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
32
ASSEMBLY AND ADJUSTMENTS

33 are available
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Cutters
The tooling can be used with the complete range of commercial
cutters (e.g: straight, rebate, profile cutter, slotter cutter or
grooved knife) with the following technical data:
1. Shank diameter 6–8 mm
2. Cutter speed of min. 30000/min

WARNING: Max diameter to use:
•
•
•
Motor Quick Release (Fig. B)

WARNING: To reduce the risk of injury, turn unit
off and disconnect it from power source before
installing and removing accessories, before
adjusting or when making repairs. An accidental start-
up can cause injury.
1. Open the locking lever
2. Grasp the motor unit with one hand, depressing both quick
release tabs
3. With the other hand, grasp the base and pull motor from
the base.
Cutter Installation and Removal (Fig. C)

WARNING: To reduce the risk of injury, turn unit
off and disconnect it from power source before
installing and removing accessories, before
adjusting or when making repairs. An accidental start-
up can cause injury.
To Install the Cutter
1. Remove the motor unit from the base unit, refer Motor
Quick Release, if needed.
2. Clean and insert the round shank of the desired router cutter
into the loosened collet as far as it will go and then pull it
out about 1.6 mm.
3. Depress the spindle lock button
in place while turning the collet nut
wrench provided.
For straight-cutters, rabbet-cutters, profile cutters,
the maximum shank diameter MUST be 8 mm, the
maximum diameter MUST be 30 mm, the maximum
cutting depth MUST be 10 mm.
For slotter cutters, the maximum shank diameter
MUST be 8 mm and the maximum diameter MUST
be 25 mm.
For grooved knives, the maximum shank diameter
MUST be 8 mm, the maximum diameter MUST be
30 mm and the maximum cutting width MUST be
4 mm.
9 on the base.
1 .
5 to hold the spindle shaft
21 clockwise with the