Subscribe to Our Youtube Channel
Related Manuals for Crestron DM-RMC-4K-SCALER-C
Summary of Contents for Crestron DM-RMC-4K-SCALER-C
- Page 1 DM-RMC-4K-SCALER-C/-DSP 4K DigitalMedia 8G+ Receivers and ® Room Controllers with Scaler Supplemental Guide Crestron Electronics, Inc.
- Page 2 LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
-
Page 3: Table Of Contents
Contents Introduction Physical Description Top View ......................... 2 Side View, Left ......................3 Side View, Right ...................... 4 Configuration Video Wall Processing ..................... 5 Configuration Using DMTool ..............5 Configuration Using SIMPL Windows ............6 Adjustable Underscan and Overscan ..............6 Configuration Using DMTool .............. -
Page 5: Introduction
® Room Controllers with Scaler Introduction The DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP provide advanced one-box interface solutions for a single display device as part of a complete Crestron ® DigitalMedia™ system. Each device functions as a DM 8G+ receiver, 4K/60 video scaler, ®... -
Page 6: Physical Description
Red LED and recessed push button for Ethernet setup of the default static IP address of the device NOTE: The default static IP address of the DM-RMC-4K-SCALER-C is 192.168.1.221. The default static IP address of the DM-RMC-4K-SCALER-C-DSP is 192.168.1.222. RESET: Recessed push button for reboot of the device ... -
Page 7: Side View, Left
Maximum output level: 4 Vrms balanced or 2 Vrms unbalanced NOTE: The analog stereo audio output is active only when the DM-RMC-4K-SCALER-C is receiving a 2-channel stereo signal. For applications using a multichannel surround sound source, use the DM-RMC-4K-SCALER-C-DSP, which provides a stereo downmix of the multichannel signal. -
Page 8: Side View, Right
Side View, Right The following illustration shows the right side of the DM-RMC-4K-SCALER-C. Side View, Right LAN: 8-pin RJ-45 female, shielded, with two LEDs; 10BASE-T/100-BASETX Ethernet port; Green LED indicates Ethernet link status;... -
Page 9: Configuration
DM-RMC-4K-SCALER-C provides zoom capability and bezel compensation on its output to display a portion of the source image. To configure a video wall, use the Crestron Toolbox™ DMTool or use SIMPL Windows as discussed in the following sections. Configuration Using DMTool An overview of the steps necessary to configure a video wall using DMTool follows. -
Page 10: Configuration Using Simpl Windows
Video Settings Dialog Box—Video Wall and Bezel Compensation Configuration 5. Repeat steps 2-4 for each DM-RMC-4K-SCALER-C that connects to a display for inclusion in the video wall. Configuration Using SIMPL Windows An overview of the steps necessary to configure a video wall using SIMPL Windows follows. -
Page 11: Configuration Using Dmtool
Adjust underscan in slot 3 for the DM-RMC-4K-SCALER-C Scaler. Set the <Scaler_Out_Underscan_Mode> analog input join to the desired value. • Adjust overscan in slot 4 for the DM-RMC-4K-SCALER-C DM Input. Set the <Source_Overscan_Mode> analog input join to the desired value. User-Selectable Output Resolution The output resolution of the scaler is user selectable. -
Page 12: Configuration Using Simpl Windows
Resolution drop-down list. Video Settings Dialog Box—User Resolution Selection Configuration Using SIMPL Windows Using SIMPL Windows, set the output resolution in slot 3 for the DM-RMC-4K-SCALER-C Scaler. To do so, set the <Scaler_Out_User_Resolution_Index> analog input join to the desired value. -
Page 13: Configuration Using Simpl Windows
Video Settings Dialog Box—Standby Timeout Configuration Configuration Using SIMPL Windows Using SIMPL Windows, set the standby timeout in slot 3 for the DM-RMC-4K-SCALER-C Scaler. To do so, set the <Scaler_Out_Standby_Timeout> analog input join to the desired value. NOTE: For detailed information, refer to the SIMPL Windows help file. -
Page 14: Configuration Using Simpl Windows
DM 8G+ input of the DM-RMC-4K-SCALER-C. By default, the EDID is set to DM default 4k 60Hz 2 ch. If a different EDID is desired, use DMTool to configure the EDID. An overview of the steps necessary to configure the EDID follows. -
Page 15: Connection To A Third-Party Hdbaset Transmitter
Connection to a Third-Party HDBaseT Transmitter The DM-RMC-4K-SCALER-C is HDBaseT certified, enabling direct connection to other HDBaseT certified equipment. Via the DM 8G+ input, the DM-RMC-4K-SCALER-C can be connected directly to a third-party HDBaseT compliant source without requiring a DigitalMedia transmitter. -
Page 16: Hdcp 2.2 Compliance
Addition of HDBaseT Transmitter to Slot 5 and COM Port in Slot 1 HDCP 2.2 Compliance The DM-RMC-4K-SCALER-C is compliant with HDCP 2.2. HDCP 2.2, commonly referred to as HDCP 2, is the next generation of HDCP (High-Definition Content Protection). Note the following about HDCP 2: •... -
Page 17: Troubleshooting
DM IN port when not being powered port is not connected to a PoDM+ by the included power pack. power sourcing equipment (PSE) port. (Continued on following page) DM-RMC-4K-SCALER-C/-DSP: 4K DigitalMedia 8G+ Receivers • 13 Supplemental Guide – DOC. 7728A... - Page 18 NOTE: If, for any reason, the factory default settings of the DM-RMC-4K-SCALER-C must be restored, do the following: From the Tools menu in the Crestron Toolbox application, select Text Console and enter the following command: restore y 14 • DM-RMC-4K-SCALER-C/-DSP: 4K DigitalMedia 8G+ Receivers...
-
Page 19: Appendix: Pin Assignments
Pin 8 Pin 1 TX– RX– DM IN Wiring WIRE WIRE NUMBER COLOR NUMBER COLOR Pin 8 Pin 1 Orange/White 5 Blue/White Orange Green Green/White Brown/White Blue Brown DM-RMC-4K-SCALER-C/-DSP: 4K DigitalMedia 8G+ Receivers • 15 Supplemental Guide – DOC. 7728A... - Page 20 Crestron Electronics, Inc. Supplemental Guide – DOC. 7728A 15 Volvo Drive Rockleigh, NJ 07647 (2047537) Tel: 888.CRESTRON 09.16 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
Need help?
Do you have a question about the DM-RMC-4K-SCALER-C and is the answer not in the manual?
Questions and answers