Sealey ElectroStart E/START1224 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Instruction
Manual
1
1. SAFETY
Read the manufacturer's manual for the vehicle being started: the manufacturer may have
9
specific cautions and instructions regarding emergency starting procedures.
Ensure that the vehicle is in a well ventilated area.
9
Apply the handbrake and select neutral or 'park' before attempting to start.
9
Ensure that the ignition switch and all ancillary electrical equipment is switched off.
9
Keep clear of any pulleys, belts etc. that will move once the engine starts.
9
Take care to ensure correct connection polarity; red clamp to positive, black clamp to negative.
9
Energise the E/START1224 only at ambient temperatures between -30°C and 40°C.
9
When not in use, switch off and store in a cool, dry place out of the reach of children.
9
DO NOT allow this power pack to become wet.
8
DO NOT dismantle this E/START1224: there are no user-servicable parts inside.
8
DO NOT use in explosive atmospheres (e.g. the presence of flammable liquids, gases or dust).
8
DO NOT use the E/START1224 if it appears damaged in any way.
8
DO NOT use this product for any purpose other than that for which it is designed.
8
DO NOT leave in direct sunlight or expose to heat.
8
DO NOT use abrasive or solvent cleaners on this product.
8
DO NOT allow children to play with this product
8
DO NOT allow the positive and negative clamps to touch.
8
2
2. INTRODUCTION
12/24V Vehicle jump starting made easy with innovative technology which, unlike traditional boosters, does not require an internal battery. Simply
connect to a flat vehicle battery and the unit will draw power from it and energise itself fully in a matter of minutes. It then pushes full power safely
back through the starting system, jump starting the vehicle. If the vehicle battery is faulty or is holding less than 5 volts the ElectroStart1224 can
be pre-charged via another vehicle's 12 or 24V battery and capable of starting a 24V even when charged via a 12V. No internal battery means no
storage issues. No wait for the battery to charge which means it is ready to use in a matter of minutes. Compact and lightweight for easier handling
and storage, yet still delivers the same result as heavy, bulky, lead acid battery equivalents. Ideal for the professional mechanics and DIY users.
Supplied in a tough storage case.
3
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E/START1224
Output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12/24V
12V Output Start Peak(EN):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000A(500A)
24V Output Start Peak(EN):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1600A(800A)
3
4. CONTROL PANEL
CONTROL PANEL FUNCTIONS
4.1.
ON/OFF Button:
Switches the E/START1224 on to display the level of stored energy. Enables the E/START1224 to energise
from a 12 or 24V battery via the clamp leads. The unit will detect the nominal battery voltage and select the
appropriate range as shown by the voltage indicator lights:
If a 24V battery contains less than 10V, the unit will default to 12V operation (see section 5.1.3.).
Hold the ON/OFF button down to select Override mode if necessary (see section 6.3). having energised the
E/START1224 fully.
Press to turn E/START1224 off.
Voltage Indicator: 12V red, 24V green
Energising Indicator (EI) (fig.1):
Press the ON/OFF button. The EI will show the internal energy of the E/START1224.
With the E/START1224 switched off, and connected to a battery, the EI indicates the charge in that battery.
When the ON/OFF button is pressed, the EI flashes to indicate the internal charge being accumulated from that
battery until the E/START1224 is fully energised, indicated by a steady 14 or 28V green LED.
GLOW Button:
Only used in special circumstances with some diesel engines (see section 6.2).
Fault/Glow/Override Indicator:
Steady red display when the ON/OFF button is pressed indicates incorrect polarity, or battery voltage too low
to energise.
Steady green indicates that the unit is fully energised and ready to start the engine.
Flashing red/green indicates that the Glow function is selected.
Flashing green indicates that the Override function is initialising, steady green indicates that Override is ready.
Flashing red, with both 12 and 24V indicator lit: jump starter is energised to 24V whereas the receiving battery is 12V.
© Jack Sealey Limited
INSTRUCTIONS FOR:
ELECTROSTART® BATTERYLESS POWER
START 500/800A 12/24V
MODEL NO:
Warning:
Explosive
Risk
.
Original Language Version
E/START1224
Wear
Wear Eye
Protective
Protection
Gloves
Warning:
Electricity
fig.1
E/START1224 Issue: 1 - 12/07/16