Sealey VSE211.V4 Instructions For

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instruction protection
manual
1. safety
‰ ‰ WarninG! Do not use this kit or the components from this kit on diesel fuel systems or high pressure petrol injection
‰
‰
systems (in excess of 145psi). ensure you have read and understood the safety aspects of dealing with the fuel injection
system and petrol in general before commencing.
IMPORTANT: Always refer to the vehicle manufacturer's service instructions, or proprietary manual to establish the
current procedure and data.These instructions are provided as a guide only.
‰ ‰ WarninG! ensure all Health and safety, local authority, and general workshop practice regulations are strictly adhered to
‰
‰
when using product.
‰ ‰ maintain tools in good and clean condition for best and safest performance.‰Do not use test kit if damaged.‰
9
‰
9 Account for all tools and parts being used and do not leave them in, or on the engine after use.
‰ ‰
fuel Hazards
‰ ‰ WarninG! Petrol fumes and battery gases are explosive.
‰
‰
‰ ‰ Do not smoke or allow an open flame or sparks in the work area.
‰ 8
Keep a dry chemical (class B) fire extinguisher near to the working area.
9
Avoid fire hazard by using caution when disconnecting fuel lines and installing adaptors - some spillage is inevitable.
9
When connecting to or disconnecting from a fuel system, relieve pressure from system and wrap a cloth around the fuel line fitting to
9
absorb any fuel leakage. Wipe up fuel spills immediately.
fuel leaks
constantly check gauge and adaptor connections for leakage. if you see leakage turn off the ignition or disable the fuel pump, relieve
9
fuel pressure if necessary and correct leaks before continuing.
‰ 8 ‰ Do not let fuel drip or spill onto a hot engine.
‰
‰ Wipe up fuel spills immediately.
9
‰
When using 't' adaptors, secure hose with hose clamps to ensure leak-free connections.
9
check all adaptor sealing washers and 'o' rings are in good condition before use.
9
‰ ‰ Do not allow fuel to remain in the adaptors or hoses after use.
‰ 8
personal / operation
‰ ‰ Wear approved eye protection. A full range of personal safety
9
‰
equipment is available from your sealey dealer.
‰ Keep yourself, clothing and test equipment away from all
9
‰
moving or hot engine parts.
‰ ‰ Do not wear jewellery and tie back long hair.
9
‰
‰ Before performing a test with the engine running (unless the
9
‰
manufacturer's manual states otherwise), set the parking brake
and place the gear selector in neutral or park, and block the drive
wheels.
‰ exhaust gas contains deadly poisonous gases. the test area
9
‰
must be well ventilated - route the exhaust gas outdoors.
‰ ‰ Before repairing the fuel system, turn off the ignition switch and
9
‰
disconnect the battery per manufacturer's procedure.
‰ never disconnect the battery whilst the engine is running.
9
‰
2. introDuction
comprehensive kit of adaptors and fittings for modern schrader test port fuel
injection systems. components fitted with quick coupling system and safety
valve to prevent inadvertent discharge of fuel under pressure. Kit supplied
with large high pressure gauge reading 0-145psi and 0-1000kPa. Gauge
has hanging hook and protective bumper. Pressure release valve fitted with
long drain hose allows safe recovery of fuel. supplied in carry-case.
operation
© Jack sealey limited
instructions for
fuel injection pressure test kit - test port
Vse211.V4
model no:
Wear Warning
protective explosive
gloves material
Original Language Version Vse211.V4 | issue 1 14/10/15