Related Manuals for FoxESS LV5200
Summary of Contents for FoxESS LV5200
- Page 1 LV5200 In order to prevent improper operation before use, please carefully read this manual.
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ........................ 1 2. Symbols ........................1 3. Safety ......................... 2 3.1 Handling ......................2 3.2 Installation ......................2 3.3 Response to Emergency Situations ..............2 3.4 Warning Labels ....................3 4. Product Information ....................4 4.1 Battery Module Specifications ................ -
Page 3: Introduction
The document describes the installation, commissioning, maintenance and troubleshooting of the following low voltage battery listed below. LV5200 Note: 5200 = 5.2kWh Low Voltage The battery chemistry of this product is Lithium Iron Phosphate. This manual is designed for qualified personnel only. -
Page 4: Safety
Do not store the battery near water sources. · 3.2 Installation · Do not connect the LV5200 to inverter conductors or Photo-Voltaic conductors. This will damage the battery and may result in explosion. After unpacking, please check the product for damages and missing parts. ·... -
Page 5: Warning Labels
Fire Situation In situations where the battery is on fire, if it is safe to do so, disconnect the battery pack by turning of the switch to shut off the power to the system. Use FM-200 or Co2 fire extinguisher for the battery and an ABC fire extinguisher for the other parts of the system. -
Page 6: Product Information
4. Product Information LV5200 photovoltaic energy storage system is a 48V energy storage system based on lithium-ion ferrous phosphate battery. It is equipped with a customized battery management system (BMS), which is designed for energy storage applications of household photovoltaic power generation users. -
Page 7: Battery Charge/Discharge Curve
4.2 Battery Charge/discharge Curve 200A 150A 100A Charge Discharge Normal Standby Protect after 5min Protect after 30s Protect immediately 5. Product Features 5.1 Battery System Features The batteries have been fitted with multiple protection systems to ensure the safe operation of the system. Some of the protection system includes: Inverter interface protection: Over voltage, over current, external short circuit, reverse polarity, ·... - Page 8 Communication parallel interface (Link Port0, Link Port1, RS485) and communication interface to inverter (CAN/RS485) LV5200 has two 485 communication units in series operation, one for master control and one for slave control. Network interface description: Link Port0 is connected to the upper battery module, Link Port1 is connected to the lower battery module.
-
Page 9: Installation
6. Installation 6.1 Items in the package Please check if following items are including with the package: Manual Quick Installation Guide Object Quantity Description Object Quantity Description Low voltage battery Communication network cable Bracket Ground wire Power line (2m) Expansion tubes (Battery to inverter) Network cable (3m) Expansion screws... -
Page 10: Clearance
6.2 Clearance Position Min size Left 30cm Right 30cm 30cm Bottom On the ground Make sure to leave a space of at least 30 cm. A clearance of at least 30 cm must be Ieft around the battery pack for proper cooling. Note: Make sure that the battery pack is always exposed to the ambient air. -
Page 11: Installation Steps
6.4 Installation Steps · Mounting STEP-1 Measure and confirm that the bottom of the bracket is 285mm away from the ground, and mark the 5-hole positions on the bracket with a pen. STEP-2 Drill holes with electric drill, make sure the holes are deep enough (at least 50mm) for installation, and then tighten the expansion tubes. - Page 12 STEP-1 Connect BAT + and BAT - to POS + and NEG - respectively. Connect the battery communication network cable to the lithium battery communication port of the inverter. STEP-2 Plug the power plug into any output socket on the left or right of the battery. Connect the communication network cable to the CAN interface of the battery, connect the ground terminal of the battery with the ground wire, and lock the nut.
-
Page 13: System Start Up
STEP-5 Repeat STEP-3 through STEP-4 to insert more batteries (up to 12 batteries). 6.5 System Start up · When connected with inverter, the inverter should be turned on first to avoid the current pulse of the inverter increasing to the battery pack. ·... -
Page 14: Commissioning
1) Before starting, please dial the code to the corresponding position according to the actual number of parallel machines. 2) After pressing the start switch for 1s, all LEDs will be on and flashing, which indicates that the battery is started normally. After pressing the reset switch for 3s, the battery will turn on the discharge function. 3) After the communication with the inverter is disconnected for 10s, the battery will turn off the output. -
Page 15: Exclusion
9.2 Troubleshooting When the red / green LED on the panel is flashing or normally on, it does not mean that the LV5200 is abnormal, it may be just an alarm or protection. Please check the ‘LED status indicators’ in chapter 7 for the detailed faulty definition before any trouble-shooting steps. - Page 16 The copyright of this manual belongs to FOXESS Co., Ltd Wuxi Branch. Any corporation or individual should not plagiarize, partially or fully copy (including software, etc.), and no reproduction or distribution of it in any form or by any means is permitted. All rights reserved.
Need help?
Do you have a question about the LV5200 and is the answer not in the manual?
Questions and answers