VTech DM1111 User Manual

Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
What's in the box
DM1111 Connect
1
DM1111-2
This is an AC powered audio baby monitor. Connect the baby monitor to a non-switched electric
Enhanced Range
outlet to power on.
Connect the baby monitor
Digital Audio Monitor
When you have connected and turned on the baby unit and all the parent units, they will enter
pairing mode automatically. It takes around 10 minutes for the pairing process to complete. When
the parent unit and baby unit are successfully paired, both their power LEDs are on steadily. The
baby monitor is ready to use.
NOTE NOTES
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch controlled electric outlet.
User's manual
• Connect the power adapters in a vertical or floor mount position only. The adapters' prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under the table, or
cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
• Make sure the POWER light is on after the power plug is fully inserted into the power jack of the baby unit.
• With audio reminder feature preset to on, the parent unit plays an audio reminder when it is connected to a
baby unit.
Before use
2
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent
unit is more than 6.5 feet (2 meters) away from
the baby unit. If you hear any high-pitched
noise, move the parent unit further until the
noise stops. You can also press
unit to lower or mute the noise.
1. Make sure your baby unit and parent unit are on.
2. Speak towards the microphone of the baby unit. You
will hear the sound at the parent unit, and see the
visual sound indicators light up.
Note
• When the POWER/LINK LED light flashes, move the parent unit closer to the baby unit (observe the
minimum distance of 6.5 feet / 2 meters). You can also check if the baby monitor is connected to a live power
socket and switched on.
1 set for DM1111
Tip
2 sets for DM1111-2
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby units.
Using the baby monitor (
3
To mute the speaker volume
• Press repeatedly until the volume reaches the
minimum.
Notes
• When the parent unit is in mute, the visual sound indicator
will still indicate the sound detected from the baby unit.
• To unmute, press
volume.
Turn on or off the audio reminder
With audio reminder feature preset to on, the parent unit plays an audio reminder when it is
connected to a baby unit. It reminds you to place the baby unit at least 3 feet (1 meter) away from
your baby, and keep the cords out of the reach of children.
• Press and hold
flashes for 3 times. The audio reminder is disabled.
• Press and hold
flashes for 3 times. The audio reminder is enabled.
Notes
• You can press
• If the speaker volume of the parent unit is turned off, it will resume to the default volume level when the
parent unit plays the reminder.
Install batteries for backup use (
4
This is an AC powered baby monitor. If you want to move around the house with the parent unit
for a few minutes, you can install two AAA alkaline batteries for backup use. Re-connect the baby
monitor to a non-switched electric outlet once you are settled down.
Notes
• Use 2 x AAA batteries (not included). Alkaline batteries are recommended. If you use other kind of batteries,
the performance of the baby monitor varies.
• NO BATTERY RECHARGING from the parent unit.
• Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc) or rechargeable (Ni-Cad,
Ni-Mh, etc) batteries.
• While you insert the batteries, make sure the polarities are correct.
• When the batteries are installed, the parent unit turns on.
• Replace the batteries when the
Install the batteries as shown below.
1. Press down on the battery compartment cover to slide it out.
2. Insert two AAA alkaline batteries into the battery compartment, according to the polarity
indications (+) and (-).
3. Slidethe battery compartment cover until it clicks into place.
Replace the battery
To replace the batteries, slide open the battery compartment cover, and then take out the batteries.
Follow the previous steps to install the new batteries.
on the parent
>6.5ft (2m)
)
Con't
repeatedly until it reaches your desired
for 8 seconds when the parent unit is not in use. The visual sound indicators
for 8 seconds when the parent unit is not in use. The visual sound indicators
or to adjust or mute the volume when the parent unit is playing the reminder.
Optional
light flashes on the parent unit, or you hear two beeps every 10 minutes.
Before use ( )
2
Con't
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby's crib or playpen.
Note
• To avoid interference from other electronic devices, place your baby monitor far away from devices such as
wireless routers, microwaves, cell phones and computers.
1. Place the baby units more than 3 feet (1 meter) away from
your baby.
2. Place the parent unit more than 6.5 feet (2 meters) away
from the baby unit to avoid screeching noise.
Caution
•
The default volume of your parent unit is Level 3, and the
maximum volume is level 5. If you experience high-pitched
screeching noise
from your baby monitor while positioning:
- Make sure your baby units and parent unit are more than
6.5 feet (2 meter) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 1,500 feet
(450 meters) outdoors or 160 feet (50 meters) indoors. The actual
operating range may vary depending on the environmental
conditions and other interferences such as walls, doors and other
obstructions.
Using the baby monitor
3
Power on or off the baby unit
• Press and hold until the POWER light turns
on.
• Press and hold until the POWER light turns
off.
Power on or off the parent unit
• Press and hold until the POWER / LINK light
turns on.
• Press and hold until the POWER / LINK light
turns off.
Adjust parent unit speaker volume
The speaker volume is preset to Level 3 on the parent unit. You can adjust to your preferred sound level.
• Press to decrease the volume, and to increase the volume.
Note
• If you continue to press or when the volume reaches the minimum or maximum setting, the parent
unit will beep twice.
Baby unit overview
1
Press and hold to turn on or off the baby unit.
2 Microphone
3 POWER light
4 Power jack
Parent unit overview
)
Speaker
1
2
(On/off)
Press and hold to turn on or off the parent unit.
3 (Volume up)
Press to increase the speaker volume.
4 POWER / LINK light
5 Power jack
6 Visual sound indicator
Indicate the sound level detected by the baby unit or show the volume level during
speaker volume setting.
7
(Volume down)
• Press to decrease the speaker volume.
• Press repeatedly until the volume reaches the minimum to mute the parent unit.
8
(Low battery light)
9 Belt clip
10 Battery compartment cover
1
> 3ft (1m)
2
> 6.5ft (2m)
< 6.5ft (2m)
(On/off)