Related Manuals for Insignia NS-DWR3SS1
Summary of Contents for Insignia NS-DWR3SS1
- Page 1 INSTALLATION GUIDE Top Control Dishwasher NS-DWR3SS1 Before using your new product, please read these instructions to prevent any damage.
-
Page 2: Table Of Contents
Specifications ....................23 Introduction Congratulations on your purchase of a high-quality Insignia product. Your NS-DWR3SS1 represents the state of the art in dishwasher design and is designed for reliable and trouble-free performance. -
Page 3: Before You Begin
– The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately call Insignia Customer Service at 1-877-467-4289. FOR YOUR SAFETY Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations described in this booklet, gloves and safety glasses or goggles should be worn. -
Page 4: Preparing To Install Your Dishwasher
Preparing to install your dishwasher Parts supplied: Hose clamp Top mounting clips (2) Wood screws (4) Drain hose Tools needed: Level 1/4 in. and 5/16 in. Phillips screwdriver Nut driver Flat blade screwdriver Adjustable wrench Flashlight Gloves Bucket New installations only Measuring tape Safety glasses Hole saw set... -
Page 5: Enclosure Requirements
Top Control Dishwasher Enclosure requirements • The dishwasher includes a drain hose. If you are installing this dishwasher with a different drain hose, make sure that the drain hose is no more than 10 feet (3.01 m) in length, for proper drainage. •... -
Page 6: Drain Requirements
Drain requirements • Follow all local codes and ordinances. • Do not exceed 10 ft. (3.01 m) of drain hose. • Do not connect the drain lines from other devices to the dishwasher drain hose. • The dishwasher must be connected to a waste line with an air gap (not provided) or a 32 in. (81.28 cm) high (min.) drain loop, depending on local codes and ordinances, to prevent back flow into the dishwasher. -
Page 7: Electrical Requirements
Top Control Dishwasher Electrical requirements • This appliance must be supplied with 120V, 60 Hz electricity, and connected to its own, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. • Wiring must be two wire with ground. •... -
Page 8: Cabinet Preparation And Wire Routing
Cabinet preparation and wire routing • The wiring may enter the opening from either side, the rear, or the floor within the shaded area. • The electrical connection is on the right front of the dishwasher. • Drill a 1-1/2 in. (3.81 cm) maximum diameter hole to run the electrical cable through the wall of the cabinet. •... -
Page 9: Connecting The Water Line To The Water Supply
Top Control Dishwasher The power cable (the square tie is for a fixed power cord.) 2.5-3.5 in. (6.5-9.0 cm) 5.3 - 7.3 in. (13.5-18.5 cm) from cabinet The water supply line (the square tie is for the fixed water supply line.) Connecting the water line to the water supply Turn off the water supply. -
Page 10: Installation Instructions
Installation instructions Step 1: Check the door balance CAUTION: • Opening the door of your dishwasher before it is installed will cause it to tip forward. Do not open the door until you are ready to install your dishwasher. • If it is necessary to open the door, hold the top of the dishwasher securely with one hand and hold the door with the other hand. Hold the top of the dishwasher firmly. -
Page 11: Step 3: Adjust The Leveling Legs
Top Control Dishwasher Step 3: Adjust the leveling legs You’ll need: 1/4 in. and 5/16 in. nut Adjustable wrench Phillips screwdriver driver Move the dishwasher close to the installation location and lay it on its back. Measure the installation height and the dishwasher height. Extend the leveling legs out from the dishwasher base 1/4 in. - Page 12 Install the lock nut on the strain relief from inside the junction box. Insert the ends of the power cord’s electrical wires into the junction box through the strain relief. Connect the incoming white (or ribbed) wire to the dishwasher’s white wire, the black (or smooth) wire to the dishwasher’s black wire, and the ground wire to the dishwasher’s green wire.
-
Page 13: Step 5: Install The 90° Water Supply Elbow
Top Control Dishwasher Step 5: Install the 90° water supply elbow You’ll need: Adjustable wrench 90° elbow Teflon thread seal tape Wrap the male thread of the 90° elbow with Teflon thread seal tape. Do not use plumber's putty. Install the 90° elbow onto the water valve. Do not over-tighten the 90° elbow. The water valve bracket could bend or the water valve fitting could break. -
Page 14: Step 6: Connecting The Water Supply Line
Step 6: Connecting the water supply line You’ll need: Adjustable wrench Waterline kit Teflon thread seal tape Wrap the 90° elbow with Teflon tape twice. Slide the compression nut, then the ferrule over the end of the water supply line. Note: If you have a threaded line you do not need a ferrule or compression nut. -
Page 15: Step 7: Install The Drain Hose
Top Control Dishwasher Step 7: Install the drain hose You’ll need: Screw-type Blade screwdriver hose clamps Drain hose Turn the dishwasher upright. Slide a screw-type hose clamp onto the drain hose. Install the drain hose to the dishwasher drain outlet on the back of the dishwasher, then tighten the screw-type hose clamp. -
Page 16: Step 8: Inserting The Drain Hose Through The Cabinet
Step 8: Inserting the drain hose through the cabinet • Insert the drain hose into the hole in the cabinet wall. If a power cord is used, guide the end through a separate hole. Tip: Position the water line and house wiring on the floor to avoid interfering with the base of the dishwasher. Maximum drain hose length 10 ft. -
Page 17: Step 10: Position The Dishwasher Under The Countertop
Top Control Dishwasher Step 10: Position the dishwasher under the countertop Make sure that the wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. Tip: Check the tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door. -
Page 18: Step 11: Level The Dishwasher
Step 11: Level the dishwasher You’ll need: Level Adjustable wrench Phillips screwdriver The dishwasher must be level for proper dish rack operation and wash performance. Important: Open the door, then place a level on the door and on the rack track inside the tub to make sure that the dishwasher is level. -
Page 19: Step 12: Securing The Dishwasher To The Countertop
Top Control Dishwasher Step 12: Securing the dishwasher to the countertop You’ll need: Wood screws (2) Top mounting clips (2) Phillips screwdriver (two for each method) • For countertops made of wood or materials that won’t be damaged by drilling, use Method 1. •... -
Page 20: Step 13: Connecting The Drain Hose
Reinsert the plastic tub caps. Plastic tub Screw Plastic tub Step 13: Connecting the drain hose You’ll need: Screw-type Coupler for extending Phillips screwdriver hose clamps drain line (if applicable) Important: Follow all local codes and ordinances. Cut on the marked line as required for your installation. The drain hose’s molded end will fit 5/8” or 1" diameter connections on the air gap, waste tee, or garbage disposal. - Page 21 Top Control Dishwasher If a longer drain hose is required, you can add up to 42" (1.1 m) of length, for a total of 10 ft. (3.01 m) to the factory installed hose. Use 5/8” or 7/8” inside diameter hose and a coupler to connect the two hose ends. Secure the connection with screw-type hose clamps.
-
Page 22: Step 14: Performing A Pre-Test Check
If connecting the drain line to a garbage disposal, make sure that the drain plug has been removed. Your dishwasher will not drain if the plug is left in place. Remove the plug Step 14: Performing a pre-test check Review this list after installing your dishwasher to avoid problems or charges for a service call not covered by your warranty. -
Page 23: Step 16: Replacing The Toekick
Top Control Dishwasher Step 16: Replacing the toekick You’ll need: Phillips screwdriver • Place the toekick against the legs of the dishwasher. The slots should align with the toekick bracket screw holes. Allow the toekick to touch the floor. Install the toekick screws. Specifications Capacity Max 16 place settings... - Page 24 For product inquiries, please contact us with the information below: 1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. V1 ENGLISH ©2020 Best Buy. All rights reserved.
Need help?
Do you have a question about the NS-DWR3SS1 and is the answer not in the manual?
Questions and answers