Creating User Patterns; Saving User Patterns; Adding Effects With The Grab Switch; Using The Turntable Emulator - Roland MC-307 Turbostart

PTSVNWU
! 
DAAH7 AJ
5HFRUGLQJ8VHU3DWWHUQVLQ5HDOWLPH
Use the following procedure to create your own
Patterns in realtime:
1. Press PTN, then press USER.
2. Use the VALUE dial to select an empty user
Pattern (U:001-200).
3. Press PART SELECT and use the PART buttons
(R-7) to select a Part.
4. Press REC, then press F2 [Real Time] The
metronome should start.
5. Press F1 [Patch] and use the VALUE dial to
select the desired sound. Press EXIT.
6. Press PLAY to begin recording and use the
black and white keyboard PADS to input the
desired sounds.
7. Repeat steps 3-6 to add additional parts to the
pattern.
6DYLQJ8VHU3DWWHUQV
Once you have created a new pattern, use the
following procedure to save it for future use:
1. Press SYSTEM, then press F3 [WRITE].
2. Press F3 [PTN] and use the VALUE dial to select
the desired destination (U:001-200).
3. Press F4 [WRITE].
4. Use the CURSOR buttons and the VALUE dial to
name the Pattern.
5. Press F4 [OK], followed by F4 [EXEC].
8VLQJWKH*UDE6ZLWFK
Use the following procedure to add effects to a
Pattern with the GRAB switch:
1. Press PTN, then press PRESET.
2. Use the VALUE dial to select Pattern 40 "New
Electro 1."
3. Press PLAY.
4. Push the GRAB switch to ON and listen to the
Pattern with effects.
5. You can use the ASSIGNABLE KNOBS 1-4 to
change the effects parameters in real time.
6. Pull down on the GRAB switch and switch
between OFF and GRAB. This allows you hear
the Pattern with realtime on/off operation of the
effects.
7. Press STOP to end playback.
7%6 Ë  5RODQG &RUSRUDWLRQ 86  6 (DVWHUQ $YH /RV $QJHOHV &$ 
®
%:7-4$9,79
8VLQJWKH7XUQWDEOH(PXODWRU
Use the following procedure to experiment with the
TURNTABLE EMULATOR:
1. Select and Play a preset pattern (as previously
described).
2. Press the PITCH and BPM buttons so they are
lit.
3. Move the TURNTABLE EMULATOR slider up
and down. When the PITCH and BPM buttons
are lit, you will hear a change in both the pitch
and tempo.
4. Try moving the slider up and down with just the
BPM button lit to change the tempo.
5. Now try moving the slider with just the PITCH
button lit to change the pitch.
6. Press STOP to end playback.
6\QFLQJZLWKWKH7XUQWDEOH(PXODWRU
Use the following procedure to sync the MC-307 with
an external device using the TURNTABLE
EMULATOR:
1. Select a preset pattern (as previously described).
2. Press PART MUTE and mute tracks 1-7 so that
just the drums are playing.
3. Start an external device (Turntable, CD player,
etc.) and make sure that the device can be
heard through speakers.
4. On the MC-307, tap quarter notes along with the
music using the TAP button and match the
tempo to the external device as best you can.
5. Press PLAY on the MC-307 with the downbeat of
a measure in the music.
6. Use the TURNTABLE EMULATOR slider with
the BPM button lit to further adjust and match the
two tempos. You can also use the PUSH and
HOLD buttons to "fine tune" the tempos.
7. If you are using backing instrument tracks on the
MC-307, you can use the slider with just the
PITCH button lit to match the pitches of the two
devices.
8. Press STOP to end playback.
)D[EDFN   3DJH