Replacing Thermal Paper - Arkray AUTION ELEVEN AE-4022 Quick Reference Manual

1 Cut the thermal recording paper
from the printer, the screen message shown in the right
figure appears and a continuous beep sounds for
a Check that the [Standby screen] is displayed.
approximately 1 minute. The alarm sound can be stopped
c If some thermal recording paper still remains in the printer, cut
by pressing
the remaining paper strip using scissors and remove the depleted
roll's paper core.
If the paper has completely run out, remove the paper core from
the paper holder and go to step 3.
SEMI-AUTOMATED URINE ANALYZER
AUTION ELEVEN
AE-4022
3 Prepare a new roll of thermal recording paper
b Open the printer cover.
Replacing thermal recording paper
a Cut the first (outermost) layer of a new thermal recording paper
roll, and trim the end to make it straight. A skewed or odd-shaped
1. Check that the [Standby screen] is displayed,
end may cause the thermal recording paper to jam.
then open the printer cover.
2 Remove the remaining thermal recording paper
c If some thermal recording paper still remains in the printer, cut
a Press . The thermal recording paper remaining in the printer
2. Press to remove any remaining paper in
the remaining paper strip using scissors and remove the depleted
is fed out. Remove the paper by holding it with your fingertips.
the printer.
roll's paper core.
If the paper has completely run out, remove the paper core from
3. Cut the fi rst (outermost) layer of a new paper roll and trim
the paper holder and go to step 3.
the end to make it straight. A skewed or odd-shaped end
may cause the paper to jam.
4 Set the new thermal recording paper roll
a Place the new roll of thermal recording paper in the paper holder,
4. Place new roll of thermal recording paper in paper holder so
that paper feeds from the bottom. Guide the trimmed end of the orienting it correctly so that the paper feeds from the bottom.
AE-4022
4-12
thermal recording paper into and through the slot that receives
Guide the trimmed end of the thermal recording paper into and
the recording paper. The thermal recording paper is automatically
through the slot that receives the recording paper.
wound forward and fed into the unit.
The thermal recording paper is automatically wound forward and
2 Remove the remaining thermal recording paper
fed into the unit.
NOTE:
a Press
Always press the
NOTE:
paper. If you do not fully feed the thermal recording paper through is fed out. Remove the paper by holding it with your fingertips.
the unit by pressing the
Always press the
measurement results.
recording paper.If you do not fully feed the thermal
recording paper through the unit by pressing the
the printer will fail to print the measurement results.
5. Close printer cover.
REFERENCE:
If the printer fails to properly wind and feed the thermal recording paper, press
1 Cut the thermal recording paper
.
a Check that the [Standby screen] is displayed.
™
NOTE:
When the thermal recording paper is completely removed
b Open the printer cover.
from the printer, the screen message shown in the right
figure appears and a continuous beep sounds for
approximately 1 minute. The alarm sound can be stopped
by pressing .
3 Prepare a new roll of thermal recording paper
c If some thermal recording paper still remains in the printer, cut
the remaining paper strip using scissors and remove the depleted
a Cut the first (outermost) layer of a new thermal recording paper
roll's paper core. roll, and trim the end to make it straight. A skewed or odd-shaped
end may cause the thermal recording paper to jam.
If the paper has completely run out, remove the paper core from
the paper holder and go to step 3.
4 Set the new thermal recording paper roll
a Place the new roll of thermal recording paper in the paper holder,
orienting it correctly so that the paper feeds from the bottom.
Guide the trimmed end of the thermal recording paper into and
through the slot that receives the recording paper.
2 Remove the remaining thermal recording paper
. The thermal recording paper remaining in the printer
button after replacing the thermal recording
The thermal recording paper is automatically wound forward and
fed into the unit.
a Press button, the printer will fail to print the . The thermal recording paper remaining in the printer
button after replacing the thermal
is fed out. Remove the paper by holding it with your fingertips. NOTE:
Always press the button after replacing the thermal
recording paper.If you do not fully feed the thermal
recording paper through the unit by pressing the
the printer will fail to print the measurement results.
REFERENCE:
If the printer fails to properly wind and feed the thermal recording paper, press
correctly.
Take out.
Cut using scissors.
4.2 Replacing the thermal recording paper
Maintenance – As Needed
NOTE:
NOTE:
NOTE:
When the thermal recording paper is completely removed
When the thermal recording paper is completely removed
from the printer, the screen message shown in the right
When paper is removed from printer,
from the printer, the screen message shown in the right
figure appears and a continuous beep sounds for figure appears and a continuous beep sounds for
error message E004 appears and a
approximately 1 minute. The alarm sound can be stopped
approximately 1 minute. The alarm sound can be stopped
beep sounds for 1 minute. The alarm
by pressing .
Take out.
can be stopped by pressing
by pressing
Cut using scissors.
Cut using scissors.
3 Prepare a new roll of thermal recording paper
a Cut the first (outermost) layer of a new thermal recording paper 3 Prepare a new roll of thermal recording paper
Correct Incorrect Incorrect
roll, and trim the end to make it straight. A skewed or odd-shaped
end may cause the thermal recording paper to jam.
a Cut the first (outermost) layer of a new thermal recording paper
roll, and trim the end to make it straight. A skewed or odd-shaped
end may cause the thermal recording paper to jam.
4 Set the new thermal recording paper roll
a Place the new roll of thermal recording paper in the paper holder,
orienting it correctly so that the paper feeds from the bottom.
Paper holder
Guide the trimmed end of the thermal recording paper into and
Paper Holder
through the slot that receives the recording paper.
4 Set the new thermal recording paper roll
The thermal recording paper is automatically wound forward and
Paper holder
fed into the unit.
button,
a Place the new roll of thermal recording paper in the paper holder,
button,
orienting it correctly so that the paper feeds from the bottom.
NOTE:
Always press the button after replacing the thermal
Guide the trimmed end of the thermal recording paper into and
recording paper.If you do not fully feed the thermal
through the slot that receives the recording paper.
recording paper through the unit by pressing the
the printer will fail to print the measurement results. and verify that the paper feeds
The thermal recording paper is automatically wound forward and
4.2 Replacing the thermal recording paper
Printer cover
Printer cover
.
.
Take out.
Set the new roll of thermal
Set the new roll of thermal recording
recording paper in the
paper in the paper holder in the
paper holder in the proper
Set the new roll of thermal
proper orientation so that the end
recording paper in the orientation so that the end
paper holder in the proper feeds from the bottom.
feeds from the bottom.
orientation so that the end
feeds from the bottom.
Set the new roll of thermal
Paper holder
recording paper in the
paper holder in the proper
orientation so that the end
button,
feeds from the bottom.
and verify that the paper feeds
4.2
12