Sony SRP-X700P Service Manual page 16

Default settings
INPUT
Item Initial setting
MIC1 - MIC4 –60 dBu
TRIM MIC5/LINE1, MIC6/LINE2 +4 dBu
LINE3, LINE4A - 4F –10 dBu
MIC1 - MIC4 ON
LCF
MIC5/LINE1, MIC6/LINE2 OFF
PEQ OFF
FR OFF
COMP OFF
MUTING OFF
GAIN LIMIT +10 dB
INPUT FADER 0 dB
Band 1 63 Hz
FREQ Band 2 2.5 kHz
MIC1 - MIC4
Band 3 20 kHz
MIC5/LINE1,
Band 1 1.0
MIC6/LINE2
Q Band 2 1.5
PEQ
Band 3 0.47
GAIN Band 1 - 3 0 dB
Band 1 63 Hz
FREQ
Band 2 20 kHz
LINE3, LINE4
Band 1 1.0
PEQ Q
Band 2 0.47
GAIN Band 1,2 0dB
ROUTING
Routing Mix level
LINE OUT1, LINE OUT2 –20 dB
MIC1/WL1
LINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0dB
LINE OUT1, LINE OUT2 –20 dB
MIC2/WL2
LINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dB
LINE OUT1, LINE OUT2 –20 dB
MIC3
LINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dB
LINE OUT1, LINE OUT2 –20 dB
MIC4
LINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dB
MIC5/LINE1 LINE OUT1, REC OUT1 0 dB
MIC6/LINE2 LINE OUT2, REC OUT2 0 dB
L LINE OUT1 0 dB
LINE3
R LINE OUT2 0 dB
L LINE OUT1, REC OUT1 0 dB
⋅ ⋅ ⋅
A B C F
R LINE OUT2, REC OUT2 0 dB
L LINE OUT1, REC OUT1 0 dB
LINE4 C LINE OUT5 0 dB
⋅
D E R LINE OUT2, REC OUT2 0 dB
SW LINE OUT6 0 dB
LS LINE OUT3 0 dB
RS LINE OUT4 0 dB
ROUTING ATT LEVEL
CH1 LINE OUT1 –10 dB
SP OUT
CH2 LINE OUT2 –10 dB
AUTOMATIC MIXER OFF
Troubleshooting
Before contacting us, please check the following again. If the trouble persists, please contact your local Sony Sales office or Dealer.
Start the supplied software SRP-X700P Manager and check the settings of the SRP-X700P. Check the following if the problem still
cannot be solved.
Symptom
Power is not turned on. • Power cord is disconnected.
→ Firmly insert the power cord fully into the AC IN terminal and wall outlet.
No sound is output. • Input fader is decreased.
→ Increase the input fader.
• Master volume is decreased.
→ Increase the master volume.
• ROUTING setup is incorrect.
→ Set the ROUTING correctly using the SRP-X700P Manager.
No microphone sound is output. • MIC/LINE selector button is set to LINE.
→ Set the MIC/LINE selector button to MIC.
Sound is distorted. • The LINE equipment is connected to MIC5/LINE 1 IN and MIC6/LINE 2 IN terminals
while the MIC/LINE selector button is set to the MIC position.
→ Set the MIC/LINE selector button to LINE.
No video comes out. • Video input signal setup is incorrect.
→ Set the video input signal correctly again.
The SRP-X700P cannot be controlled • The cable routing method does not satisfy the specifications of this unit.
by RS-232C. • The RS-232C parameter settings do not satisfy the specifications of this unit.
→ Connect cables following the instructions for "REMOTE RS-232C Terminal" described on
page 10.
PROTECTION indicator remains lit. • When DC voltage appears in the SPEAKER terminal due to failure.
→ Set the POWER switch to OFF.
• If the heat sink temperature inside the amplifier exceeds the specified value.
The connected speaker impedance is too low.
→ Set the POWER switch to OFF and connect the SRP-X700P to a speaker having the
correct impedance.
Air intake and exhaust holes (on the right and left sides of the SRP-X700P) are choked
by dust.
→ Clean the air intake and exhaust holes by removing dust with a vacuum cleaner.
• Speaker terminal is short-circuited.
→ Set the POWER switch to OFF and remove the cause of the short-circuit.
OUTPUT
Item Initial setting
OUTPUT1, OUTPUT2 +4 dBu
REF LEVEL OUTPUT3 - OUTPUT8 –5 dBu
REC OUT1, REC OUT2 –5 dBu
HCF OFF
EQ OFF
DELAY 0 ms
MUTING OFF
GAIN LIMIT +10 dB
OUTPUT FADER 0 dB
Band 1 25 Hz
Band 2 40 Hz
Band 3 80 Hz
Band 4 160 Hz
Band 5 315 Hz
OUTPUT1, FREQ Band 6 630 Hz
OUTPUT2 Band 7 1.25 kHz
EQ Band 8 2.5 kHz
Band 9 5 kHz
Band 10 10 kHz
Band 11 20 kHz
Q Band 1 - 11 1.5
GAIN Band 1 - 11 0 dB
HCF OFF
Band 1 63 Hz
Band 2 250 Hz
FREQ
Band 3 2.5 kHz
OUTPUT3 - Band 4 20 kHz
OUTPUT8 Band 1 1.0
EQ Q Band 2, 3 1.5
Band 4 0.47
GAIN Band 1 - 4 0 dB
HCF OFF
MODE Lo Imp.
CH1 OUTPUT 1
SPEAKER SELECT
CH2 OUTPUT 2
OUTPUT
CH1 10 dB
ATT
CH2 10 dB
Cause/Remedy
— 16 —
Default settings
REMOTE
Item
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
INPUT INPUT6
INPUT7
INPUT8
INPUT9
INPUT10
INPUT11
PARALLEL I/O
INPUT12
OUTPUT1
OUTPUT2
OUTPUT3
OUTPUT4
OUTPUT OUTPUT5
OUTPUT6
OUTPUT7
OUTPUT8
OUTPUT9
OUTPUT10
MACHINE TYPE
LINE3
CTRL S OUTPUT CH
MACHINE TYPE
LINE4A
CTRL S OUTPUT CH
MACHINE TYPE
LINE4B
CTRL S OUTPUT CH
MACHINE TYPE
LINE4C
MACHINE CTRL S OUTPUT CH
CONTROL MACHINE TYPE
LINE4D
CTRL S OUTPUT CH
LINE4E, MACHINE TYPE
LINE4F CTRL S OUTPUT CH
CH1
CONNECTION CH2
TYPE CH3
CH4
I/F TYPE
PROJECTOR PROTOCOL
PROJECTOR REMOTE POWER ENABLE
CONTROL LINE4A - LINE4C
INPUT VIDEO
LINE4D
TYPE
LINE4E, LINE4F
15 16
GROUP FADER
Initial setting Item Initial setting
AV SEL A MASTER A MIC1/WL1, MIC2/WL2, MIC3, MIC4
AV SEL B MASTER B MIC5/LINE1, MIC6/LINE2, LINE3, LINE4
AV SEL C REMOTE1 - REMOTE6 Not assigned
AV SEL D
AV SEL E
AV SEL F
RECALL 1
RECALL 2
RECALL 3
LVL Master A
LVL Master B
NONE
AV SEL A
AV SEL B
AV SEL C
AV SEL D
AV SEL E
AV SEL F
RECALL 1
RECALL 2
RECALL 1
RECALL 2
MD
1
VTR3 (VHS)
2
VTR4 (DV)
2
NONE
1
DVD
3
NONE
1
WIRED
WIRED
IR
WIRED
RS-232C
VPL-FX50
ON
VIDEO
COMPONENT
RGB