Advertisement
3. SET UP
3.1.
Installing/Changing Battery (fig.1)
3.1.1.
On either side of the trigger, where the handle moulding meets the main
body there are two very shallow recesses. Place thumb and finger into
these recesses and pull the front section of the handle forward and down to
reveal the battery compartment.
3.1.2.
Attach the battery connector to the battery terminals and place the battery
into the battery compartment making sure that the connection leads will not
foul the cover when it is closed.
3.1.3.
When the 'battery low' indicator appears on the display replace the battery
immediately, (See Enviromental Protection).
4. OPERATION AND APPLICATION
4.1
Depress the trigger (1) in fig 3 to switch on the unit, the 'SCAN' icon will
illuminate.
4.2
Decide what units are required by pressing the '°C/°F' button (3) in fig 3. The
button will toggle between the specified units.
4.3
Pay attention to the distance from the thermometer to the target as the target
surface size increases with distance. A ratio of 12:1 exists, see fig 2.
Make sure the target is larger than the unit's spot size. The smaller the
target, the closer the distance "D". When accuracy is critical ensure the
target is at least twice the spot size.
4.4
The unit is equipped with a laser for the purpose of aiming only. With the
laser button (2) in fig 3 in the 'on' or 'off' mode, aim at the target surface and
depress the trigger. The temperature of the target surface will be displayed
on the LCD display screen. When the trigger is released the reading will be
held for 7 seconds approximately; the 'HOLD' icon will be illuminated in this
period; and then the thermometer will automatically shut down unless the
trigger is depressed again.
4.5
To locate a hot spot on a large surface, aim the thermometer as in 4.4,
then scan across the area with a controlled uniform "zig-zag" sweep until you
locate the spot, as illustrated in fig 4.
fig.4
5. NOTES ON EMISSIVITY
5.1
Emissivity is a term used for the ability of a surface to radiate energy. This unit has been pre-set with an emissivity of 0.95, which
makes it suitable for 90% of typical applications.
5.2
Inaccurate results will occur when targeting shiny or polished surfaces. As a tip, apply a non reflective tape to the area to be tested,
allowing time for the surface temperature of the tape to reach that of the substrate.
6. CLEANING
6.1
The sensor lens is delicate and should be kept clean at all times. Use a cotton bud and medical alcohol, allowing lens to dry. The
casing can be cleaned with a moist cloth and mild soap but never submerged.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible
with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling information.
Open battery compartment as described in Section 3.1. Disconnect battery and remove.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme.
Jack Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited 2012
Trigger
Depressed
Environmental Protection.
Dispose of batteries according to local authority guidelines.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
2) Laser
on/off
4) Back light
on/off
3) Units
°C/°F
01284 757500
Web
01284 703534
email
VS904.V2
fig.1
fig.2
1)Trigger
fig.3
www.sealey.co.uk
sales@sealey.co.uk
Issue: 2(SP) - 22/07/13
Advertisement
