Download Print this page

Sealey CP1207 Quick Start Manual page 2

49pc 12v cordless multi-purpose rotary tool & engraver kit - body only

Advertisement

5.1.5.
Tighten the collet nut firmly. Finally, release the spindle lock button.
5.2.
CHANGING COLLETS
5.2.1.
To change collets, proceed as in paragraphs 5.1.1. to 5.1.3. but continue to unscrew the collet nut until it can be removed from the
spindle. Change collets and replace the collet nut.
5.3.
OPERATION
5.3.1.
Select the speed required on the rotary speed control (fig.1). Small accessories require high speed and large accessories
low speed. If in doubt, start on a low setting and gradually increase the speed until the best performance is obtained.
NOTE: DO NOT switch ON with a tool bit touching the workpiece. Always allow a bit to reach the required speed before applying it
to the workpiece.
5.3.2.
Battery state is indicated by the use of three lights (red, orange, green). All three lit indicates full charge. Red alone lit indicates charge
required.
6. MAINTENANCE
6.1.
CLEANING
6.1.1.
Keep the tool's ventilation slots clean and free from obstructions. If available, blow compressed air into the vents to clear any internal
dust (safety goggles must be worn when undertaking this process).
6.1.2.
Keep the outer case of the tool clean and free from grease.
6.1.3.
Wipe down with a damp cloth. DO NOT wash with water or use solvents or abrasives.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 1.024m/s²
Uncertainty value (k):1.5m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be modified
accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website
www.hse.gov.uk - Hand-Arm Vibration at Work.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
OPERATION
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
WARNING! – Risk of Hand Arm Vibration Injury.
01284 703534
Original Language Version
sales@sealey.co.uk
www.sealey.co.uk
CP1207
Issue 2 (2) 11/05/20

Advertisement

loading