Sealey CP1207 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
Disconnect the battery from the tool before changing accessories, servicing or performing any maintenance.
9
Maintain tool and accessories in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts using recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Wear approved safety eye protection with side shields and a dust mask if generating dust.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use the tool in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
9
Maintain correct balance and footing.
9
Keep children and unauthorised persons away from the work area.
9
Secure unstable work piece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting. Keep the tool clean for best and safest performance.
9
When not in use switch tool off. Store it in the case and put in a dry, childproof area.
9
DO NOT over-reach. Ensure the floor is not slippery and wear non-slip shoes.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT operate tool where there are flammable liquids or gases.
8
DO NOT get the tool wet or use in damp or wet locations.
8
DO NOT hold unsecured work in your hand.
8
DO NOT leave the tool running unattended.
8
DO NOT operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.
8
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
2. INTRODUCTION
i
Compact, lightweight cordless multipurpose rotary tool & engraver. Comfortable composite housing with soft grip to reduce vibration. Six speed
settings provide the control required to complete various tasks. Quick release collet and spindle lock for fast tool changes. Supplied with a full range
of tips, wheels, sanding discs, dressing stones and a chuck spanner. Integral LED battery level indicator. Requires Model No. CP1200BP 12V 1.5Ah
Lithium-ion Battery and Model No. CP1200MC Battery Charger.
3. SPECIFICATION
i
Model no ................................................................... CP1207
Battery options
12V 1.5Ah Li-ion, 12V 3Ah Li-ion, 12V 4Ah Li-ion (not included)
Collets ................................................... 1, 1.5, 2, 2.4, 3.2mm
Consumable parts
CP1200BP - Battery 12V 1.5Ah,
CP1200BP3 - Battery 12V 3Ah,
CP1200BP4 - Battery 12V 4Ah (not included)
Free speed .................................................... 5000-25000rpm
Noise power/pressure .......................................... 74/63dB(A)
Vibration/uncertainty ........................................ 1.024/1.5m/s²
4. CONTENTS
HSS Drill Bits (x6), Mandrel (x2), Polishing Disc (x3), Grinding Disc (x4), Metal Brush, Cutting Disc (x16), Collet Chuck (x5), Synthetic Brush
(x2), Milling Bits (x2), Engraving Bits (x2), Grinding Bits (x5), Combination Spanner
5. OPERATION
5.1. FITTING ACCESSORIES
5.1.1. Ensure the tool is switched off and the battery removed.
5.1.2. Press the spindle lock button and slowly turn the collet nut until the spindle lock engages. Refer to fig.1.
5.1.3. Retain pressure on the spindle lock button and turn the collet nut anticlockwise to open the collet (Spanner provided).
NOTE: Never press the spindle lock button when the tool is running.
5.1.4. The required accessory may now be fitted into the collet. Fully insert the accessory shaft to reduce the risk of bending in use.
© Jack Sealey Limited
49PC 12V CORDLESS MULTI-PURPOSE
ROTARY TOOL & ENGRAVER KIT - BODY
ONLY
CP1207
MODEL NO:
Wear face Wear protective
mask gloves
Original Language Version
fig.1
CP1207 Issue 2 (2) 11/05/20