Trikdis FLEXi SP3 User Manual
Security control panel
Hide thumbs
Also See for FLEXi SP3:
- Installation and programming manual (48 pages) ,
- User manual (17 pages) ,
- User manual (17 pages)
Related Manuals for Trikdis FLEXi SP3
Summary of Contents for Trikdis FLEXi SP3
- Page 1 Security control panel FLEXi SP3 User manual (Protegus, Paradox keypads) August 2020 www.trikdis.com UAB Trikdis Draugystes g. 17, LT-51229 Kaunas, Lithuania +370 37 408 040 info@trikdis.lt...
- Page 2 FLEXi SP3 user manual Attention! Read this user manual carefully. A representative from the company installing the alarm system will explain which functions of the FLEXi SP3 security module must be activated to ensure proper protection of the premises. Copyright ©...
-
Page 3: Table Of Contents
FLEXi SP3 user manual Contents ABOUT YOUR ALARM SYSTEM ............................4 MAIN TECHNICAL SPECIFICATIONS ..........................4 POWERING THE EQUIPMENT............................4 GENERAL OPERATION OF THE ALARM SYSTEM ......................4 ............................. 4 RANSMISSION OF ALERT MESSAGES ............................5 LARM SYSTEM OPERATION MODES ............................ -
Page 4: About Your Alarm System
About your alarm system The FLEXi SP3 control panel is part of a premise security and fire alarm system. It performs sensor signal processing and signalizer control and has integrated GSM and WiFi modems that can transmit alert messages to the central monitoring station and to users’... -
Page 5: Alarm System Operation Modes
User code – a four-digit combination for arming/disarming the alarm system and for temporarily bypassing security zones. It is recommended to assign every user a personal alarm control code. The memory of the FLEXi SP3 module can store up to 40 user codes;... -
Page 6: Additional Functions
Up to 8 temperature sensors DS18B20, DS18S20 or one temperature and humidity sensor AM2301 can measurement be connected to the FLEXi SP3 module. Intervals of permitted temperatures can be set for each of them individually. If the temperature changes beyond the set interval, an event message will be formed and sent to users. -
Page 7: Controlling The Alarm With A Paradox Keypad
FLEXi SP3 user manual Button Description A constantly glowing button shows that in memory there is new information about the alarm being triggered, and a blinking button shows that the keypad is operating in MEM mode. The button is also used for choosing the memory viewing mode. - Page 8 FLEXi SP3 user manual Paradox keypads K32LED, K32+ for alarm system control display the states of 32 zones and 2 partitions. The Paradox K35 keypad for alarm system control displays the states of 32 zones and 2 partitions. Buttons for setting operation modes and entering numbers...
-
Page 9: Quick Arming/Disarming Of The Alarm System
FLEXi SP3 user manual 2. If at least one zone is violated, it will not be possible to arm the alarm system (if the FORCE property is not assigned to the violated zones). 5.3 Quick arming/disarming of the alarm system Arming/disarming the alarm system using a code when the security system has STAY zones. -
Page 10: Disarming The Alarm (Off Mode)
FLEXi SP3 user manual 2. Enter the [User code] using the keypad. 3. Press the buttons with the numbers of the partitions you want to control. 4. Confirm your selection by pressing the [OK] (or [ENTER]) button. 5. The keypad indicator [SLEEP] will begin to glow. -
Page 11: Resetting Fire (Smoke) Sensors
FLEXi SP3 user manual a. If no actions are performed with the keypad, the memory viewing mode will switch off automatically after one minute, but the memory will not be cleared and the [MEM] indicator will continue to glow. 4. The memory will be cleared after the alarm is switched on and the [MEM] indicator stops glowing. -
Page 12: Programming User Control Codes
FLEXi SP3 user manual Trouble group Description of selected group [4]: 485 bus Numbers of 485 bus expanders with malfunctions. [5]: Missing RF sensor A wireless sensor is no longer operational (periodic check time has passed). The zone number shows the order from a separate RF table. -
Page 13: Duress Code
FLEXi SP3 user manual a. The [ ] (or [ ]) button will begin to blink. 3. Enter the desired two-digit user serial number. 4. Press the [SLEEP] button. 5. To leave programming mode, press the [C] (or [CLEAR]) button. -
Page 14: Control Using Sms Messages
PGMx output. Call the number of the SIM card inserted into the FLEXi SP3 security control module. If the phone number you are calling from is specified in the module‘s memory, the control panel will answer the call and you will have to enter the control command (see control command table). - Page 15 FLEXi SP3 user manual Command Data Description TIME YYYY/MM/DD,12:00:00 Set date and time. E.g.: TIME 123456 2020/01/02,12:23:00 TXTA Object name Specify object name. E.g.: TXTA 123456 House PhoneNR#SMStext Forwards SMS messages to the specified number. The phone number must start with a "+"...
- Page 16 FLEXi SP3 user manual Information about the protected object Fill in the following tables. Keep this document in a safe location. Access codes Your Administrator code is ______________________________ Other access codes: Code Control key No. Code Control key No. Zones...
- Page 17 FLEXi SP3 user manual Zone Protected space Zone type Temperature sensors Sensor Serial number Controlled space Max. temperature Min. temperature www.trikdis.com August 2020...
- Page 18 FLEXi SP3 user manual Emergency call buttons Panic __________________________ Alarm system __________________________ Ambulance __________________________ Time intervals Time for entering _________________________ sec. Time for exiting _________________________ sec. Siren operation time _________________________ sec. Additional information ______________________ ____________________ __________________ (name) (phone number) (password)
Need help?
Do you have a question about the FLEXi SP3 and is the answer not in the manual?
Questions and answers