Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ubiquiti UniFi Security Gateway PRO
Summary of Contents for Ubiquiti UniFi Security Gateway PRO
- Page 1 Enterprise Gateway Router with 2 Combination SFP/RJ45 Ports Model: USG-PRO-4...
-
Page 2: Package Contents
Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Security Gateway Pro. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UniFi Security Gateway Pro Enterprise Gateway Router with 2 Combination SFP/RJ45 Ports... -
Page 3: Network Requirement
Network Requirement A UniFi Cloud Key or management station running the UniFi Controller software, located either on-site and connected to the same Layer-2 network, or off-site in the cloud or NOC UAP-AC-PRO UAP-AC-LR UniFi Cloud Key (UniFi Controller) UAP-AC-M-PRO UniFi Switch UniFi Switch USG-PRO-4 (DHCP Server) -
Page 4: Hardware Overview
Hardware Overview Front Panel Ports Console Interface Description RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9 serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed: Console •... - Page 5 Front Panel System LED System State Status White Factory defaults, waiting for adoption. Successfully adopted by a network and Blue working properly. Device is busy; do not touch or unplug it. Alternating This usually indicates that a process such White/Blue as a firmware upgrade is taking place.
- Page 6 Front Panel Port LEDs LAN: Speed/Link/Act WAN: Speed/Link/Act SFP: Speed/Link/Act State Status No Link Link Established at 10/100 Mbps Speed/ Amber Link/ Flashing Indicates Activity Link Established at 1000 Mbps Green Flashing Indicates Activity *640-00128-04* 640-00128-04...
-
Page 7: Front Panel Button
Reset until the right LED on the WAN2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Security Gateway Pro will automatically reboot. Back Panel Mounting Holes Mounting Holes... -
Page 8: Installation Requirements
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Note: Although the cabling can be located outdoors, the UniFi Security Gateway Pro itself should be housed inside a protective enclosure. -
Page 9: Hardware Installation
Hardware Installation WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. 1. Connect the Power Cord to the Power port of the UniFi Security Gateway Pro. - Page 10 2. Attach the UniFi Security Gateway Pro to the rack using the four Mounting Screws. (If the rack has square slots, then use the Cage Nuts with the Mounting Screws.) 3. Connect the other end of the Power Cord to a power outlet.
-
Page 11: Connecting Ethernet
Connecting Ethernet 1. Connect an Ethernet cable from a broadband modem or WAN to the WAN1 port. 2. Connect an Ethernet cable from your computer or host system to the LAN1 port. 3. Connect an Ethernet cable from your network switch to the LAN2 port. - Page 12 Using SFP Ports To use an SFP port: 1. Remove the protective plug covering the SFP port. 2. Plug a compatible fiber module into the SFP port. Note: The corresponding WAN port will be deactivated. 3. Connect a fiber optic cable to the fiber module. Then connect the other end of the cable to another fiber device.
-
Page 13: Software Installation
Software Installation Download the latest version of the UniFi Controller software at: www.ubnt.com/download/unifi From a management station connected to the same Layer-2 network, launch the installer and follow the on-screen instructions. Note: If you already have UniFi Controller v4.8 or higher installed, go to the section, Adopting the UniFi Security Gateway Pro. - Page 14 2. On the Devices screen, locate the UniFi Security Gateway Pro in the list of devices under the Model column. To adopt it, click Adopt. 3. The System LED on the UniFi Security Gateway Pro will turn blue to confirm that it is successfully adopted.
- Page 15 LAN1 port of the UniFi Security Gateway Pro. 1. From a web browser, go to: https://setup.ubnt.com https://setup.ubnt.com 2. The UniFi Security Gateway Pro login window will appear. Enter your Username and Password. Click Sign In. Note: If the UniFi Security Gateway Pro has not been adopted by a UniFi Controller, the login window will be skipped and the Setup window will appear.
-
Page 16: Specifications
Specifications UniFi Security Gateway Pro Dimensions 484 x 44 x 164 mm (19.06 x 1.73 x 6.46") Weight 2.30 kg (5.07 lb) Networking Interfaces Serial Console Port (1) RJ45 Serial Port Data Ports (2) 10/100/1000 RJ45 Ports (2) 10/100/1000 RJ45/SFP Combination Ports Max. -
Page 17: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. -
Page 18: Limited Warranty
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. - Page 19 ISED Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-003. CAN ICES-3(A)/NMB-3(A) Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
- Page 20 RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 21 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 22: Declaration Of Conformity
English Hereby, UBIQUITI NETWORKS, declares that this USG-PRO-4 device, is in compliance with the essential requirements and other relevant provisions of Directives 2014/30/EU, 2014/35/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance... - Page 23 Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta USG-PRO-4 tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo USG-PRO-4, è...
- Page 24 . u b n t . c o m ©2015-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc.
Need help?
Do you have a question about the UniFi Security Gateway PRO and is the answer not in the manual?
Questions and answers