Page 1 Q30 1.1 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein;...
Page 2: Important Safety Information
Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed.
Page 3: Care During Use
Do not put rechargeable batteries or products powered by non-removable rechargeable batteries in the garbage. Contact the Samsung Helpline for information on how to dispose of batteries that you cannot use or recharge any longer. Follow all local regulations when disposing of old batteries.
Page 4: Laser Safety
Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard.
Page 5: Regulatory Compliance Statements
Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device.
Page 6 In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated.
Page 7: United States Of America
United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 8: Fcc Part
The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on.
Page 9 If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Page 10 Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté...
Page 11 Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’...
Page 12: European Union
European Union The following information is only applicable to systems labeled with the CE mark European Directives This Information Technology Equipment has been tested and found to comply with the following European directives: • EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/ EEC as per –...
Page 13 European States qualified under wireless approvals: Austria, Belgium, Denmark, Finland, France (with frequency Germany, Greece, Ireland, Italy, Luxembourg, The restrictions), Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN.
Page 14: Using Your Documentation
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Three icons and their associated messages appear in this manual.
Page 15: Touchpad Conventions
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD.
Page 16: Getting Started
Getting Started Introducing Your Computer The photographs used in this user manual may be somewhat different in shape and colour to those of your computer depending on the model of your computer. Front View Memory Card Slot (p 30) Status Lights (LED) (p15) LCD Panel Keyboard (p8)
Page 17: Back View
Right View Power Button Modem port (p36) CF Card Slot USB Port LAN Port (p33) (2.0) (p37) Left View DC-In Port Microphone 1394 Port Monitor Port Jack (6 Pin) Headphone/ USB Port S/PDIF (2.0) Jack Back View Security Lock Port (p81) Battery (p78) 4 Users Manual...
Page 18: Bottom View
Bottom View Battery Latches 3D Speaker Getting Started 5...
Page 19: Turning The Computer On And Off
Turning the Computer On and Off To turn on the computer 1. Insert the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD latch to the right and open the LCD panel. 3. Press the power button. Since opening the LCD panel by hand might cause damage to the panel, please use both hands when opening the panel.
Page 20 3. Click Turn Off. If the computer is not turned off properly due to a system error, press <Ctrl>+<Alt>+<Delete>. When [Windows Task Manager] dialog box appears, click Shut Down > Turn Off to turn off the computer. Your unsaved work may be lost/damaged.
Page 21: Using The Keyboard
Using the Keyboard Your computer has an 82-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
Page 22: Using The Numeric Keypad
The keys on the keyboard can be grouped into the following categories: • Full-sized Alphanumeric typewriter keys are arranged like a standard typewriter keyboard and are used for text entry. The Windows keys on either side of the spacebar open Windows menus and perform other special functions. •...
Page 23: Using Special Function Keys
Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. <Fn> Key Key Name Combinations <Esc/ > Rest <F2/ > Gauge <F4/ > LCD/CRT <F5/Backlit> Backlight <F6/Mute> Mute <F7/ > 3D sound <F8/ >...
Page 24 <PgUp/Home> Home <PgDn/End> < > Volume Down < > Volume Up < > Brightness Up < > Brightness Down When you press a function key combination, the system sound may be temporarily muted. Moves to the beginning of the sentence. Moves to the end of the sentence.
Page 25: Using The Touchpad
Using the Touchpad In Windows, you always see a small graphical image on the screen that indicates the location where you can take the next action. This image is called a pointer, and is usually displayed in arrow shape ( Touchpad The touchpad on your computer allows you to move the pointer on the LCD screen, just like a mouse that is used with a desktop computer.
Page 26 You can perform various actions with your touchpad as described below. Action Move Click Double-Click Right-Click Drag Function Process Move the pointer Place your finger on the touchpad and slide your finger to a destination. Select an object, open a menu, or Place the pointer over an object, execute a button then press left touchpad button...
Page 27 Action Scroll Make sure to use your finger to move the pointer with the touchpad. Do not use any sharpened tool because it may damage your touchpad. Operating the touchpad or touchpad button while starting your system may increase the time required for starting Windows. 14 Users Manual Function Process...
Page 28: Reading The Status Indicators
Reading the Status Indicators Shows the operating status of the computer. Num Lock Turns on when the numeric keypad is activated. Caps Lock Turns on when all alphabet characters you type will be in upper case. Scroll Lock Turns on when it is set to scroll the screen up and down while the cursor position does not change in some applications.
Page 29: Adjusting Lcd Brightness
Maintaining your LCD brightness settings after turning the system off and on 1. Turn the system on. When the Samsung Logo appears, press the <F2> key to enter Setup. 2. In the Boot menu, change the Brightness Control Mode option to User Control.
Page 30: Adjusting The Volume
Adjusting the Volume To adjust using keyboard Press <Fn>+< > or <Fn>+< To adjust using volume adjustment program Click the Volume icon( level. For advanced volume control options, double-click the Volume icon( the volume level in the volume control program. When you turn the system on, a booting noise may occur.
Page 31: Introducing Windows
Introducing Windows Understanding the Desktop The desktop is the working area on the computer. It consists of the large workspace and a taskbar at the bottom. Shortcut Icons Start Menu Start Button Start Button Taskbar Recycle Bin Language Bar 18 Users Manual Taskbar System Tray with Clock Opens the Start menu.
Page 32: Understanding The Start Menu
Understanding the Start Menu The Start menu includes everything that is required to start Windows. From the Start menu it is possible to run a program, open a file, assign system users with Control Panel, receive support by clicking Help and Support, and search desired items from the computer or Internet by clicking Search.
Page 33: Understanding A Window
Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer's hard drive, will be used as an example here to show the basic composition of a window. Click Start >...
Page 34: Help And Support Center
Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Windows XP Tour You can tour elementary functions provided by Windows XP. Click Start > Tour Windows XP. Or click Start >...
Page 35: Using The Computer
Using the Computer Using the CD Drive(Optional) For this computer, a 1394 external CD-RW/CD-ROM combo or DVD multi drive is provided. To connect a CD drive Connect the CD drive to the 1394 port. To use a CD drive 1. Push the eject button on the CD drive. 22 Users Manual...
Page 36 2. When the tray slides out, place a CD onto the tray with the label facing up, and push the CD down until it clicks. CD Access LED 3. Push the tray in gently until it clicks. To eject a CD 1.
Page 37 To play a DVD You have to install the DVD software provided on a separate CD to view a DVD title. To use the Windows Media Player The Windows Media Player allows you to play audio and video files from the computer or the Internet.
Page 38 5. Select “Select the program from a list” and click OK. 6. Select the Windows Media Player, and click OK. The video starts playing. Above procedure applies only to the video CDs that has a .dat file as the execution file. Playing procedure may be different according to video CDs. To write data on a CD (Option) If your computer has CD-RW functionality, you can copy data to a blank CD or create an audio CD.
Page 39 4. In My Computer window, select files and folders to copy, then drag and drop them onto the CD drive window. 5. Click Write these files to CD in the CD drive window. 6. When the CD Writing Wizard appears, enter the CD label, and click Next. The data begins copying.
Page 40 Enjoying Home Theater (S/PDIF Port) Your computer supports 5.1 channel output, which is a basic function for home theater systems, and DVD drives. It provides 3D surrounding sound and vivid screen. What is a home theater system? Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and digital amp and provides a high-resolution screen (MPEG2) and 3D surrounding sound (Dolby 5.1 or DTS).
Page 41 Step 1. Connect 5.1 channel speaker system to your computer 1. Connect the S/PDIF jack on the left-hand side of the system and the 5.1 channel amplifier. 2. Connect speakers to the amplifier. (Refer to speaker system’s manual.) Digital Amplifier Front Left Speaker Surround Left Speaker You need a TV that supports VGA port to display through a TV.
Page 42 Step 3. Enable S/PDIF output on the DVD program To use 5.1 channel speakers, you need to install the Power DVD program from the DVD Installation CD provided with your computer, then change the settings as per the following. 1. Run Power DVD program and click the Settings icon ( 2.
Page 43: Using Memory Card Slot
Using Memory Card Slot Through the memory card slot, you can use memory cards such as memory stick, SD (Secure Digital) memory card, and MMC (Multi Media Card). You can use the memory cards as a removable disk, and use them to exchange data between your computer and digital devices such as a digital camera.
Page 44: To Remove A Memory Card
1. Insert the card into the memory card slot, logo side facing upwards. 2. Click Start > My Computer. The inserted memory card is displayed. Memory Stick 3. You can write data to the memory card. If the memory card is not formatted yet, format the memory card before use.
Page 45: To Format A Memory Card
To format a memory card You can use a memory card after the format operation. The procedures to format a memory card are described below. Since format operation deletes all data in the memory card, please make sure that there is no important data in the memory card before formatting. To protect the data in the memory card Set the write protection tab of the Memory Stick or SD memory card to the Lock position.
Page 46: Using The Cf Card Slot
Using the CF Card Slot You can insert a CF card, used in multimedia devices such as digital cameras, into the CF card slot and exchange data between the CF card and the computer. 1. Insert a CF card into the CF card slot at the side of the system. 2.
Page 47: Using Samsung Smart Screen
If you select OK, the program is automatically launched when you start your computer. 2. Samsung Smart Screen appears. When you run the program for the first time, water drop image is displayed.
Page 48: Using Samsung Theme
Using Samsung Theme Samsung Theme is a program that enables a user to easily switch a theme (desktop, logon screen and sound effect). Double-click the Samsung Theme ( (Or select Start > All Programs > Samsung > Samsung Theme > Samsung Theme.)
Page 49: Connecting To The Internet
Connecting to the Internet Connecting with a Modem Before Start: • Prepare a telephone line that is not digital. • Contact an internet service provider (ISP) for instructions on how to connect to and disconnect from the Internet. 1. Connect a telephone line to the computer’s modem port. 2.
Page 50 Connecting Through a Wired LAN 1. Connect a LAN cable to the computer’s LAN port. 2. Click Start > Control Panel. 3. Click Network and Internet Connections in the [Control Panel] window. 4. Click Network Connections in the [Network and Internet Connections] window. 5.
Page 51 6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties. 7. To use DHCP: On the General tab, select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click OK. To use a static IP: On the General tab, select “Use the following IP address” and fill in the IP address, Subnet mask, Default gateway, Preferred DNS server, and Alternative DNS server fields.
Page 52: Using Samsung Network Manager
1. Connect LAN cable to the computer's LAN port. 2. Double-click Samsung Network Manager icon on the desktop. Or click Start > All Programs > Samsung Network Manager > Samsung Network Manager. 3. When you are using DHCP, available IP's are displayed in the status dialog box.
Page 53 To change network places You can change network places as below. 1. Connect LAN cable to the computer's LAN port, and double-click Samsung Network Manager icon on the desktop. If you used static IP in previous place, previous static IP is displayed in the status dialog box.
Page 54 2. Click Change, select a place icon then click Change. 3. On "Do you want to change the location setting?" dialog box, click Ok. 4. When the network place is changed, corresponding place icon is displayed in color and full dialog box appears. In the right area of full dialog box, network setting is displayed.
Page 55 Connecting Through a Wireless LAN (Option) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.
Page 56: Connecting To An Access Point (Ap)
What is an Access Point (AP)? An AP is a network device that bridges wired and wireless LANs, and corresponds to a wireless hub in a wired network. You can connect multiple wireless LAN installed computers to an AP. 2) Computer-to-computer (ad hoc) This is also called a peer-to-peer network.
Page 57 Select an AP (E.g. Test) to connect to and click Connect. When the network key dialog box appears, enter the network key and click Connect. When a network key is not defined for a selected AP, click on Link to display the warning message box.
Page 58 Connecting to computer-to-computer networks ad hoc) In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules. Using this method, a computer that is not connected to the Internet can share the Internet by accessing another computer connected to the Internet.
Page 59 Click Change the order of Preferred Networks. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close. 5. In the Wireless Networks tab, click Add. 46 Users Manual...
Page 60 6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key).
Page 61 7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks.
Page 62 2. Select the wireless network name (e.g. samsung) specified in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 45, and click Connect. 3. Enter a cryptographic key in the network key box and click Connect. If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)”...
Page 63 Checking the connection status Move the mouse pointer over the Wireless Network Connection ( ) icon on the taskbar, and the connection status is displayed. 50 Users Manual...
Page 64 Wireless Network Setup Using the Wireless LAN Setup Program(for an 11a/g and 11g card) You can use a wireless LAN by using a wireless LAN configuration program (PROSet) provided separately. For an 11b card, see ”Wireless Network Setup Using the Wireless LAN Setup Program(for an 11b card)”...
Page 65 To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following "To create computer-to-computer (Ad Hoc) network" section.) 1.
Page 66 Network name (SSID) is a name that a wireless adapter uses for identifying connection. Enter the name of computer-to-computer network to create (e.g., samsung) or the name of access point to connect. The network name identifies cases. (capital and lowercase) For the name of access point, check the settings of the access point, or ask your wireless network administrator.
Page 67 3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), encryption level, key index, and wireless security password configured in the access point. It is recommended to configure data encryption for security purposes when creating a computer-to-computer network connection profile.
Page 68 Wireless Network Setup Using the Wireless LAN Setup Program(for an 11b card) You can use a wireless LAN by using a wireless LAN configuration program (PROSet) provided separately. For an 11a/g card, see ”Wireless Network Setup Using the Wireless LAN Setup Program(for an 11a/g and 11g card)”...
Page 69: Security Settings
Configure wireless network settings in PROSet following the procedures below. To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following "To create computer-to-computer (Ad Hoc) network" section.) 1.
Page 70 Network name (SSID) is a name that a wireless adapter uses for identifying connection. Enter the name of computer-to-computer network to create (e.g., samsung) or the name of access point to connect. The network name identifies cases. (capital and lowercase) For the name of access point, check the settings of the access point, or ask your wireless network administrator.
Page 71 - Ad hoc - Connect directly to other computers - Select to create a computer-to-computer (Ad Hoc) network. 3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), key index, and password configured in the access point.
Page 72: Using Network Services
Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet.
Page 73 Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'.
Page 74: Sharing Printers
Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Double-Click My Network Places of desktop under Other Places. 2. Click 'View workgroup computers', and click the desired computer to access the shared file.
Page 75 Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4.
Page 76 5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8.
Page 77 Sharing an Internet connection through a wireless network By connecting your computer to another computer, which is connected to the Internet over a wired connection, through a wireless network (Peer-to- Peer), you can access the Internet from your computer. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network.
Page 78 If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start >...
Page 79: Customizing Your Computer
Customizing Your Computer Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off.
Page 80: Starting System Setup
Starting System Setup To start System Setup, turn on your computer and then press <F2> and hold until the System Setup screen appears. Table 2. System Setup Menus Menu Function Main Changes the basic system. Advanced Configures advanced features on your computer. Security Enables security features, including passwords.
Page 81: Changing Booting Priority
Changing Booting Priority You can select the booting priority among the devices such as the hard drive, CD-ROM drive, etc. The following example describes how to configure the hard drive as the first booting device when the CD-ROM drive is configured as the first booting device by default.
Page 82: Setting The User Password
Do not lose or forget your password. If you have forgotten your password, contact the Samsung service center. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 67.
Page 83: Deactivating The Password
Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. Set the Password on boot option to [Enabled]. From now on, system booting will not proceed without the password. Deactivating the Password 1. On the password to delete, press <Enter>. (e.g. supervisor password) 2.
Page 84: Configuring Resolution And Color Depth
Configuring Resolution and Color Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Color quality is determined by the number of bits used to represent a pixel on the screen. High color quality displays more number of colours on your screen.
Page 85: Using External Display Devices
Using External Display Devices Using external display devices such as monitor or projector, you can view the screen images alternatively or simultaneously. You can extend the screen into two display devices to use larger workspace. Using external display devices would be especially useful when you are giving presentations or watching a video file.
Page 86 To switch display devices using shortcut key You can switch display devices easily by pressing <Fn>+<F4/ > shortcut key. Provided that the CRT monitor is connected, the display order will be LCD > CRT > LCD+CRT whenever the <Fn>+<<F4/ > key is pressed. You cannot use the <Fn>+<F4/ >...
Page 87: System Management
System Management Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance.
Page 88 Everything in memory gets saved to the HDD, and the monitor and hard disk get turned off. By default, the power scheme is configured to SAMSUNG mode. SAMSUNG mode extends the battery life and optimizes the Intel Speedstep function. Since the CPU power consumption is automatically...
Page 89 If You Reinstall Windows: You should re-establish hibernate in power options by opening Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
Page 90 Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2.
Page 91: Using The Battery
Using the Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. Please read the instructions on the battery before use. Please refer to the system operation environment (p114) of this manual and operate and store the battery at room temperature.
Page 92: Monitoring The Battery Charge
Monitoring the Battery Charge You can view the battery charge status by completing the following procedures. To use the shortcut key to view Press the <Fn>+<F2/ > key combination on the keyboard and then the current power source and the current remaining battery charge are displayed at the top left of the screen.
Page 93: Battery Calibration
Using the battery Battery is an expendable supply, so when you use it for a long time, the capacity/battery life is shortened. If the battery life is reduced to under half of the initial time, we recommend that you purchase a new battery to use. Battery Warning You will hear an alarm when the remaining battery charge is under 10%.
Page 94: Using The Security Lock Port
Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use.
Page 95: Tips For Using Your Computer
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis.
Page 96: Handling Spills
Travelling with Your Computer Air Travel If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data.
Page 97: Storing The Computer For Long Periods
Storing the Computer for Long Periods If you will not be using the computer for a long period of time (a month or more), you should discharge the battery completely then remove the battery from the computer. This extends the life of the battery. 84 Users Manual...
Page 98: Troubleshooting
Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device drivers. System Recovery Precaution: Before you start restoring your windows operating system insure you backup all data on your hard drive. Samsung is NOT responsible for any data loss. Troubleshooting 85...
Page 99: Questions And Answers
Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Page 100: Display Related
Display Related Q1 The LCD screen is blank. Adjust the LCD screen brightness. Use the <Fn>+< Q2 The screen saver disturbs screen viewing during Media Player or video file operation. Under the Media Player Tools, Options > Player > Enable Screen Saver During Use, uncheck the box and restart the player.
Page 101 Q7 When I pressed <Fn>+<F4/ resolution is changed. Change the resolution again on [Graphics Controller Properties] dialog. (Refer to ”Using External Display Devices” (p72).) Q8 <Fn>+<F4/ When you are playing a video file such as a video CD, an MPEG file, or a DVD, when no external display is connected, or when you are using the extended desktop mode or full screen DOS mode, you cannot change display devices.
Page 102: Modem Related
Modem Related Q1 I cannot hear the modem sound. Check that the telephone line is properly connected to the modem. Check that the modem driver is installed properly. Click Start > Control Panel > Performance and Maintenance > System. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon.
Page 103 - Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. - Configuring the Modem through the Control Panel Click Start >...
Page 104 In the Modems tab, select the installed modem, and click Properties. In the Power Management tab of the Modem Properties window, select the “With this device, exit the computer from stand-by mode” item and then click OK. The above setting enables the modem to turn on the system and receive a fax when in power saving mode.
Page 105: Wired Lan Related
Wired LAN Related Q1 <Wake On LAN> function <Wake On LAN> is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network (wired LAN). To use <Wake On LAN> function: Select My Network Places >...
Page 106: Wireless Lan Related
Wireless LAN Related Refer to ”Connecting Through a Wireless LAN (Option)” (p42) for the basic uses of a wireless LAN. Q1 The Wireless LAN device is operating properly, but I cannot connect to the Internet or to another computer. This is due to an incorrect configuration, or a configuration error. Check the following check lists: If you are using a computer-to-computer (Ad Hoc) network connection, check that the name of the configured network (SSID) is correct.
Page 107 Q3 I cannot share an Internet connection. It may require some time to synchronize the computers to share an Internet connection after the Internet connection sharing configuration is completed. If you cannot share Internet connection even after a longer period, restart the computer.
Page 108 - Verify whether the AP's firmware is the most recent version. (Contact the AP manufacturer or the place where you purchased the AP for details of the AP firmware.) Verify whether the AP has been properly connected to the network. Verify whether the network is operating normally by connecting the wired network cable, which has been connected to the AP, to your computer.
Page 109 disable the [View Available Wireless Networks] window supported by WZC service. Exit the wireless LAN related program then check whether the window is enabled. Initialize the device driver. Click Start > Control Panel > Performance and Maintenance > System > Hardware tab >...
Page 110 Q7 When using a computer-to-computer (Ad Hoc) network, sometimes I cannot search the access point. It may happen occasionally when you are using a computer-to-computer (Ad Hoc) network connection. Even if you cannot find some access points, the computer-to-computer (Ad Hoc) network is operating properly. Click Refresh to view the latest search result.
Page 111 Check the properties of the AP in the wireless network settings. If the ’Use IEEE 802.1x authentication in this network’ option is selected, deselect the option on the Authentication tab. For more detailed information about authentication server, ask your network administrator.
Page 112: Games And Programs Related
Games and Programs Related Q1 3D game is not executed, or some functions are not working. Change the graphic setting of the game to '2D' or 'Software Renderer', then execute the program again. Q2 I launched a game right after installing it, and the game is not executed. This problem may occur when the game is not compatible with Windows XP.
Page 113 Q6 The running speed of a game is too slow or fast. Change the setting of Power Schemes to 'Always On'. (Click Start > Control Panel > Performance and Maintenance > Power Options > Power Schemes tab, then configure the Power schemes field to 'Always On'.) Q7 When I pressed <Fn>+<F10 or F11>...
Page 114: Security Center
Security Center Q1 To change the popup window display settings when connected to the Internet. In the Windows XP SP2 environment, you can decide whether to display a popup window when connected to the Internet, for user convenience and security. To display most of the popup windows when connected to the Internet: Click on Internet Options in Start >...
Page 115 Q3 When you see a Windows Security Alert icon ( of the task bar. With the Security Center feature added, Windows XP SP2 checks the Firewall, the automatic updates configuration and installation of virus-checking programs to display a Windows Security Alert icon on the right part of the task bar when it judges that the computer is vulnerable to attacks from the Internet.
Page 116 If Windows does not recognize the existence of an anti-virus program even when it has been installed, your computer could be vulnerable to attacks from the Internet. You should install an anti-virus program that your computer is able to identify. Check the following programs which Windows can detect and select one from the list.
Page 117: Restoring The System
Restoring the System This description is only for models running Window XP. The System Restore function allows you to restore your computer to an earlier copy (called restore point), and restores the settings if a problem occurs.The System Restore function is provided by Windows XP to enable the resolution of various problems without reinstalling Windows XP completely.
Page 118: Returning Your Computer To An Earlier Restore Point
2. Select "Create a restore point", and click Next. Since changes made after the Recovery Point may not be maintained, please back-up all necessary files to another location before performing system recovery. 3. In the Restore point description box, type a name to identify the restore point, and than click Create.
Page 119 2. Select "Restore my computer to an earlier time", and then click Next. 3. Select the desired restore date from the calendar restoration and select the desired restore point from the list, and then click Next. The date of the restore point is displayed in bold font. 4.
Page 120: Undoing The Last Restoration
5. After the restoration is complete, Windows restarts. In the [System Restore completed] dialog, click OK.Your computer has been restored to the selected restore point. Undoing the last restoration The procedures to undo a restoration are described below. 1. Click Start > All Programs > Accessories > System Tools > System Restore. 2.
Page 121: Reinstalling Software
Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. This computer is optimized for Microsoft Windows XP, therefore driver other than the ones included in the System Software CD are not provided.
Page 122: Installing Drivers And Programs
Installing drivers and programs 1. Click Standard Installation in the main window of the System Software CD. (Standard Installation is recommended) 2. The system is scanned to display the drivers and programs that need to be installed. 3. Click OK. The drivers and programs are automatically installed as factory defaults.
Page 123: Reinstalling Windows Xp
Reinstalling Window may delete the data on the hard disk drive such as files, programs, etc. In order to minimize damage from data loss, please remember to always back up data. Samsung Electronics is not liable in the case of data loss, please consult your warranty statement for clarification.
Page 124 • Standard installation: You can change the settings for partitioning, the installation folder, etc. during the Windows installation. However, reinstalling Windows may delete the data on the hard disk drive such as files, programs, etc. In order to minimize damage from data loss, please remember to always back up data.
Page 125 8. When a window that requires your name and organization pops up, enter your name and the organization and click Next. In the Windows XP Professional edition, an additional window that requires the computer name and the administrator password appears. Enter the computer name and the administrator password and click Next.
Page 126 If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option.
Page 127: System Specification
Specifications System Specification The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification Intel Pentium M ULV 1.1~1.2GHz Intel Celeron M ULV 900MHz~1.0GHz Cache memory 2MB / 512KB L2 cache Main memory On board 256 DDR SDRAM (An additional 128/256/512/1024 MB module can be installed, 1DDR socket)
Page 128: Product Specification
Wireless LAN Specification (Optional) Intel(R) PRO/Wireless 2200BG Network Connection Product Specification Item Physical Dimensions Specifications operation temperature and humidity Power Specification Power Saving Mode Receiving Mode Transmission Mode Power Network Compatibility Specifications Operating System Media Access Protocol Security * This piece of equipment supports the Wi-Fi wireless LAN security standard, WPA (Wi-Fi Protected Access) and CCX (Cisco Compatible eXtensions).
Page 129 PROSet may be required depending on the network settings. For driver update, visit www.samsung.com and for information on the PROSet installation, refer to ”Wireless Network Setup Using the Wireless LAN Setup Program(for an 11a/g and 11g card)” (p51). For more information, ask your network administrator.
Page 130: Channel Allocation
Radio Specifications RF Band Support Channels Device Standard Output Power Transmission Method Transmission Rate (Mbps) * Antenna Type * The transmission rate may differ from the actual transmission rate. ** 11a mode is supported only when the device is connected with an IEEE802.11a device (e.g. IEEE802.11a compatible Access Point).
Page 131 LAN driver have to be installed on your computer, and certificates or PROSet may be required depending on the network settings. For driver update, visit www.samsung.com and for information on the PROSet installation, refer to ”Wireless Network Setup Using the Wireless LAN Setup Program(for an 11b card)”...
Page 132 Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.11b •...
Page 133 Abbreviations A ..Amperes AC ..Alternating current ACPI ..Advanced Configuration and Power management Interface APM ..Advanced Power Management ATA.
Page 134 ISA ..Industry Standard Architecture KB ..Kilobytes kg ..Kilograms LAN..Local-area network lb..
Page 135 Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
Page 136 CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts).
Page 137: Hard Drive
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer.
Page 138 PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed.
Page 139 Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer.
Page 140: Getting Started
SAMSUNG Q30 BA68-02721A11 041120 Chapter 1 Chapter 1 Getting Started This chapter provides basic information for using this computer. System overview and methods for general use are provided.
Page 141: Introducing The Computer
Introducing The Computer Front View LCD Panel Keyboard Memory Card Slot Manual Status Lights Touchpad Touchpad (LED) Button...
Page 142: Right View
Right View Power Button CF Card Slot USB 2.0 Port Network(LAN) Port Modem port Left View 1394 Port (6Pin) Microphone Jack DC-In Port Moniter Port USB 2.0 Port Headphone / S/PDIF Jack(Optical) Chapter 1. Getting Started...
Page 143: Rear View
Rear View Battery Security Lock Port Bottom View Battery Latches 3D Speaker Manual...
Page 144 Turning the Computer On and Off Turning On 1. Insert the battery and connect the power according to the supplied Installation Guide. 2. Lift up the LCD panel and open it to a comfortable angle. 3. Press and then release the power button to turn the system on. Since opening the LCD panel by hand might cause damage to the panel, please use both hands when opening the panel.
Page 145: Changing Users
Creating and Changing User Accounts Multiple users can be registered in a single system so that each user may use their own customized working environment. Procedures to register and change user accounts are provided below. ■ Registering a new user 1.
Page 146 Touchpad Movement of the pointer (arrow) on the screen will correspond to movement made with a finger on the touchpad. Locking the touchpad You can lock the touchpad and use only the keyboard and mouse. To lock the touchpad function, press the <Fn>+<F9> key combination. ■...
Page 147: Using The Touchpad Scroll Function
■ Drag (Move / Select) Drag and drop a part to the required place. ■ Using the Touchpad Scroll Function The touchpad has a scroll function, which can be used like the wheel dial of a wheel mouse. Move up and down along the right edge of the touch pad (scrolling up and down) or left and right along the bottom edge of the touch pad (scrolling left and right) to scroll the screen.
Page 148: Special Function Keys
Using the Keyboard Function Keys <Fn> Key Numeric Keypad ■ Special Function Keys: Key Com- binations Name REST Puts the computer into suspended mode.To use the computer again, press the power button. Gauge Shows the current power source and the remaining battery charge. LCD/CRT Switches the display between the LCD and an external display device when an external display device is connected.
Page 149 Key Com- binations 1-10 Manual Function Name Turns the wireless LAN service on and off for appropriate models. Wireless Turns the touchpad function on and off. Touchpad Num Lock Puts the computer into suspended mode. To use the computer again, press the power button.
Page 150: Status Indicators
Status Indicators Shows the operating status of the computer. Icon Name Num Lock Turns on when the numeric keypad is activated. Caps Lock Turns on when all alphabet characters you type will be in upper case. Scroll Lock Turns on when it is set to scroll the screen up and down while the cursor position does not change in some applications.
Page 151 Maintaining your LCD brightness settings after turning the system off and on 1. Turn the system on. When the Samsung Logo appears, press the <F2> key to enter Setup. 2. In the Boot menu, change the Brightness Control Mode option to User Control.
Page 152: Adjusting The Volume
Adjusting the Volume ■ To adjust using keyboard Press < >+< > or < >+< ■ Using the Volume Control Program On the taskbar, click the Volume ( For advanced volume control options, double-click the Volume ( adjust the settings in the [Master Volume] dialog. When you turn the system on, a booting noise may occur.
Page 153: Proper Seating Posture During Computer Use
Proper Seating Posture During Computer Use The proper seating posture during computer use is provided here. Maintaining proper posture during computer use enhances performance and prevents physical bodily harm. Seating Posture - Position the chair so that the eyes are slightly higher than the display - Straighten the neck and back.
Page 154 Chapter 2 Chapter 2 Introducing Windows This chapter provides basic information on using the computer’s main operating system Windows.
Page 155: Windows Xp Basics
SAMSUNG P10 Windows XP Basics Windows is the computer’s main operating system, which needs to be familiarized with in order for efficiently computer use. Windows XP Tour A tour of the elementary functions provided by Windows XP. Click Start > Tour Windows XP.
Page 156 Understanding the Desktop The Desktop is the working area on the computer. It consists of the large workspace, which is more or less the entire the screen and a Taskbar at the bottom. Desktop Icons You can directly launch a program. Start Menu Start Button Start Button...
Page 157 Understanding the Start Menu The Start Menu includes everything that is required to start Windows. From the Start Menu it is possible to run a program, open a file, assign system users with the Control Panel, receive support by clicking Help and Support, and search desired items from computer or Internet by clicking Search.
Page 158 Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer’s hard drive, will be used as an exam- ple here to show the basic composition of a window. Click Start >...
Page 159 Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Displays Help Index Related help information appears when a search keyword is entered. Help Topics Troubleshooting Information Manual Connect to Support Center.
Page 160: Document Operations
Document Operations To create documents, WordPad or NotePad, which is included in Windows, or a separate specialized word processor program can be used, such as MS Word. Instructions for creating documents using WordPad is provided here. ■ Creating a New Document 1.
Page 161: Opening A Document
■ Opening a Document 1. Click Start > All programs > Accessories > WordPad. 2. Select File From the Menu, and click Open. 3. Click on the Look in field and specify the folder in which the file is saved. 4.
Page 162: Using The Computer
Chapter 3 Chapter 3 Using The Computer This chapter investigates various different functions of the computer and provides information on using the related application programs for them.
Page 163: Using The Cd Drive
Using the CD Drive For this computer, a 1394 external CD-RW/CD-ROM combo or DVD multi drive is provided. ■ Connecting a CD drive Connect the CD drive to the 1394 port. ■ To Run a CD 1. Push the eject button on the CD drive. Status Indicator 2.
Page 164: Using The Windows Media Player
Using the Windows Media Player The Windows Media Player enables the user to configure and play video and audio files from the computer or the Internet. Click Start > Windows Media Player. Or click Start > All Programs > Accessories > Entertainment > Windows Media Player.
Page 165: To Play An Audio Cd
To Play an Audio CD 1. Insert an audio CD into the CD drive, and a list of all available players is displayed automatically. 2. Select Windows Media Player, and click OK to play the audio CD. To Play a Video CD 1.
Page 166: To Write Data In Cd
To Write Data in CD If your computer has CD-RW functionality, you can copy data to a blank CD or cre- ate an audio CD. An additional CD writing program is supplied in an additional CD. 1. Insert a blank CD into the CD-RW drive. 2.
Page 167 4. Select, drag and drop folders or files to copy onto the CD-ROM drive window. Click Write Files to CD in the CD-ROM drive window. 2. Click Write Files to CD 5. When the CD Write Wizard appears, enter the CD label, and click Next. The data will begin copying.
Page 168: Enjoying Home Theater
Enjoying Home Theater This product supports 5.1 channel output, which is a basic function for home theater systems, and DVD drives. It provides 3D surround- ing sound and vivid screen. Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and digital amp and provides a high-resolution screen (MPEG2) and 3D sur- rounding sound (Dolby 5.1 or DTS).
Page 169 ■ Step 2. Configure digital sound output on the computer 1. Click Start > Control Panel > Sounds, Speech and Audio Devices > Sounds and Audio Devices. 2. In the Device volume field on the Volume tab, click Advanced. 3. In the [Master Volume] dialog, click Option > Advanced Controls. Then Advanced button is displayed on the bottom of the dialog.
Page 170 Using Memory Card Slot Through the memory card slot, you can use memory cards such as memory stick, SD (Secure Digital) memory card, and MMC (Multi Media Card). You can use the memory cards as a removable disk, and use them to exchange data between your computer and digital devices such as a digital camera.
Page 171 2. Click Start > My Computer. The inserted memory card is displayed. 3. You can write data to the memory card. If the memory card is not formatted yet, format the memory card before use. To remove a memory card 1.
Page 172 Using the CF Card Slot You can insert a CF card, used in multimedia devices such as digital cameras, into the CF card slot and exchange data between the CF card and the computer. 1. Insert a CF card into the CF card slot at the side of the system. CF Card Slot If you insert a CF card, the Removable Disk window appears and you can use the CF card.
Page 173 1. Click Start > All Programs > Samsung > Samsung Smart Screen. 2. Samsung Smart Screen appears. When you run the program for the first time, water drop image is displayed. 3. To move an icon, click a water drop to open it, then drag an icon to another water drop.
Page 174 Using Samsung Theme Samsung Theme is a program that enables a user to easily switch a theme (desktop, logon screen and sound effect). Double-click the Samsung Theme ( (Or select Start > All Programs > Samsung > Samsung Theme >...
Page 175 3-14 Manual...
Page 176: Connecting To The Internet
Chapter 4 Chapter 4 Connecting to the Internet This chapter provides instructions on connecting to the Internet.
Page 177 Connecting to the Internet The following options show many ways to connect to the Internet. An appropriate option should be selected depending on the user’s working environment and the user’s system specifications. Option 1 Connecting using a modem and a telephone line Option 2 Connecting using a High-speed communication Option 3 Connecting using a wired LAN Option 4 Connecting using a wireless LAN...
Page 178: Connecting To The Internet Using A Modem
Connecting to the Internet Using a Modem 1. Connect the telephone line to the modem port. Do not use a digital telephone line. 2. To connect the modem to the Internet, and use e-mail, you have to apply to an Internet Service Provider (ISP) for an Internet service.
Page 179: Configuring The Network Environment Settings For Wired Lan Connections
Configuring the Network Environment Settings for Wired LAN Connections A wired LAN environment is an environment where you can connect to the Internet using the company’s LAN or with a broadband modem. 1. Connect the network (LAN) cable to the LAN port of the system. 2.
Page 180 7. In the “This connection uses the following items” field, select Internet Protocol (TCP/IP), and click Properties. In the above screen, necessary network components can be added by clicking the Install button. 8. Enter the system’s IP and DNS server addresses on the General tab of the [Internet Protocol (TCP/IP) Properties] window.
Page 181 1. Connect LAN cable to the computer’s LAN port. 2. Double-click Samsung Network Manager icon on the desktop. Or click Start > All Programs > Samsung Network Manager > Samsung Network Manager. 3. When you are using DHCP, available IP’s are displayed in the status dialog box.
Page 182 To change network places You can change network places as below. 1. Connect LAN cable to the computer’s LAN port, and double-click Samsung Network Manager icon on the desktop. If you used static IP in previous place, previous static IP is displayed in the status dialog box.
Page 183: Using Both Dhcp And Static Ip Simultaneously
Using Both DHCP and Static IP Simultaneously. When you are alternatively using networks with either DHCP or static IP addressing, you can use alternative settings that enable simultaneous configurations of DHCP and static IP to use both of the network connections without reconfiguring. This function is provided only when your operating system is Windows XP.
Page 184: Access Point
Configuring the Network Environment Settings for Wireless LAN Network A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. When a computer-to-computer network has been constructed, a computer that is not connected to the Internet can share the Internet by accessing another computer connected to the Internet.
Page 185: Connecting To An Access Point
Connecting to an Access Point This section describes how to connect to an AP. You can use the network when you are connected to an AP. 1. Right-click on the Wireless Network Connection ( and select View Available Wireless Networks. 2.
Page 186 Connecting to computer-to-computer networks (peer-to-peer or ad hoc) In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules. Using this method, a computer that is not connected to the Internet can share the Internet by accessing another computer connected to the Internet.
Page 187 Select ‘Computer-to-computer (ad hoc) networks only’, and click Close. 5. In the Wireless Networks tab, click Add. 6. Enter the network name (e.g. samsung), and unselect ‘The key is provided for me automatically’. Enter the encryption key in the Network key field, and click OK.
Page 188 7. Check that the configured network name (e.g. samsung) is in the ‘Preferred net- works item’, and click OK. Now your wireless network setup has been completed. Chapter 4. Connecting to the Internet 4-13...
Page 189 1. Right-click on the Wireless Network Connection ( and select View Available Wireless Networks. 2. Select the wireless network name (e.g. samsung) specified in “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)”, and click Connect. 3. Enter a cryptographic key in the network key box and click Connect.
Page 190 Wireless Network Setup Using the Wireless LAN SetupProgram(for an 11a/g and 11g card) You can use a wireless LAN by using a wireless LAN configuration program (PROSet) provided separately. For an 11b card, see P. 4-18 Wireless Network Setup Using the Wireless LAN Setup Program(for an 11b card) To use wireless network connection, complete the following procedures.
Page 191 In Available Networks, click on Refresh. 2. Select the name of desired access point or computer-to-computer network to connect from the searched available networks list, and click Configure. 3. Enter Profile Name and click Next. 4. In the Search Security Settings window, the wireless network security search message will appear.
Page 192 Network name (SSID) is a name that a wireless adapter uses for identifying connection. Enter the name of computer-to-computer network to create (e.g., samsung) or the name of access point to connect. The network name identifies cases. (capital and lowercase) For the name of access point, check the settings of the access point, or ask your wireless network administrator.
Page 193 Wireless Network Setup Using the Wireless LAN Setup Program(for an 11b card) You can use a wireless LAN by using a wireless LAN configuration program (PROSet) provided separately. To use wireless network connection, complete the following procedures. ▶ Step1. Install the wireless LAN configuration program (PROSet). ▶...
Page 194 1. Click Scan in the Networks tab. 2. Select the name of desired access point or computer-to-computer network to connect from the searched available networks list, and click Connect. If your desired network does not appear, click Refresh. An access point is represented by ( is represented by ( ) icon.
Page 195 Network name (SSID) is a name that a wireless adapter uses for identifying con- nection. Enter the name of a computer-to-computer network (e.g. samsung) or the name of the access point to connect to. The network name identifies cases. (capi- tal and lowercase) For the name of access point, check the settings of the access point, or ask your wireless network administrator.
Page 196 Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet.
Page 197 ■ Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click ‘IF you understand the security risks but want to share files without running the wizard, click here’. 3.
Page 198 ■ Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer.
Page 199 Sharing Printers This section describes how to share a printer between computers connected to a net- work. To share a printer, complete the following procedures: ▶ Step 1. Configure printer sharing in the computer connected to the printer. ▶ Step 2. Add and use the shared printer in other computers on the network. ■...
Page 200 4. In the Printers and Faxes window, you will find the printer icon has been changed to another icon on a hand. ■ Step 2. Adding and Using a Shared Printer 1. From a different computer that wants to use the shared printer, click Start > Printers and Faxes.
Page 201 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8. Select Yes for ‘Do you want to use this printer as a default printer?’, and click Next. 9. Click Finish. 10. When the printer sharing configuration has been completed, the shared printer appears in the Printers and Faxes window.
Page 202: Wireless Network
Sharing an Internet connection through a wireless network By connecting your computer to another computer, which is connected to the Internet over a wired connection, through a wireless network (Peer-to- Peer), you can access the Internet from your computer. To share an Internet connection, the computers should be connected to a comput- er-to-computer (peer-to-peer) wireless network.
Page 203 3. In the Advanced tab, select ‘Allow other network users to connect through this computer’s Internet connection’, and click OK. ■ Step 2. Checking the Shared Internet Connection When the Internet connection sharing configuration has been completed, the net- work icon in the Network Connections window is displayed as follows: Click Start >...
Page 204: System Management
Chapter 5 Chapter 5 System Management This chapter provides information on efficient computer management.
Page 205: Managing Power
Power Options > Power Schemes tab. Then specify time in each item and click OK. By default, the power scheme is configured to SAMSUNG mode. SAMSUNG mode extends the battery life and optimizes the Intel Speedstep function. Since the CPU power consumption is automatically optimized to conserve power when the computer is operating on battery power, an application may be executed slower than when it is operating on AC power.
Page 206: Using The Power Button
Using the Power button You can configure the function of the power button. Click Start > Control Panel > Performance and Maintenance > Power Options and select the Advanced tab. When the Power button is configured to put the system into Power-Saving Mode, man- ually shutting down the computer requires the Power button to be pressed and held for more than 4 seconds.
Page 207 Using the Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. This computer uses smart rechargeable Lithium-Ion (Li-Ion) battery. Ejecting and Attaching Battery 1. Shutdown system and close LCD. 2. Put the computer upside down. 3.
Page 208 Monitoring the Battery Charge You can view the battery charge status by completing the following procedures. ■ Using the shortcut key to view Press the < > + < > key combination on the keyboard and then the cur- rent power source and the current remaining battery charge are displayed at the top left of the screen.
Page 209: Increasing Battery Life
Increasing Battery Life ■ Adjust LCD Brightness Press the < brightness. ((p. 1-12) For more information about how to adjust the screen brightness, refer to.) ■ Use Power Saving Mode This function reduces power consumption when the system is not being used for a prolonged period of time.
Page 210: Using The Security Lock
Using the Security Lock The security lock is a device used to physically ‘fix’ the system when using it in a pub- lic place. The locking device needs to be purchased separately. The shape and meth- ods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use.
Page 211: Traveling With The Computer
Traveling with the Computer When traveling, keep the system and the AC adapter disconnected. Otherwise, it may affect the functions of the system. Make sure that the system is not pressed by a book or heavy objects. The LCD may get damaged. When traveling by plane, use a bag designed for notebook PCs and hand-carry the computer.
Page 212: Customizing Your Computer
Chapter 6 Chapter 6 Customizing your computer This chapter provides information how to use the system setup, customizinig screen settings.
Page 213: To Enter System Setup
Using System Setup System Setup is a utility that enables the computer environment to be changed to suit the user. System Setup is used when changing the system password, booting priority, or when adding new devices. Please use extra care when configuring System Setup, as it may cause serious system error.
Page 214: System Setup Menus
System Setup Menus Menu Items Description Main Configures the basic system environment Advanced Configures OS and major chipset options of the system Security Configures system security options Boot Configures booting options Exit Exits System Setup For more information on System Setup menus or options, please refer to Help on the right side of the screen.
Page 215: Configuring The Password
By configuring a supervisor password, you can restrict system access to autho- rized users only. Do not lose or forget your password. If you have forgotten your password, contact the Samsung service center. 1. Select the Security menu in the System Setup. (To enter into System Setup, see Page 6-2.) 2.
Page 216 ■ Setting the User Password You can configure user passwords so that other users can use the system. Before configuring a user password, a supervisor password must have been con- figured. Users can start the system with their user password, but cannot enter into the System Setup.
Page 217 Changing Booting Priority You can select the booting priority among the devices such as the hard drive, CD-ROM drive, etc. The following example describes how to con- figure the hard drive as the first booting device when the CD-ROM drive is configured as the first booting device by default.
Page 218 Configuring Resolution and Color Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Color quality is determined by the number of bits used to represent a pixel on the screen.
Page 219 Using External Display Devices Using external display devices such as monitor or projector, you can view the screen images alternatively or simultaneously. You can extend the screen into two display devices to use larger workspace. Using external display devices would be especially useful when you are giving presentations or watching a video file.
Page 220 Monitor Displays on an external device such as monitor or a projector. Notebook Displays on the notebook LCD only. Displays the same screen on the notebook LCD, and an Intel(R) Dual external device such as monitor or projector. Display Clone Extended Desktop Extends the screen into the notebook LCD and an external device such as monitor or projector to use a 2 times larger...
Page 221: Checking For Viruses
Checking for Viruses The Norton AntiVirus software is provided as the virus inspection program. 1. Select Start > All Programs > Norton AntiVirus > Norton AntiVirus 2003. 2. Click Scan Virus, select drive to inspect, and click Scan. 3. If a virus is detected, select Automatic in Norton AntiVirus, and click Next to delete the virus.
Page 222: Recovering The Computer
Chapter 7 Chapter 7 Recovering the Computer This chapter provides recovery procedures using the System Recovery CD when the computer is not operating properly.
Page 223 Restoring the System The System Restore function allows you to restore your computer to an earli- er copy (called restore point), and restores the settings if a problem occurs. The System Restore function is provided by Windows XP to enable the reso- lution of various problems without reinstalling Windows XP completely.
Page 224 ■ Returning your computer to an earlier restore point The procedures to return your computer to an earlier restore point when a problem has occurred are described below. 1. Start > All Programs > Accessories > System Tools > System Restore. 2.
Page 225 Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and pro- gram using the system software CD. ■ Running the system software CD Insert the system software CD into the CD-ROM drive. The initial screen appears automatically.
Page 226 ■ Installing drivers and programs 1. Click Standard Installation in the main window of the System Software CD. (Standard Installation is recommended) 2. The system is scanned to display the drivers and programs that need to be installed. 3. Click OK. The drivers and programs are automatically installed as factory defaults.
Page 227 Reinstalling Window may delete the data on the hard disk drive such as files, programs, etc. In order to minimize damage from data loss, please remember to always back up data. Samsung Electronics is not liable in the case of data loss, please consult your warranty statement for clarification.
Page 228 Quick Installation : This re-installs Windows with the user data and the system configuration intact. The user data in the already existing Windows folders may be preserved as the existing Windows folders are overwritten. 3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while.
Page 229 ■ If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option.
Page 230 Q&A This section provides information on possible problems, solutions and other references for system use. Windows Related Q1The system does not shutdown properly. A When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Page 231 Display Related Q1The LCD screen is blank. A Adjust the LCD screen brightness. Use the <Fn> + < Q2 The screen saver disturbs screen viewing during Media Player or video file operation. A Under the Media Player Options, in Player > Enable Screen Saver During Use, uncheck the box and restart the player.
Page 232 Q7 When I pressed <Fn>+< screen resolution is changed. A Change the resolution again on [Graphics Controller Properties] dialog. ((P. 6-8) Refer to ‘Using External Display Devices’.) Q8 <Fn>+< > keys do not operate. A When you are playing a video file such as a video CD, an MPEG file, or a DVD, when no external display is connected, or when you are using the extended desktop mode or full screen DOS mode, you cannot change display devices.
Page 233 Modem Related Q1I cannot hear the modem sound. A1 Check that the telephone line is properly connected to the modem. A2 Check that the modem driver is installed properly. 1. Click Start > Control Panel > Performance and Maintenance > System.
Page 234 Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. Configuring the Modem through the Control Panel 1.
Page 235 Wired LAN Related Q1 <Wake On LAN> Function. A <Wake On LAN> is a function that activates the system in rest mode when a sig- nal (such as ping or magic packet commands) arrives from network(wired LAN). To use <Wake On LAN> function 1.
Page 236 Wireless LAN Related Refer to (P.4-9) “Configuring the Network Environment Settings for Wireless LAN Network (WLAN)” for the basic uses of a wireless LAN. Q1 The Wireless LAN device is operating properly, but I cannot connect to the Internet or to another computer. This is due to an inappropriate configuration.
Page 237 Q3 I cannot share an Internet connection. A1 It may require some time to synchronize the computers to share an Internet connection after the Internet connection sharing configuration is completed. If you cannot share Internet connection even after a longer period, restart the computer. A2 Check if the connection between the network adapters is configured to bridge.
Page 238 A5 Verify whether the AP has been properly connected to the network. Verify whether the network is operating normally by connecting the wired network cable, which has been connected to the AP, to your computer. A6 Check the network key settings (encryption key). When automatic code conversion (a passphrase function) has been selected and data communication is not functioning even with a normal wireless connection, it is recommended entering the network key (encryption key) manually.
Page 239 A3 Initialize the device driver. Click Start > Control Panel > Performance and Maintenance > System > Hardware tab > Device Manager > Network adapters, and select the wireless LAN adapter. Right-click the network adaptor and select 'Disable' from the popup menu. Then right-click over the network adaptor and select 'Enable' after a short wait to check that the device is operating properly.
Page 240 Q7 When using a computer-to-computer (Ad Hoc) network, sometimes I cannot search the access point. A It may happen occasionally when you are using a computer-to-computer (Ad Hoc) network connection. Even if you cannot find some access points, the computer-to-computer (Ad Hoc) network is operating properly. Click Refresh to view the latest search result.
Page 241 A3 If the AP is configured to ‘Use network authentication (Shared Key)’ If the AP is configured to authentication shared mode, all computers to be con- nected should be configured as follows: If you are using Windows XP, select network authentication(shared mode) in the wireless network settings.
Page 242: Game/Program Related
Game/Program Related Q13D game is not executed, or some functions are not working. A Change the graphic setting of the game to ‘2D’ or ‘Software Renderer’, then exe- cute the program again. Q2I launched a game right after installing it, and the game is not executed.
Page 243 Q7 When I pressed <Fn>+<F10 or F11> keys while playing a game, the computer does not operate properly. A Do not press <Fn>+<F10 or F11> keys while playing a game, since it may cause a system error. Q8 When I played 'The Sims: House Party' game in Dual Display Clone mode, a mouse afterimage is displayed.
Page 244 Security Center Q1 To change the popup window display settings when connected to the Internet. In the Windows XP SP2 environment, you can decide whether to display a popup window when connected to the Internet, for user convenience and security. A1 To display most of the popup windows when connected to the Internet: 1.
Page 245 Q3 When you see a Windows Security Alert icon appear on the right part of the task bar. With the Security Center feature added, Windows XP SP2 checks the Firewall, the automatic updates configuration and installation of virus-checking programs to display a Windows Security Alert icon on the right part of the task bar when it judges that the computer is vulnerable to attacks from the Internet.
Page 246 A5 If Windows does not recognize the existence of an anti-virus program even when it has been installed, your computer could be vulnerable to attacks from the Internet. You should install an anti-virus program that your computer is able to identify. Check the following programs which Windows can detect and select one from the list.
Page 247 Appendix Appendix Appendix System specifications, software types and safety instructions are provided here.
Page 248: System Specifications
System Specifications The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Intel Pentium M ULV 1.1~1.2GHz / Intel Celeron M ULV 900MHz~ 1.0GHz Cache memory 2MB / 512KB L2 cache Main memory On board 256 DDR SDRAM (An additional 128/256/512/1024 MB module can be installed, 1DDR socket)
Page 249: Wireless Lan Specifications
PROSet may be required depending on the network settings. For driver update, visit www.samsung.com and for information on the PROSet installation, refer to P.4-18 ”Wireless Network Setup Using the Wireless LAN Setup Program” . For more information, ask your network administrator.
Page 250: Network Connection
Intel(R) PRO/Wireless LAN 2915 ABG Network Connection Item Physical Specifications Power Specification Network Specifications * This piece of equipment supports the Wi-Fi wireless LAN security standard, WPA (Wi-Fi Protected Access) and CCX (Cisco Compatible eXtensions). To connect to a wireless network consisting of the WPA and CCX certificates or PROSet may be required depending on the network settings.
Page 251 Intel(R) PRO/Wireless 2200BG Network Connection Item Physical Dimensions Specifications operation temperature and humidity Power Saving Mode Power Receiving Mode Specification Transmission Mode Power Compatibility Operating System Network Specifications Media Access Protocol Security * This piece of equipment supports the Wi-Fi wireless LAN security standard, WPA (Wi-Fi Protected Access) and CCX (Cisco Compatible eXtensions).
Page 252: Registered Trademarks
Copyright Samsung Co., Ltd. owns the copyright to this manual. No part of this manual may be reproduced or transmitted in any form or by any means, electronically, mechanically, or through audio, without the consent of Samsung Co., Ltd. The information in this document is subject to change without prior notice.
Page 253: Safety Instructions
Safety Instructions Instructions for Setup ● Set up the system on a stable work surface. If the system is dropped it may be damaged or it may inflict injuries on the user. ● Do not use loose power outlets or damaged power cables.
Page 254 Instructions for careful handling ● Handle with care so as not to damage the data in the hard disk. - Since the hard disk is fragile and sensitive to external conditions, it may be damaged from temperature changes or impact during operation.
Page 255 ● Use only authorized parts and do not disassemble, repair or modify the computer unless at an authorized dealer. Use authorized service centers as the system may be damaged. ● Do not touch the power strip with wet hands. There is a danger of electric shock. ●...

This manual is also suitable for:

Np-q30plus

Samsung NP-Q30 User Manual

Quick Links

Related Manuals for Samsung NP-Q30

Summary of Contents for Samsung NP-Q30

This manual is also suitable for:

Table of Contents