Table of Contents
Advertisement
GETTING STARTED GUIDE
NI PXIe-4140/4141/4142/
4143/4144/4145
Four-Channel SMU
Note
Before you begin, install and configure your chassis and controller.
This document explains how to install, configure, and test the
NI PXIe-4140/4141/4142/4143/4144/4145 (NI 414x). The NI 414x is a four-channel source
measure unit (SMU).
To access NI 414x documentation, navigate to Start»All Programs»National Instruments»
NI-DCPower»Documentation.
Caution
manner not described in this document.
Contents
Electromagnetic Compatibility Guidelines............................................................................... 2
Verifying the System Requirements..........................................................................................2
Unpacking the Kit..................................................................................................................... 2
Kit Contents.............................................................................................................................. 3
Other Equipment............................................................................................................... 3
Preparing the Environment....................................................................................................... 4
Safety........................................................................................................................................ 4
Installing the Software.............................................................................................................. 4
Installing the NI 414x............................................................................................................... 5
Configuring the NI 414x in MAX.............................................................................................6
Programming the NI 414x.........................................................................................................7
Troubleshooting........................................................................................................................ 8
What Should I Do if the NI 414x Doesn't Appear in MAX?............................................8
What Should I Do if the Module Fails the Self-Test?.......................................................8
Why Is the ACCESS LED Off When the Chassis Is On?.................................................8
Where To Go Next.................................................................................................................... 9
Worldwide Support and Services............................................................................................ 10
You can impair the protection provided by the NI 414x if you use it in a
Advertisement
Table of Contents
Related Manuals for National Instruments NI PXIe-4140
Summary of Contents for National Instruments NI PXIe-4140
-
Page 1: Table Of Contents
Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the NI PXIe-4140/4141/4142/4143/4144/4145 (NI 414x). The NI 414x is a four-channel source measure unit (SMU). To access NI 414x documentation, navigate to Start»All Programs»National Instruments»... -
Page 2: Electromagnetic Compatibility Guidelines
Electromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable protection against harmful interference when the product is operated in the intended operational electromagnetic environment. This product is intended for use in industrial locations. -
Page 3: Kit Contents
A PXI Express embedded controller or MXI controller system that meets the system requirements specified in this guide and chassis documentation. Optional Items • NI screwdriver (part number 781015-01). NI PXIe-414x Getting Started Guide | © National Instruments | 3... -
Page 4: Preparing The Environment
Preparing the Environment Ensure that the environment you are using the NI 414x in meets the following specifications. Operating Environment Ambient temperature range 0 °C to 55 °C (Tested in accordance with IEC 60068-2-1 and IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2 high temperature limit.) Relative humidity range... -
Page 5: Installing The Ni 414X
Ensure that the ejector handle is in the unlatched (downward) position. Place the module edges into the module guides at the top and bottom of the chassis. Slide the device into the slot until it is fully inserted. NI PXIe-414x Getting Started Guide | © National Instruments | 5... -
Page 6: Configuring The Ni 414X In Max
Figure 3. Module Installation 1. Chassis 2. Hardware Module 3. Ejector Handle in Down (Unlatched) Position Latch the module in place by pulling up on the ejector handle. 10. Secure the device front panel to the chassis using the front-panel mounting screws. Note Tightening the top and bottom mounting screws increases mechanical stability and also electrically connects the front panel to the chassis, which can... -
Page 7: Programming The Ni 414X
Microsoft Visual C and C++ with installed C/C++ topic of the NI DC Power Supplies examples. and SMUs Help to manually add all required include and library files to your project. NI PXIe-414x Getting Started Guide | © National Instruments | 7... -
Page 8: Troubleshooting
Select Start»Control Panel»System»Hardware»Device Manager. If you are using a PXI or PXI Express controller, verify that a National Instruments entry appears in the system device list. Reinstall NI-DCPower and the device if error conditions appear in the list. If you are using an MXI controller, right-click PCI-to-PCI Bridge, and select Properties from the shortcut menu to verify that the bridge is enabled. -
Page 9: Where To Go Next
SMUs Help* DISCOVER more about your products through ni.com. Power Supplies Support Services NI Community Solutions ni.com/support ni.com/services ni.com/community ni.com/powersupplies *This item is also installed with the driver software. NI PXIe-414x Getting Started Guide | © National Instruments | 9... -
Page 10: Worldwide Support And Services
Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at .
Need help?
Do you have a question about the NI PXIe-4140 and is the answer not in the manual?
Questions and answers