Table of Contents
Advertisement
Quick Links
INSTALLATION and OPERATION MANUAL
Submersible Dewatering Pumps
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Series: SED
.50HP, 1750RPM
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 105240DW-Rev. A
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Crane Barnes SED Series
Summary of Contents for Crane Barnes SED Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notifi cation.
-
Page 2: Table Of Contents
SEAL TOOL KIT ( see parts list) PRESSURE GAUGE KIT (see parts list) Other brand and product names are trademarks or registered trademarks of their respective holders. ® BARNES is a registered trademark of Crane Pumps & Systems, Inc 1984, 2002, 4/06, 8/06 Alteration Rights Reserved... -
Page 3: Safety First
WARNING! - DO NOT pump hazardous materials (fl ammable, caustic, etc.) unless the pump is specifi cally IMPORTANT! - Crane Pumps & Systems, Inc. is not designed and designated to handle them. responsible for losses, injury, or death resulting from a failure to observe these safety precautions, misuse or abuse of pumps or equipment. -
Page 4: Pump Specifications
SECTION: A - PUMP SPECIFICATIONS - Series SED DISCHARGE ....... 2” NPT, Female, Vertical SPEED ......... 1750 RPM (Nominal) LIQUID TEMPERATURE ..104°F (40°C) UPPER BEARING: VOLUTE ......Cast Iron ASTM A-48, Class 30 Design .... Single Row, Ball, Oil Lubricated MOTOR HOUSING .... -
Page 5: General Information
B-4) Service Centers: performance. For the location of the nearest Barnes Service Center, check your Barnes representative or Crane Pumps & Systems, Inc. C-2) Discharge: Service Department in Piqua, Ohio, telephone (937) 778-8947 When any hose is used for connection, keep the hose as or Crane Pumps &... -
Page 6: Electrical Data
NOTE! - The white wire if NOT a neutral TEMPERATURE SENSOR ELECTRICAL RATINGS or ground lead but a power carring conductor. Volts Continuous Inrush Amperes Amperes C-3.2) Overload Protection: 110-120 3.00 30.0 C-3.2-1) Three Phase (optional) - The normally closed (N/C) thermal sensor is embedded in the motor windings and will 220-240 1.50... -
Page 7: Preventative Maintenance
D-2.2) Incorrect Rotation for Single-Phase Pumps: clean, clear, light amber in color and free from suspended In the unlikely event that the rotation is incorrect for a single particles. Milky white oil indicates the presence of water. phase pump, contact a Barnes Service Center. Oil level should be above motor when pump is in vertical position. - Page 8 To install impeller (33), clean the threads with thread locking compound cleaner. Apply removable Loctite® 603 or equivalent to shaft threads. Screw impeller onto the shaft hand tight while using a screwdriver in the slot at the end of the shaft to hold it stationary. Apply thread locking compound (60) to shaft threads.
- Page 9 Motor & Seal Plate Seal Pusher Rotating Member Bullet (28B) FIGURE 7 F-4.1) Disassembly and Inspection: To examine or replace the motor (7), capacitor (9, single phase units), controls (55, 56, optional), and bearing (16), drain oil FIGURE 5 from motor as outlined in paragraph F-1.1. Disassemble volute IMPORTANT! - DO NOT hammer on the seal and impeller as outlined in paragraph F-2.1 and disassemble pusher- it will damage the seal face.
- Page 10 Check power cables (16), for cracks or damage and replace if required. Make internal wiring connections which are independent of the terminal block as shown, using connectors (48) and wire assemblies (49) and (63) as required. Do not use wire nuts. Slip motor leads and ground wire through fi berglass sleeve.
-
Page 11: Replacement Parts
SECTION: G REPLACEMENT PARTS G-2 PART NUMBER: The part number consists of a six (6) digit number, which G-1 ORDERING REPLACEMENT PARTS: appears in the catalog. A one or two letter suffi x may follow this When ordering replacement parts, ALWAYS furnish the number to designate the design confi... -
Page 12: Wire Schematics
FIGURE 12... -
Page 13: Trouble Shooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 14: Exploded View, (Fig. 14)
Series: SED FIGURE 13... -
Page 15: Parts List
PARTS KITS Seal Repair Kit...P/N - 130180 (ª) 3, 18, 20, 28, 36 Seal Tool Kit....T/L - 107271 Pressure Gauge Kit...P/N-085343 PARTS LIST ITEM PART NO. DESCRIPTION 105196 Housing, Motor Cast Iron 105196HA Housing, Motor Cast Iron 071114 Body, Tapped 070713SD ª... - Page 16 TABLE 2 - POWER CORD SETS ITEMS #16 ITEM #16 ITEM #16 CABLE LENGTH 240 VOLT, 1 PHASE 120 VOLT, 1 PHASE 3 PHASE 0.5HP 8 FT. 103756A --------- 103742A 15 FT. 103756 110949 103742 20 FT. 103756XA 110949XA 103742XA 30 FT.
-
Page 17: Warranty
Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state. -
Page 18: Warranty Registration
Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
Need help?
Do you have a question about the Barnes SED Series and is the answer not in the manual?
Questions and answers