Samsung LH008IWJMWR Installation Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. LH008IWJMWR
  6. Installation manual

Samsung LH008IWJMWR Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Samsung Electronics
LED Display
Installation Manual
LH008IWJMWR (P0.84)
LH012IWJMWR (P1.26)
LH016IWJMWR (P1.68)
SNOW-1810U (S-Box)
J2014003 (Power Shelf)
CP3500 (Power Rectifier)
Ver. 0.3
(2020. 08. 04)

Advertisement

Table of Contents
loading

Related Manuals for Samsung LH008IWJMWR

Summary of Contents for Samsung LH008IWJMWR

  • Page 1 Samsung Electronics LED Display Installation Manual LH008IWJMWR (P0.84) LH012IWJMWR (P1.26) LH016IWJMWR (P1.68) SNOW-1810U (S-Box) J2014003 (Power Shelf) CP3500 (Power Rectifier) Ver. 0.3 (2020. 08. 04)
  • Page 2 Installation Manual History Note Samsung Electronics Version Date Last Edited by Detail 2020. 06. 26 Daehwan Sohn - Initial Release 2020. 07. 09 Daehwan Sohn - Global Tech Sales Group, B2B Field Quality Group requirements added 2020. 08. 04 Daehwan Sohn...
  • Page 3 Check first before installation (1/3) Samsung Electronics • All power cables and OCM cables must be connected firmly. • For HDBT signal stability, use the cable above CAT6 *STP, *FTP level. (Length 15m~100m) “CAT6 UTP cannot be allowed” - Do not use “comb” or “pinstripe” cable.
  • Page 4 Check first before installation (2/3) Samsung Electronics • Install the device only using SNOW-1810U and its supplied IG. ※ Please check below Cabinet and S-Box compatibility table information. S-Box SNOW-1810U SNOW-1703ULD SNOW-1703U BN91-20525A BN91-19993A BN91-19100A Cabinet IF015H, IF015H, IF015H, IF020H,...
  • Page 5 Check first before installation (3/3) Samsung Electronics • This manual is for LH008IWJMWR / LH012IWJMWR / LH016IWJMWR by Samsung Electronics. Only essential contents are included for Power Shelf / Power Rectifier by GE. Use the link below to see all the instructions for products by GE before installation.

  • Page 6: Table Of Contents

    Table of Contents Samsung Electronics ( 6 page ) Product Information and Precautions for Installation Check Point about the Radiant Heat ( 17 page ) ( 23 page ) Preparation for Cabinet Installation ( 30 page ) Frame Installation ( 38 page )

  • Page 7: Product Information And Precautions For Installation

    1. Product Information and Precautions for Installation Samsung Electronics ◇ Cabinet Product Information IW008J (P0.84) IW012J (P1.26) IW016J (P1.68) 0.84 mm 1.26 mm 1.68 mm Pitch Basic Spec Cabinet Resolution 960 X 540 640 X 360 480 X 270 1000-nit / 500-nit...
  • Page 8 1. Product Information and Precautions for Installation Samsung Electronics ◇ Screen Configuration by LED Pitch (Please refer page 22 for Frame Kit Configuration in detail.) Spec P0.84 P1.26 P1.68 Cabinet Size 806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.8...
  • Page 9 1. Product Information and Precautions for Installation Samsung Electronics Essential : Selective by ◇ Off-Power Board VPS Unit Configuration installation condition Essential VPS 1 (VG-RPWSKIT, Power Shelf Set) Index Product Name Vendor Part Number Index Product Name Vendor Part Number...
  • Page 10 1. Product Information and Precautions for Installation Samsung Electronics ◇ Off-Power Board VPS Unit Configuration - Detail VPS 1 (VG-RPWSKIT, Power Shelf Set) 3. AC Cable Index Product Name Vendor Part Number Power Shelf ABB (GE) J2014003L001A Power Rectifier ABB (GE)
  • Page 11 1. Product Information and Precautions for Installation Samsung Electronics ◇ Off-Power Board VPS Unit Configuration - Detail Index Product Name Vendor Part Number AWG 12, 2C, 300V, UL2464 100m JWHARNESS004 Daisy Power Cable 1.5m JWHARNESS001 MCB (Miniature Circuit Breaker) ABB (GE) S201-C25 1.
  • Page 12 1. Product Information and Precautions for Installation Samsung Electronics ◇ Off-Power Board VPS Unit Configuration - Detail VPS 5 Index Product Name Vendor Part Number 1. MCB Rack Mount Frame MCB Rack Mount Frame PEN ELECOM R1299/3UK-KIT Index Product Name...
  • Page 13 1. Product Information and Precautions for Installation Samsung Electronics ◇ The Wall Pro UHD Screen and Power Shelf Installation Guide by Installation Condition Power Shelf Power Shelf Power Shelf Cabinets Cabinets for Cable Qty Model Cable Length Qty Needed Qty Needed...
  • Page 14 1. Product Information and Precautions for Installation Samsung Electronics  Example for VPS purchase according to installation condition Example 1) Screen : UHD X 3, Model : P1.26, Distance : 80m, Supply Voltage : 220V → Cabinet 108(=36 * 3)EA, Shelf 5EA Needed, Cable Length and Quantity : 100m / 54 EA...
  • Page 15 1. Product Information and Precautions for Installation Samsung Electronics ◇ Precautions for Installation (LED damage) Caution Image [ Beware of Outside Impact, Fall] ① Beware not to cause any impact on the LED screen or drop the product on the floor MODULE after the protection gets taken off for installation.
  • Page 16 1. Product Information and Precautions for Installation Samsung Electronics ◇ Caution for cleaning screen ★Caution★ - Watch out for damage when cleaning gap between Half-Cabinets. - Watch out for damage when cleaning gap between Modules. - Do not insert any cleaning tool or spay cleaner directly into the gap.
  • Page 17 1. Product Information and Precautions for Installation Samsung Electronics ◇ 설치 준비 • Provided in Accessory Kit (CY-WJJPWP). ※ 권장 규격 (-) (+) driver PROTECTION EDGE PROTECTION V/H MAGNET JIG GAP TOOL (BN81-17114A) (BN81-17111A) (BN81-17514A/BN81-17515A) (BN81-17113A) • Provided as Cabinet Accessory...

  • Page 18: Check Point About The Radiant Heat

    ※ Written under ‘Full white, (back light 7)’ standard Written under ‘Video, (back light 10)’ standard Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA) ※ ADA(American’s with Disabilities Act Ceiling installation, outdoor installation, cannot be installed where there is vibration It is not possible to install it in a special case, and it is necessary to consult technical sales separately.
  • Page 19 2. Check Point about the Radiant Heat– without Fan Samsung Electronics ※ At least 60mm installation space required for upper,  Minimum spacing for buried installation lower, left, and right All interior finishes proceed after screen installation Recommended condition : Min 500mm (set ~ ceiling)
  • Page 20 2. Check Point about the Radiant Heat– without Fan Samsung Electronics  Minimum spacing for buried installation Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation...
  • Page 21 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement during landfill installation Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to...
  • Page 22 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement when installing walls Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to...
  • Page 23 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement during rear exhaust Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation The SCREEN wall is managed below 30 ℃...
  • Page 24 3. Preparation for Cabinet Installation Samsung Electronics ◇ Preparations Before Installation ① Remove the Box tape at the upper area and then open up the box. (Fig.2) ② Remove the Top–Cushion and cut out Vacuum bag, and pull out the set.
  • Page 25 3. Preparation for Cabinet Installation Samsung Electronics ④ 18ea Holder-PCB fixing screws and 4 Cover-PCB fixing screws are released. ⑤ Remove the filament tape attached to the top / bottom / left / right. Fig.4 Holder-PCB & Cover-PCB & Protective Sheet Removal...
  • Page 26 3. Preparation for Cabinet Installation Samsung Electronics ⑥ Unfasten the 4 screws on the Cover Corner area (Fig.4) SCREW SCREW-MACHINE (6003-000133, M4,L8) Fig.4 Cover Corner Removal...
  • Page 27 3. Preparation for Cabinet Installation Samsung Electronics - Using Spacer-PET ⑦ When Black Seam occurs, remove the Spacer-PET of the point. ※ Spacer-PET should not be protruded more than module ⑧ If necessary, attach Spacer-PET. (Fig.5) ※ Check the gap between the module and the Bracket-Sub using a gap gauge.
  • Page 28 3. Preparation for Cabinet Installation Samsung Electronics ◈ Dehumidification ① In order to protect the LED device, dehumidification is required if the following conditions apply. [ Dehumidification while installing ] - When installed in a vacuum-packed state after factory shipment for more than 6 months - When installing after storing for more than one week in a non-vacuum packaging.

  • Page 29: Preparation For Cabinet Installation

    3. Preparation for Cabinet Installation Samsung Electronics ◈ Process of Dehumidification - Dehumidification process goes on automatically for 24 hours as the brightness increases gradually. Step condition Brightness Time Lighting up display with 10 gray scale 2 hr Lighting up display with 20 gray scale...
  • Page 30 3. Preparation for Cabinet Installation Samsung Electronics ◈ Reference : Process of Screen Check TOGGLE SWITCH SWITCH POWER INLET POWER OUTLET 화면 검사 사진 확인 Check the picture of the screen ◈ Internal White Pattern 1. After turning power on, press the toggle switch button for 5 seconds.

  • Page 31: Frame Installation

    4. Frame Installation Samsung Electronics ◇ Frame Kit Composition ⓑ ⓒ ⓑ ⓐ VG-LFJ08SWW VG-LFJ08FWW VG-LFJ08TWW VG-LFJ08UWW Item Units Units Units Units ⓐ BRACKET H (horizontal) ⓑ BRACKET SIDE (vertical) ⓒ BRACKET MIDDLE (vertical) ⓓ JOINT H ⓔ JOINT V ⓓ...
  • Page 32 4. Frame Installation Samsung Electronics ① Assemble Bracket Side/Middle with Bracket H. - First insert ⓐBracket H to assembled Joint H and Bracket H. (Fig.1) - Second put 3 groups of Bracket H on ground. And insert Bracket Side/Middle to Bracket H. (Fig.2) .
  • Page 33 4. Frame Installation Samsung Electronics ② Assemble Leveler on the Bracket Side at required height position. - Put Leveler on Bracket side at required height position with moving up and down. (Fig.1) M4L8 Screw Fig.1 Assemble Leveler...
  • Page 34 4. Frame Installation Samsung Electronics ③ Install assembled Frame on the wall. - Place the assembled frame on the wall, align it with the desired height and level, and fasten one place at the top center. (Fig.1) - When attaching the frame to the wall, use the 6mm hexagonal wrench to correct the gap with the leveling bolt. (Fig.2 If the leveling bolt is not enough to attach to the wall, add Tape Wash to reinforce it.
  • Page 35 4. Frame Installation Samsung Electronics - When the leveling work is completed, additional frame and wall should be fastened according to the guide below. (Fig.3) - Fix the fastening position closest to the bracket side / lid among the fastening holes of the bracket H.
  • Page 36 4. Frame Installation Samsung Electronics ※ Precautions for fastening the screws...
  • Page 37 4. Frame Installation Samsung Electronics ※ Frame Extensions for Horizontal / Vertical direction. - Assemble Joint C (Horizontal) / Joint V (Vertical) into second assembled frame. M4L8 Fastening M4L8 Fastening <Horizontal Extension> <Vertical Extension> - Insert the second FRAME to first FRAME.
  • Page 38 4. Frame Installation Samsung Electronics ※ Frame Extensions for Horizontal / Vertical direction. - Mount the Jig by connecting first frame to second frame. And fasten screws. M4L8 Fastening <Horizontal Extension> M4L8 Fastening <Vertical Extension>...

  • Page 39: Cabinet + Frame Installation

    5. Cabinet + Frame Installation Samsung Electronics ◇ Fix I/G position Install I/G first on the back side of the Cabinet (Fig.1) ※ Locate the I/G at the point 50~55mm below from the carving at the right side of the frame, and fasten the screw to fix. (Fig.2) ※...
  • Page 40 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ① After installing frame I/G, install cabinets from the bottom line. (Fig.1) ※ Cabinet should be installed from bottom to top, from left to right. ② Adjust the corners of the cabinet to each carvings to be closer to the frames. (Fig.2) ③...
  • Page 41 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ④ After installing I/G, install Cabinets starting from one end of 1 floor. (Fig.3-1) ※ Tighten the cabinet installed using align jig, and then fasten the screws. (Fig.3-2) M4 L8 Fastening Fig.3-1 Cabinet Installation...
  • Page 42 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ⑤ Install the 1 floor cabinets using align jig. (Fig.4) ⑥ Install other upper floors with the same way. (Fig.5, 6) ※ Check the status of switch of the rear cabinet as “STB Mode” after installing each floor.
  • Page 43 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation 1. When install more than 2 cabinets, follow the instructions below to protect modules - Push and slide the modules (①,②) with the opposite direction of cabinet to be installed.
  • Page 44 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation 2. When install more than 2 cabinets, follow the instructions below to protect modules - Push and slide the modules (①,②) with the opposite direction of cabinet to be installed.
  • Page 45 5. Cabinet + Frame Installation Samsung Electronics ◇ Z-axis gap leveling by Half-Cabinet - Each Half-Cabinet has eight height controls. (4 corners / 4 sides) - Two Half-Cabinet Z-Step adjustments are as follows ① Check the corner of the Half-Cabinet to check if there is a difference.
  • Page 46 5. Cabinet + Frame Installation Samsung Electronics ◇ Adjust Z-leveling between modules 1. Attach Suction-Pad at four corners 2. Move Module 2.0mm 3. Insert Gap-Tool Turn Gap-Tool 90degree 2.0mm Un-Lock Lock ~2mm 90° 5. Hold Module by Hand Turn Gap-Tool 90degree, Remove Gap-Tool 4.
  • Page 47 5. Cabinet + Frame Installation Samsung Electronics - Assemble the cover PCB at the bottom of the cabinet after the first row cabinet installation. - After assembling the Cover PCB, tighten the braid bolts to align the module pixels. * After installing each unit, make sure that the switch on the back of the cabinet is in the “ STB ” mode Cover PCB Fig.1 Fastening screw from Cover PCB to adjust pixel alignment...
  • Page 48 5. Cabinet + Frame Installation Samsung Electronics ◇ Aligning modules in X-, Y-axis directions - Adjust the alignment of modules by attaching Cover PCB on the edge of the screen. ※ X-, Y-axis direction module alignments should be done after Z-axis gap leveling.
  • Page 49 5. Cabinet + Frame Installation Samsung Electronics ◇ Aligning modules in X-, Y-axis directions - After installing the Cover PCB on each edge, install the Holder PCB. ※ The Holder PCB is a device to prevent from being made gaps between modules.
  • Page 50 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Power Shelf / Power Rectifier - Model Name : J2014003 (Power Shelf) / CP3500 (Power Rectifier) by GE - 4 Power Rectifier mountable per 1 Power Shelf Power Shelf Power Rectifier...
  • Page 51 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Power Shelf / Power Rectifier Assembly - Power Rectifier - CP3500 ▶ Input : 100-120 / 220-277 Vac ▶ Default Output : ±54 Vdc @ 1500W / 3500W; 5 Vdc @ 10W * Power Rectifier →...
  • Page 52 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Power Cable / Power Daisy Chain Cable / DC Inlet - Power Cable AWG 12, 2C, 300V, UL1277, 35m / 65m / 100m ※ Lugs that can make Power cable connectable to the Power Shelf should be attached on the end of the Power Cable manually before all the installation process.
  • Page 53 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  AC Power to Screen Flow Chart AC Power AC 110V / 220V POS1 POS3 POS4 POS2 Power Rectifier & DC 48V 6 Cable Outputs Power Shelf (Common) per 1 Output Port...
  • Page 54 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Power Shelf / Power Rectifier Assembly / Disassembly ① Push the buckle to open ② Push the power rectifier fully ③ Power rectifier can be assembled the white cover of front Power...
  • Page 55 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Install MCB(Miniature Circuit Breaker) on the Cable ※ MCB should be applied to all the DC cables to be installed. ② Cut off enough length of ① Peel off enough length of the the one of two cables and ③...
  • Page 56 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  MCB (Miniature Circuit Breaker) Mounting and Frame install ① Hang the upper rear side of ② Push up the lower black ③ If needed to detach MCB from the MCB on the mount rack frame...
  • Page 57 6. Power Shelf Installation and Cabinet Connection Samsung Electronics ※ All the sequence should be done  Attach Lug on the DC Cables under the Power shelf and Cables being disconnected from AC Power. ① Peel off the covering of DC ②...
  • Page 58 6. Power Shelf Installation and Cabinet Connection Samsung Electronics ※ All the sequence should be done  Connect Power Shelf and Cabinets under the Power shelf and Cables being disconnected from AC Power. ① Insert same colored 6 AWG12 ② Open the output connector cover ③...
  • Page 59 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Precautions for Power Shelf / Power Rectifier – DC Output connection - Routing of the DC output cables should guarantee that cables are not in contact with sources of heat and surfaces that may damage the cable insulation.
  • Page 60 6. Power Shelf Installation and Cabinet Connection Samsung Electronics ※ All the sequence should be done  Installation of Power Shelf on the Rack under the Power shelf and Cables being disconnected from AC Power. ① Power Shelf is high voltage product. Be sure to let it be installed inside the rack or installation structures.
  • Page 61 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Connection of AC Power input on the Power Shelf - The AC Cable provided from VPS 1 is open-type cable without AC Cord Connector. To connect AC power, it is necessary of using AC Cord and cable compatible and certified for the installed region or country.
  • Page 62 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Precautions for Power Shelf / Power Rectifier – Mounting and Installation - An accessible AC disconnect/protection device to remove AC power from the equipment in the event of an emergency must be provided.
  • Page 63 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Monitoring Tool Installation and Connection - Using Monitoring Tool Kit included VPS7(VG-RPWAMIB), Power Shelf and Rectifier can be made connected and monitored via PC. - Cover for Shelf Interface Board should be assembled using its screws from 4 edges before connection and operation.
  • Page 64 6. Power Shelf Installation and Cabinet Connection Samsung Electronics ※ The processes below are also applied to  Connect Cables on the Cabinet properly Power Daisy Chain Cable equally. ※ It is recommend that the Power Cable and Power Daisy Chain Cable is to be connected to the cabinet vertically.
  • Page 65 6. Power Shelf Installation and Cabinet Connection Samsung Electronics ※ It is recommend that the Power Cable and  Cabinet Power Daisy Chain Connection Power Daisy Chain Cable is to be connected to the cabinet vertically. ① Connect the Power Daisy Chain Cable ②...
  • Page 66 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Precautions for Power Shelf / Power Rectifier – Mounting and Installation - This product must be installed, serviced, and operated only by skilled and qualified personnel who have the necessary knowledge and practical experience with electrical equipment and who understand the hazards that can arise when working on this type of equipment.
  • Page 67 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Precautions for Power Shelf / Power Rectifier Safety Symbols and Guidelines - Read and understand all instructions before attempting any installation of this product. When installing, operating, or maintaining the J85480S1 Power System, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons.
  • Page 68 6. Power Shelf Installation and Cabinet Connection Samsung Electronics  Power Shelf, MCB Mount Frame, S-Box installed feature Power Shelf & Power Rectifier MCB Mount Frame S-Box ※ Installation location, orders and inner cable connection can be controlled at working person’s...

  • Page 69: Disassembly & Front Service

    7. Disassembly & Front Service Samsung Electronics 0. Disassemble bezel and Cover/Holder PCB Remove Bezel GAP SHEET Cover-PCB Vertical center line Remove Cover PCB and Holder PCB Horizontal center line M3L6 M4L6 Holder-PCB M4L6...
  • Page 70 7. Disassembly & Front Service Samsung Electronics How to use Absorber • Un-Lock Lock ※ Absorber : Handle type tool that fixed on cabinet front side(LED side) to prevent damage to LED Modules while assembly/disassembly, moving half- cabinets. ※ Handle should be locked in vertical.
  • Page 71 7. Disassembly & Front Service Samsung Electronics ★Caution★ Cannot use Magnet JIG of other LED display model. (weak magnetic force) 0. Magnet Jig Use proper Magnet JIG matching with specification. 1. Access carefully on 45° not to damage modules. (Do not contact Jig to module, 1cm apart) ※...
  • Page 72 7. Disassembly & Front Service Samsung Electronics Half-Cabinet Disassembly • ① Based on the Half-Cabinets to be replaced, the Half-cabinets on the left/right and top should be pushed outward. (Edge Protection is needed. Refer to the Next) ※ P0.84 4 X 4 Screen (16 Cabinet / 32 half-cabinet) Repairing Half-Cabinet ②...
  • Page 73 7. Disassembly & Front Service Samsung Electronics Edge Protection • • Edge Protection Push cabinets toward outside to get 2mm gap that located on same vertical line with repairing Half-cabinet ※ Cover PCB should be removed. ※ pushing order is important. Follow the numbers ※...
  • Page 74 7. Disassembly & Front Service Samsung Electronics Edge Protection Attachment • ★Caution★ Be careful not to damage module ③ Insert GAP Tool at middle of Top/Bottom edge of half- cabinet to fix gap. A/S-ASSY GAP TOOL ※ Insert horizontally, turn vertically and fix.
  • Page 75 7. Disassembly & Front Service Samsung Electronics Removing Cable and Disassmble Half-Cabinet • ⑤ Identify location of cables need to be removed. ※ Refer to the TCON board picture. (top : Master / bottom : Slave) ※ Remove the cables close to each other.
  • Page 76 7. Disassembly & Front Service Samsung Electronics Removing cable and disassemble Half-Cabinet – Using PLIER JIG • ■ Using PLIER JIG, remove 26P Power Cable(SMPS, Redundancy) ※ There is a groove that takes locking on the top head. ※ Locking can slip if it does not get to the groove correctly A/S-ASSY PLIER JIG ※...
  • Page 77 7. Disassembly & Front Service Samsung Electronics Changing to new Half-Cabinet • ⑦ Remove Cover corner from Buffer Cabinet laid on the floor and lift up half-cabinet with absorber attached. Remove the Half-Cabinets and insert them between edge protection and connect cables of ⑦.
  • Page 78 7. Disassembly & Front Service Samsung Electronics Remove Cables and T-CON Screw • ① Remove screw to disassemble cover terminal Cover terminal Screw point Remove Cover Terminal first to access to release at the top right screw point of T-con board ※...
  • Page 79 7. Disassembly & Front Service Samsung Electronics Remove Cables and T-CON Screw • ② Remove cables and screws of T-CON Board. ※ FFC Cable ※ Rear side of Disassembled Half-cabinet Lift up the locking and pull out to remove cable.
  • Page 80 7. Disassembly & Front Service Samsung Electronics Remove Cables and T-CON Screw • ③ Remove T-CON Board and replace it. ④ Assembly is reverse sequence of disassembly. ※ The Gap pad is attached to the TCON or Bracket-PCB, so don’t skip when replacing new board.
  • Page 81 7. Disassembly & Front Service Samsung Electronics Module (Half-cabinet Module) Store & Packaging • ① Repairing Half-cabinet should be stored with buffer cabinet. ※ Repairing Half-Cabinet Dissemble Half-Cabinet from existing Buffer Cabinet Change it with Repairing Half-cabinet ※ Repairing Half-Cabinet ※...
  • Page 82 7. Disassembly & Front Service Samsung Electronics Module (Half-cabinet Module) Store & Packaging • ※ Module (Half-Cabinet module) (front/rear) ③ ※ Remove repairing half-cabinet from stored buffer cabinet. ※ Remove repairing half-cabinet from buffer cabinet ④ Package Half-cabinet in The Wall LED Module BOX.
  • Page 83 7. Disassembly & Front Service Samsung Electronics DC-DC Board Discharge • - When touching or removing DC-DC Board, it is necessary of checking two points of discharging whether the board had done discharged using discharging Jig. ※ Before disassembling DC-DC Board, remaining current on the DC-DC Board should be discharged.
  • Page 84 7. Disassembly & Front Service Samsung Electronics DC-DC Board disassembly • ① Remove screws over the insulator on SMPS. (6EA) ② Remove AC INLET Cable connected to SMPS. (Do not remove 26pin Power Cable yet) ★ Caution ★ Do not touch except marked spot.
  • Page 85 7. Disassembly & Front Service Samsung Electronics DC-DC Board disassembly • ③ Hold 26pin Power Cable and bottom of SMPS. ④ Lift up the bottom part and pull down to separate. Be careful of protruding part at top of SMPS shield.

  • Page 86: Cable Connection

    8. Cable Connection Samsung Electronics 8-1 Cable Connection • If using 35m DC Cable, at most 5 cabinets are allowed to connected by power daisy chain. • If using 65m DC Cable, at most 3 cabinets are allowed to connected by power daisy chain.
  • Page 87 8. Cable Connection Samsung Electronics 8-2 The Cautions for Cabinet installation and Cable Connection 1) The set installation order Must be Center to Left/Right direction. → The set installation order and The cable connection order are different. 2) After installing cabinets one line is complete, make sure the connection is OK by connecting OCM/Power cable.
  • Page 88 8. Cable Connection Samsung Electronics 8-3 The Direction for Cabinet Installation 1) Installation of First row cabinet starts at the bottom of Left-end. 2) After installing cabinets one line is complete, make sure the connection is OK by connecting OCM/Power cable. Then, Install next line.
  • Page 89 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW008J : Connect OCM Cable forward direction Case 1: Reverse ID-9 ID-8 ID-7 ID-6 internal Link internal Link ID-3 ID:2 ID-5 ID-4 internal Link internal Link...
  • Page 90 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW008J : Connect OCM Cable forward direction Case 2: Reverse internal Link internal Link ID-7 ID-6 ID-9 ID-8 internal Link internal Link Forward ID-5 ID-4 ID-3...
  • Page 91 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW012J : Connect OCM Cable forward direction Case 1: Reverse internal Link internal Link internal Link ID-19 ID-18 ID-13 ID-12 ID-11 ID-10 internal Link internal Link...
  • Page 92 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW012J : Connect OCM Cable forward direction Case 2: Reverse internal Link internal Link internal Link ID-11 ID-10 ID-13 ID-12 ID-19 ID-18 internal Link internal Link...
  • Page 93 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW016J : Connect OCM Cable forward direction Case 1: ID-29 ID-28 ID-27 ID-26 ID-17 ID-16 ID-15 ID-14 internal Link internal Link internal Link internal Link ID-31...
  • Page 94 8. Cable Connection Samsung Electronics 8-4 Cable Connection : by Data Flow [FHD] ◎ IW016J : Connect OCM Cable forward direction Case 2: ID-15 ID-14 ID-17 ID-16 ID-27 ID-26 ID-29 ID-28 internal Link internal Link internal Link internal Link ID-13...
  • Page 95 8. Cable Connection Samsung Electronics 8-5 Cable Connection : by OCM cable installation ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. 2x2 Cabinet Installed (FHD IW008J) DATA OUT DATA IN DATA OUT DATA IN DATA OUT...
  • Page 96 8. Cable Connection Samsung Electronics 8-5 Cable Connection : by OCM cable installation ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. 3x3 Cabinet Installed (FHD IW012J) DATA OUT DATA OUT DATA OUT DATA IN DATA IN...
  • Page 97 8. Cable Connection Samsung Electronics 8-5 Cable Connection : by OCM cable installation ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. 4x4 Cabinet Installed (FHD IW016J) DATA OUT DATA IN DATA OUT DATA IN DATA OUT...

  • Page 98: S-Box Installation And Connection

    9. S-Box Installation and Connection Samsung Electronics • S-Box Installation Precautions ① The S-Box is recommended to be installed in a standard 19-inch server rack. ※ When connecting two or more sets for Multi-link HDR, install them in the six-sided shield rack (Only SBB-SNOWJMU) ②...
  • Page 99 9. S-Box Installation and Connection Samsung Electronics • S-Box Connection ① Input the video signal to the S-BOX. (Input terminal : HDMI, DP) ② Check the signal input from SOURCE STATUS.(RED : HDMI1 , GREEN : HDMI2, Blue : DISPLAY PORT) ③...
  • Page 100 9. S-Box Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable ★ Orderly Rolled (Recommend) Random Rolled ★ (Not Recommend)  Do not use “comb” or “pinstripe” cable.  Use HDBase-T cables with 15 meter long at minimum and 100 meter long at maximum.
  • Page 101 9. S-Box Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable  EMI sources: Keep the cable away from electromagnetic interference environments such as high-voltage electrical cables, electric motors (such as elevators or refrigerators), fluorescent, light-fixtures and so on ...
  • Page 102 9. S-Box Installation and Connection Samsung Electronics ⑨ Instruction for trimming HDBase-T cable on site  STP RJ45 shielded Plug. RJ45 Connector should be CAT6 or CAT7 shielded RJ45 and load bar. Load bar  Insert conductors into the plastic loader : Using the standard wiring scheme shown here (T-568B), insert the conductors into the plastic loader piece of the R-J45 connector.
  • Page 103 9. S-Box Installation and Connection Samsung Electronics ⑨ Instruction for trimming HDBase-T cable on site  Slide the plastic loader down the cable : Slide the plastic loader down the cable as close to the base as possible.  Cut all conductors using the wire cutters, cut all conductors leaving approximately 0.5” remaining.
  • Page 104 9. S-Box Installation and Connection Samsung Electronics ⑨ Instruction for trimming HDBase-T cable on site  Flip the drain wire up onto the RJ-45 connector Flip the drain wire up onto the RJ-45 connector. Clamp the strain relief down on the purple jacket of the BC-HDKat6a cable using the pair of pliers.
  • Page 105 9. S-Box Installation and Connection Samsung Electronics • S-BOX Connection (Redundancy) ① If redundancy connections required, connect from DATA IN port of I/G to DATA OUT port of the last cabinet by OCM Cable. SNOW-1801U • For HDBT signal stability, use the cable above CAT6 *STP, *FTP level.
  • Page 106 9. S-Box Installation and Connection Samsung Electronics • S-BOX Connection (External IR Receiver) ※ Only one external IR receiver is provided for a set. - External IR receiver can be connected to S-Box body or I/G. ※ If the external IR receiver is connected to I/G, ‘Network Standby – On’ should be preset from the S-Box menu.
  • Page 107 • S-BOX Connection (Panel Configuration) ② S-Box Picture Setting according to model • The default picture configurations are optimized for LH015IFH in Samsung factory. • The picture configurations will be configured automatically when you finish the installation. • For the best picture quality, Please connect S-Box and LED displays via LSM software properly.
  • Page 108 9. S-Box Installation and Connection Samsung Electronics • S-BOX Connection (Grouping) - Home → Video Wall : OFF → ON [Cautions!!] Setup supported resolution for grouping before the grouping function of multi s-box is run by LSM. It can cause the noise of picture or blackout, if resolution is not supported.
  • Page 109 9. S-Box Installation and Connection Samsung Electronics ③ Setup the resolution of input PC  PC : Click the right button of mouse → Click Screen resolution → Click Advanced settings  Click “Monitor” tap → Monitor Settings → Setup “Screen refresh rate” to 60Hz...
  • Page 110 9. S-Box Installation and Connection Samsung Electronics ④ Supported resolutions for S-box Grouping (1/2)
  • Page 111 9. S-Box Installation and Connection Samsung Electronics ④ Supported resolutions for S-box Grouping (2/2)
  • Page 112 9. S-Box Installation and Connection Samsung Electronics ⑤ Picture Menu Settings  Such as “Dynamic Contrast”, “Black Tone” and “Auto Motion plus” should be off when using S-Box Grouping, since it may causes a color difference between S-Box.  Menu→ Picture → Advanced Settings, - Dynamic Contrast : default “Medium”...
  • Page 113 9. S-Box Installation and Connection Samsung Electronics • S-BOX Connection (Service port) ① The service port is dedicated port for monitoring to check the usage of OSD and the source being played at the initial installation of the S-BOX. ② Service port has FHD (1920*1080 @60Hz) resolution.
  • Page 114 9. S-Box Installation and Connection Samsung Electronics • Turn on Simple wall mode  Simple wall mode is a wall paper function for end customer who don’t want to leave the Wall is black screen while in off status.  If the Wall screen resolution is covered in a S-box, turn on Simple wall mode in Factory mode.

  • Page 115: Lsm Settings And How To Use

    • - Samsung Display Solutions (https://displaysolutions.samsung.com) # Download Permission Needed # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > LED Signage Manager - SLM (https://www.secslm.com) # Download Permission Needed # SLM > Help > Download Center > "LED Signage Manager" or "LSM"...
  • Page 116 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs Network IP Setting Tool Execute : [Start] – Program – Samsung – LED Signage Manager – Network Configuration Connect PC and Sbox with RS232C Cable, select connected SerialPort(COM*). And click “open” button.
  • Page 117 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Software that adjusts the LED Cabinet Layout in Remote • S-box Ethernet PC and S-box should be connected through Ethernet connection. HDBT Control PC...
  • Page 118 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Start– Login Page • If the LSM gets operated for the first time, the page to set the password will appear. To set the password, users have to input the same password two times and then click the “Start”...
  • Page 119 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) New Connection • To add connection information, you can either use Search function or input the IP address by yourself. If you click on the Search button, the IP addresses available on S-BOX in the same network will appear.
  • Page 120 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs [★ Cautions!] Recommend to use static IP address for the LED devices. If DHCP is used, IP address is changed automatically and LSM can be disconnected.
  • Page 121 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) [★ Cautions!] The network port 1515 and 48485 are used for internal communication between S-BOX and LED Cabinet. It should be include the firewall or network exception if customer used secured network.
  • Page 122 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window-Home Window • Input source: Input source, resolution, connection time of S-BOX are shown. Cabinet Layout : Layout, number of units, number of connections and number of disconnections in all LED cabinets are shown.
  • Page 123 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window-Edit Connection Layout Window • Connection layout: The location and the layout of each LED cabinet are adjusted in the output source area of the S-BOX.
  • Page 124 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window-Connection Window • Device connection list view: Check S-BOX composition, modify and delete S-BOX connection, show by each LED Cabinet Group Connection layout (View Port):...
  • Page 125 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window-Connection Window - Device Information/Setting View • 1. Basic : . Power On/Off, Change input source, Screen Mute / Freeze, Menu Size 2.
  • Page 126 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window – Connections Window – Device Information / Settings View • 3. LED Cabinet Calibration . Cabinet Calibration └ Cabinet RGB CC : Control RGB CC Matrix by Cabinet unit.
  • Page 127 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window – Connections Window – Sub Information View • Monitor Window: Checking MDC communication log and connected device information available, able to be extracted via file...
  • Page 128 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Main Window - Preferences • Options number of times the command retried interval of checking error status alarm temperature warnings Support program language...
  • Page 129 10. LSM Settings and How to Use Samsung Electronics 10-1. Control Program for PCs LSM(LED Signage Manager) Dehumidification mode using LSM • Dehumidification button is located in S-Box menu. When you click the button, dehumidification starts. You can see how long it takes.

  • Page 130: Precaution For Lsm Connection

    11. Precautions for LSM Connection Samsung Electronics ■ S-Box Network Connection via LSM ① When LSM cannot find S-Box or shows disconnected message - Check Ethernet Cable Connection. - Check IP settings of S-Box. - Check the target IP of S-Box in LSM.

  • Page 131: Color Calibration

    12. Color Calibration Samsung Electronics ■ On-Site Calibration - Calibration function provided via measurement device (Colorimeter) and mobile devices. - Module calibrations can be automated by S/W. - Module / Half Cabinet / Cabinet / Screen Calibration function provided. - Can be used as Install / Maintenance purpose...
  • Page 132 (displaysolutions.samsung.com) # Download Permission Needed # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > Color Expert LED - Measured Value or User input can be used as a reference value. - PC Colorimeter Calibration Manual...
  • Page 133 Samsung Display Solution (displaysolutions.samsung.com) # Download Permission Needed # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > Color Expert LED - Choose calibration unit. (Module or Cabinet) - Specify Reference and Target. - Set viewing location using red guidelines and launch White Balance Correction.

  • Page 134: Bezel Installation

    13. Bezel Installation Samsung Electronics ◇ Bezel Installation 1. Attach ASSY FRAME-BEZEL SIDE to the cabinets. • Check the allowable gaps for each FRAME-BEZEL SIDE. • If the gaps need to be adjusted, put the Gap sheet on the magnet side.
  • Page 135 13. Bezel Installation Samsung Electronics ◇ Bezel Installation 2. Use M3L5 screw to mount the BRACKET LINK to the right side of the FRAME BEZEL TOP BOTTOM. M3,L5 BRACKET CENTER...
  • Page 136 13. Bezel Installation Samsung Electronics ◇ Bezel Installation 3. Place the ASSY FRAME-BEZEL TOP BOTTOM to the top left of the cabinet. • Align the FRAME-BEZEL SIDE and FRAME-BEZEL TOP BOTTOM to ensure there is no gap between them. • Use 2 M3L5 screws to mount the left side of the FRAME BEZEL TOP BOTTOM to the FRAME BEZEL SIDE.
  • Page 137 13. Bezel Installation Samsung Electronics ◇ Bezel Installation 4. Place the FRAME-BEZEL TOP BOTTOM to the top right of the cabinet. • Align the FRAME-BEZEL SIDE and FRAME-BEZEL TOP BOTTOM to ensure there is no gap between them. • Use 2 M3L5 screws to mount the right side of the FRAME BEZEL TOP BOTTOM to the FRAME BEZEL SIDE.
  • Page 138 13. Bezel Installation Samsung Electronics ◇ Bezel Installation 5. Use 2 M3L5 screws to mount the left side of the FRAME-BEZEL TOP BOTTOM. [Fig.1] 6. Use 6 M4L8 screws to mount the FRAME BEZEL TOP BOTTOM to the screw holes on the cabinet.
  • Page 139 13. Bezel Installation Samsung Electronics ◇ Bezel Installation 7. Install the bezel on the lower side of cabinet following former 2 process. * Be cautious of gaps not to be made at the point between FRAME BEZEL SIDE and FRAME BEZEL TOP BOTTOM.
  • Page 140 13. Bezel Installation Samsung Electronics ◇ Bezel Extension • Vertical Extension - Connect FRAME-BEZEL LEFT & RIGHT for over 5~8 Cabinets using M3L3 screws. M3,L3...
  • Page 141 13. Bezel Installation Samsung Electronics ◇ Bezel Extension • Horizontal Extension - Follow the basic installation steps of bezel installation in case of horizontal extension. - If you had installed 6 Cabinets horizontally, you need 3 Frame Bezel Top & Bottom.
  • Page 142 14. Reference – Module Attachment Principle Samsung Electronics Section view HOLDER-MAGNET It is possible to adjust height by driver. (4 points per module) => Return in a CCW direction (1mm per 1 rotation) LED MODULE BRACKET-SUB BRACKET MAGNET LED MODULE...
  • Page 143 14. Appendix - How to separate Module Samsung Electronics < Edge protection > Disassemble Cover-PCB Attach Protection Make gap (move module 2mm ) Separate Module with Magnet jig Full Protection Module for change Magnet Magnet in protection Stud in module section 0.5mm gap...
  • Page 144 14. Appendix ※ HDbaseT Certified Cables Samsung Electronics ★ For HDBT signal stability, do not use CAT5E cables even though the cables are included in the following list Vendor Model Name Vendor Model Name HNCPRO(TM) HOME NETWORK CABLE Trends Electronics...
  • Page 145 14. Appendix ※ HDbaseT Certified Cables Samsung Electronics ★ For HDBT signal stability, do not use CAT5E cables even though the cables are included in the following list Vendor Model Name Vendor Model Name Kramer Electronics BC-HDKat6a Snap AV SP-CAT6A-1000-BLU BC-UNIKat CAT.

This manual is also suitable for:

Lh012iwjmwrLh016iwjmwrP0.84P1.26P1.68

Table of Contents