Samsung QP Series Quick Setup Manual

Quick Setup Guide
QP82R-8K
* Recommended hours of use per day of this product is under 16 hours. If the product is
used for longer than 16 hours a day, the warranty may be void.
* The colour and the appearance may differ depending on the product, and the content in
the manual is subject to change without prior notice to improve the performance.
* Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Checking the Components
Contact the vendor where you purchased the product if any components are missing.
The pictures may look different from the actual components.
Warranty card
Quick Setup Guide (Not available in some
locations)
Holder-Ring
Stand / Screw (M4 x L14) x 4
(For Wall Mount) x 4
HOLDER-CABLE Bending Cover
Batteries (AAA x 2)
(Not available in some Remote Control
locations)
One Invisible Connection /
One Connect One Connect Power Cable
Parts
4
1,2
Remote sensor
1
Press a button on the remote control pointing at the bottom of
the product face to perform the function. The remote control
sensor is located on the bottom of the product.
* Using other display devices in the same space as the remote
control of this product can cause the other display devices to be
inadvertently controlled.
Control button
2
ꞏ button: Turns the product on.
- Press button: Display the Control menu. / Select or run a
focused item on the menu.
- Press and hold
ꞏ Up/Down/Left/Right Button: Move the menu.
ꞏ Left/Right Button: Changes the volume.
Control menu
3
ꞏ Home: Enter MagicInfo or URL Launcher mode.
ꞏ Settings: Display the OSD menu.
ꞏ Return: Exit the control menu.
ꞏ Source: Select the connected input source.
ꞏ Power off: Power off the product.
Power indicator
4
BN68-09675B-00
Connecting the product to the One Connect
QP82R-8K
RS232C adapter
QP82R-8K
Screw (M4 x L12)
One Connect
One Connect
Troubleshooting Guide
Issues
The screen keeps
switching on and off.
3
No Signal is
displayed on the
screen.
Speaker
Not Optimum Mode
is displayed.
button: The running function is terminated.
The images on the
screen look distorted.
The screen appears
unstable and shaky.
There are shadows or
ghost images left on
the screen.
One Connect
10 cm
Bending Cover
x 1
(M4 x L12)
One Connect
Solutions
Check that the cable between the product
and the PC is connected correctly.
Check that the product is connected
correctly with a cable.
Check that the source device connected to
the product is powered on.
Depending on the type of external device,
the screen may not display properly. In this
case, connect it with the HDMI Hot Plug
function turned On.
This message is displayed when a
signal from the graphics card exceeds
the product's maximum resolution and
frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
Check the cable connection to the product.
Check that the resolution and frequency of
the PC and graphics card are set within a
range compatible with the product. Then,
change the screen settings if required by
referring to 'Preset Timing Modes' .
Connect the product and One Connect referring to the
image.
1 Following the steps in the image, use One
1-4
Invisible Connection to connect the product and One
Connect.
2 Use the power cable to connect One Connect to a wall
outlet as shown in step 5.
* When arranging the remaining cable, refer to the
figure for the correct arrangement.
CLASS 1 LASER PRODUCT (One Invisible Connection)
ꞏ Caution - Invisible laser radiation when open. Do not
stare into beam.
- Do not bend the One Invisible Connection cable
excessively. Do not cut the cable.
- Do not place heavy objects on the cable.
- Do not disassemble either of the cable connectors.
ꞏ Caution - Use of controls, adjustments, or the
performance of procedures other than those specified
herein may result in hazardous radiation exposure.