Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nauticam NA-G7XIII
Summary of Contents for Nauticam NA-G7XIII
- Page 2 ORWARD Thank you for your purchase of a NAUTICAM housing. At NAUTICAM, we pride ourselves in the ability to recognize the requirements of professional as well as amateur underwater photographers and fulfill them through the innovative designs of our products. We strive to achieve a high level of user-friendliness by allowing stress-free installation and easy operation of all important functions of the camera.
-
Page 3: Table Of Contents
ABLE OF ONTENTS Warranty …………………………………………………………………………………………………………….…… Precautions ……………………………………………………………………………………………………………… Package Contents ……………………………………………………………………………………………….…… Specifications ……………………………………………………………………………………………………..…… Identification of Parts ……………………………………………………………………………………………… Opening and Locking the Housing …………………………………………………………………………… Preparation of the Housing ……………………………………………………………………………………… Installing the Camera ………………………………………………………………………………………….…… Changing the Port …………………………………………………………………………………………………… Connecting HDMI Cable…………………………………………………………………………………………… Care and Maintenance ……………………………………………………………………………………….…… Optional Accessories …………………………………………………………………………………………..……... -
Page 4: Warranty
NAUTICAM does not hold responsibility for damage, of any nature, to any equipment used with and/or placed within our products. NAUTICAM accepts no liability for any loss of captured images or the inability to capture images even if it is due to the malfunctioning of our products. -
Page 5: Precautions
O-ring(s). • Do not use lubricants from other brands with the silicone rubber O-ring on this housing, only use the lubricant provided by NAUTICAM. • Discontinue use immediately should you notice any leakage. - Page 6 • Do not open the product in a wet or sandy environment. Protect the interior from moisture and debris in order to prevent malfunction or leakage. • Do not store the product in an environment of high humidity. • Do not leave the housing and the monitor in direct sunlight for prolonged periods. •...
-
Page 7: Package Contents
ACKAGE ONTENTS • NA-G7XIII Housing • N50 Standard Port with Cap • 2x Handles Brackets • 2x Optical Bulkhead Plugs • Shutter Release Extension • 90135 Spare Silicone Rubber O-ring for Housing • O-ring Remover • CR2032 Battery • Lubricant •... -
Page 8: Specifications
PECIFICATIONS Housing body: Aluminum alloy Construction Surface treatment: Hard anodized Display window: Abrasion resistant polycarbonate Width: 155mm (w/o handles) Dimensions Height: 103mm Depth: 111mm Weight in air Approx. 0.95kg Weight in water -0.05kg Depth rating 100 m Port mount Compatible Canon PowerShot G7X Mark III Camera cameras... -
Page 9: Identification Of Parts
DENTIFICATION OF ARTS Shutter Release Lever Front Control Wheel Optical Fiber Mount N50 Standard Port Port Release Safety Button *Handle brackets and Shutter release extension are not displayed. - Page 10 On/Off Button M14 Accessory Port Exposure Dial Moisture Alarm Window Mode Dial M16 Accessory Port Zoom Lever Zoom Lever Lock Accessory Coldshoe M10 Strobe Mounting Base Port Alignment Index *Handle brackets and Shutter release extension are not displayed.
- Page 11 Threaded Holes for Handle Brackets M16 Accessory Port Housing Lock Safety Button Attachment Point for Hand Strap Flash Up/Off Lever Housing Lock *Handle brackets and Shutter release extension are not displayed.
- Page 12 Mounting Holes for LCD Magnifier Attachment Rails Erase Button Movie Button Control Wheel Up/ Drive Mode Button Left/ MF Button Set/ FUNC. Button Right/ Flash Button Down/ INFO Button Menu Button Playback Button...
-
Page 13: Opening And Locking The Housing
PENING AND OCKING THE OUSING To open the housing: 1. Press the housing lock safety 2. Turn the housing lock anti- button. clockwise for 270°, until the lock reaches the “Open” position as shown. - Page 14 To lock the housing: Turn the housing lock clockwise Close the housing while the for 270°, until the lock reaches housing is in the “Open” position. the “lock” position as shown. Confirm that white indicator line on the safety button is visible.
-
Page 15: Preparation Of The Housing
Prepar REPARATION OF THE OUSING 1. After verifying that the main O-ring is in 4. Setting up the moisture alarm: good condition, lightly coat it with the lubricant provided. 2. Make sure the O-ring groove located in the front part of the housing is free from any foreign material;... - Page 16 Prepar Battery Installation: Press Press Insert the battery as shown above and To remove the battery, press the metal plate as indicated and the battery will then press down the battery. pop out. *Use only recommended battery with this product...
- Page 17 2. Switch the alarm on. The LED light 3. Test the alarm by connecting the two will flash blue once and turn blue wires near the bottom of the housing for five seconds indicating the with a damp cotton bud; the alarm battery is normal.
- Page 18 Optional vacuum valve: Vacuum valve can be attached to the housing via one of the accessory port for conducting a vacuum seal test. Please refer to the manual of the vacuum valve for details of the operation. LED status identification: On start up LED indicator Status...
- Page 19 After start up LED indicator Status Standby mode. The moisture alarm is active, Flashing "Blue" light and the system is ready for vacuum indication whenever a vacuum is detected. Flashing "Red" light Moisture is detected. with beeping sound Some vacuum is detected, target vacuum level Flashing "Yellow"...
-
Page 20: Installing The Camera
NSTALLING THE AMERA To install the camera into to the housing Place the camera inside the housing as shown. Due to space limitation, the pop-up flash needs to be in up position before connecting with the internal HDMI cable. • Flash up lever is disabled when using an external monitor Confirm that all the controls of the housing are correctly engaged. -
Page 21: Changing The Port
HANGING THE Three optional ports are available for different styles of photography. • 38701 N50 Short Port with M67 thread for wet wide-angle lenses (widest focal length only) • 38702 N50 3.5’’ Acrylic Dome Port An acrylic dome port that restore the lens field of view underwater •... - Page 22 To mount Port Align the ‘I’ mark on the port Turn the port clockwise until with the ‘o’ mark on the the ‘o’ mark on the port housing. aligns with the ‘o’ mark on the housing. Gently push the port towards the housing until it cannot go any further.
-
Page 23: Connecting Hdmi Cable
ABLE By adding the optional 25028 Socket Extension and 25032 Custom HDMI bulkhead, the NA-NA-G7XIII is compatible with external monitor housings, such as the NA-502B-H or NA-Ninja V (HDMI 1.4 connection only). The socket extension will be provided for free to use with external monitor housings... -
Page 24: Care And Maintenance
O-ring with the provided lubricant before reinstalling it in the groove. A damaged O-ring should be discarded immediately and replaced only with one that is provided by NAUTICAM. •... -
Page 25: Optional Accessories
PTIONAL CCESSORIES P.N. 25624 P.N. 25123 P.N. 25106 M14 Vacuum Valve II LCD Magnifier attachment rails LCD Magnifier with Dioptric (Pushbutton Release) for NA-S110/S120/TG3/G7X/G7XII/TG5/G7XIII Adjustment P.N. 38022 P.N. 38703 P.N. 38702 Diffuser N50 3.5’’ Acrylic Wide-Angle N50 Short Port with Bayonet for NA-G7X/G7XII/G7XIII housing Mount (To use with WWL-1) Dome Port... - Page 26 P.N. 71206 P.N. 71208 P.N. 71207 Easitray II with left handle Adjustable right handle II Flexitray II with left handle (for Easitray II & Flexitray II) (with 2pcs ¼’’ screws) (with 2pcs ¼’’ screws) P.N. 83201 P.N. 83214 Wet Wide Lens 1 (WWL-1) 130 deg. Bayonet Mount Adaptor for FOV with compatible 28mm Lenses SMC/CMC...
- Page 27 P.N. 81301 P.N. 81302 Compact Macro Convertor 1 Compact Macro Convertor 2 (CMC-1, 4.5X Magnification) (CMC-2, 2.8X Magnification) For external monitors All the needed cables and bulkhead are included in the monitor housing. P.N. 17906/17907 P.N. 17920/17921 NA-502H housing NA-502B-H Housing for Small HD 502 5-inch HD monitor for SmallHD 502 Bright Monitor with HDMI 1.4 input support...
- Page 28 For HDMI Connection, P.N. 25028 P.N. 25032 P.N. 25076 Socket extension Custom HDMI bulkhead to use HDMI (D-D) Cable in 200mm Length for 25032 HDMI bulkhead with M16 thread for NA-XT2/XH1/A6400 with socket extension (for internal connection from HDMI bulkhead to camera)
Need help?
Do you have a question about the NA-G7XIII and is the answer not in the manual?
Questions and answers