Related Manuals for Curtis ILGD-10
Summary of Contents for Curtis ILGD-10
- Page 1 USER GUIDE Digital Interlocking Coffee Grinder READ AND SAVE THESE INSTRUCTIONS NOTICE TO INSTALLER: Please leave this booklet with the machine.
-
Page 2: Table Of Contents
................... IP94 ...................................................ES93 ............................................................................Contact Information Wilbur Curtis Co., Inc. 6913 Acco Street | Montebello, CA 90640 US Phone: 323-837-2300 | Toll Free: 800-421-6150 Email: csrassistance@wilburcurtis.com | Web: www.wilburcurtis.com . - 4:00 . PT Email: techsupport@wilburcurtis.com 101419B... -
Page 3: Fs50
KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS50 Key Features • Easy to Use - Fully automatic operation. • • Highly Accurate and Consistent Throw - For even distribution, dust reduction. • Constant, uniform grind. • Powerful 1/2 hp Motor - Equipped with safety circuit breaker. Coffee Grinder Single 1 PH 120 V... -
Page 4: Is3
INSTRUCTIONS could result in personal injury or void the warranty. • This appliance is designed for commercial use. Any service other than cleaning and preventive maintenance should be performed by an authorized Wilbur Curtis service technician. • serviceable parts inside. - Page 5 IMPORTANT SAFEGUARDS CE Requirements • This appliance must be installed in locations where it can be overseen by trained personnel. • • This appliance is not suitable for outdoor use. • • • This appliance must not be cleaned by water jet. •...
-
Page 6: Ii24
INSTALLATION INSTRUCTIONS II24 WARNING: WARNING: properly grounded. IMPORTANT: Installation Instructions Installation Requirements • A secure surface capable of supporting the weight of the appliance. • For units without an attached cord set: Appropriately sized, UL listed, grounding type power cable to meet enough •... - Page 7 INSTALLATION INSTRUCTIONS II24 Connecting the Power Cord to A Junction Box (units with pre-installed power cord, if applicable) WARNING: the circuit breaker panel before connecting the power cable. Lock out and tag the circuit breaker. ELECTRICAL SCHEMATIC Power cable from grinder Connect the Power Cable On units with a power connector on the back panel, compatible with the electrical outlet installed in the...
-
Page 8: Oi37
OPERATING INSTRUCTIONS OI37 WARNING - TO AVOID SCALDING, AVOID SPLASHING. Keep body parts clear of the brewer during brewing. Do not remove the brew basket while the BREW light is on. Keep body parts away from hot surfaces. The grinder is factory preset for optimal performance. Open one of the hopper Close the lid. -
Page 9: Ci22
CLEANING INSTRUCTIONS CI22 WARNING: Disconnect the power cord before cleaning. WARNING: DO NOT immerse the grinder in water or any other liquid. Avoid spilling liquid into the grind housing during cleaning. NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives. Cleaning the Grinder - As Needed ™... - Page 10 PROGRAMMING GUIDE PG15 Programming Options The grinder has been adjusted at the factory to provide satisfactory performance in most situations. In the event that you would like to vary the grinder settings, it can be reprogrammed. Both sides of the grinder are programmed identically.
- Page 11 ROUGH-IN DRAWINGS RD56 ILGD 14.50 in [36.8 cm] 10.00 in [25.4 cm] 9.88 in [25.1 cm] 21.60 in [54.9 cm] 29.50 in [74.9 cm] 6.55 in 7.44 in [16.6 cm] [18.9 cm] ILGD, ROUGH-IN DRAWING 030118NC...
- Page 12 ILLUSTRATED PARTS/RECOMMENDED PARTS IP94 ILGD - Main Chassis - Exploded View Grinder motor assembly, see section IP96 ILGD, ILLUSTRATED PARTS/RECOMMENDED PARTS 120519D...
-
Page 13: Ip94
ITEM # PART # DESCRIPTION WC-9118 COVER, ASSY DUAL HOPPER GRINDR DHG/ILGD WC-9142 SHAFT, AGITATION WHEEL (OPTIONAL) WC-39212 MEMBRANE CONTRL PANEL CURTIS ILGD WC-9158 AUGER, ASSY DHG,ILG,ILGD WC-13320 HARNESS ASSY, ILGD 120V WC-9183 BEARING, AUGER BRASS DHG,ILG, ILGD WC-13345 HARNESS ASSY, ILGD 220V... - Page 14 ILLUSTRATED PARTS LIST IP96 Grinder Motor Assembly Grinder Motor Assembly - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION WC-37283* KIT, GRINDER CHUTE DHG/ILGD/SH WC-91050 BURR, COMPLETE SET SLICING (NEWER UNITS) MOTOR, SLICING GRINDER ASSY 120V SLG/DHG/ BURR, SET CRUSH HIGH FLOW ILGD /TL-ILGD WC-9135 WC-91045...
-
Page 15: Es93
ELECTRICAL SCHEMATICS ES93 120 Volt Models 220-240 Volt Models ELECTRICAL RATING TABLE Voltage Amps Wa s Hertz # of Conductor Model Phase Wires 1012 1101... - Page 16 TROUBLESHOOTING GUIDE TG27 WARNING: Electric Shock Hazard - the procedures in this TROUBLESHOOTING GUIDE are to be Troubleshooting Guidelines • ELECTRICAL SCHEMATIC. • Grinder Does Not Grind Coffee - None of the Motors Run* Only Some of the Buttons Work. ELECTRIC SCHEMATIC none none...
- Page 17 TROUBLESHOOTING GUIDE TG27 Only Some Buttons Work Coffee Too Course or Too Fine Grinder Adjustment Procedure Grinder Shuts Off Before Brew Basket is Filled PROGRAMMING GUIDE 030818...
- Page 18 TROUBLESHOOTING GUIDE TG29 Grinder Adjustment Procedure WARNING: Electric Shock Hazard - The grinder can be adjusted to make the ground coffee more Setting the Timer Adjustment screw Lock nut Replacing a Broken Shear Disk Housing Burr/ worm feed Look for something that could have gotten caught inside the Shear drive Broken shear...
- Page 19 Return Merchandise Authorization (RMA): All returned equipment must be properly re-packaged in the original carton and received by Curtis within 45 days following the issuance of a RMA. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).
Need help?
Do you have a question about the ILGD-10 and is the answer not in the manual?
Questions and answers