Table of Contents
Advertisement
Quick Links
NorthStar
™
brand
NexGen RIM Tach 6200 MILL-DUTY ENCODER
Key Features
• Stainless Steel and Ductile Cast iron
Construction for a Rugged Heavy Duty
Encoder
• New Sensor Technology provides Extra
Wide Gap for even Higher Reliability
• Extra Heavy Duty Bearings for Long Life
• Convenient LED for Visual indication of
Encoder Functionality
• Foot-Mount or 56-C Face Mount Ideal for
"Flower Pot" or Belt Drive Applications
SPECIFICATIONS
STANDARD OPERATING CHARACTERISTICS
Code: Incremental
Pulses per Revolution: 60-2048
Phasing Sense: A leads B for Counter-Clockwise
rotation (CCW) viewing encoder-mounted end
Quadrature Phasing: 90° ± 45°
Duty Cycle: 50% ± 15%
ELECTRICAL
Input Voltage Requirement: 5-26 Volts DC
Current Requirement: 95 mA typical per sensor
module plus line driver load
Output Signals: 5-26 V Line Driver, 150mA source
or sink
Frequency Response: 0 - 180kHz Data & Index
Electrical Immunity: 2kV ESD, Reverse Polarity,
Short Circuit, Powered Short
Connector: 10 pin industrial duty latching, sealed
NEMA 4 &12, IP65
ELECTRICAL CONNECTIONS
Signal
Connector Pin
Common
1
B
2
A
3
Z *
4
No Connection
5
Vcc
6
—
B
7
—
A
8
—
Z *
9
Shield
10
* Index (Z) optional. See Ordering Information
Worldwide Brands: NorthStar
INNOVATION - CUSTOMIZATION - DELIVERY
WWW.DYNAPAR.COM
Headquarters: 1675 Delany Road • Gurnee,,IL 60031-1282 • USA
Encoder Installation Manual
MECHANICAL
Shaft Speed: 7,000 RPM
Mounting Configuration: 4.5" [115mm]
diameter, 56 C motor face or accessory flange to
meet NEMA MG1-4 standards; foot mount with 4
slotted bolt holes
Housing Material: Cast Iron/Stainless Steel
Acceleration Rate: 3600 rpm/sec max
Shaft : 0.625" (16mm) diameter with standard
key, single or double ended
Shaft Material Options: High Strength Carbon
Steel or Stainless steel
Shaft Axial/Radial Loading:
High Strength Steel: 50 lbf axial, 50 lbf radial
Stainless Steel: 35 lbf axial, 35 lbf radial
Pigtail Cable MS 3102E18-IT#
Black
A
Green
E
D
Blue
C
Violet
—
—
B
Red
Yellow
H
Gray
G
Orange
I
J
Braid
TM
TM
TM
• Acuro
• Dynapar
• Hengstler
Customer Service:
Tel.: +1.800.873.8731
Fax: +1.847.662.4150
custserv@dynapar.com
ENVIRONMENTAL
Operating Temperature Range: -40°C to +100°C
Storage Temperature Range: -40°C to +120°C
Humidity: to 100% RH
Shock (Sensor Module): 1 meter drop test,
30 G's Min
Vibration: 18 G's @ 5-2000 Hz spectrum
TM
TM
• Harowe
Technical Support
Tel.: +1.800.234.8731
Fax: +1.847.662.4150
northstar.techsupport@dynapar.com
NorthStar™ brand is a trademark of DYNAPAR. All rights reserved.
EN 61326
European Sales Representitive
Hengstler GmbH (Germany)
Uhlandstrasse 49, 78554 Aldingen
www.hengstler.com
Document No. 702952-0001, Rev. C ©2012 DYNAPAR
Advertisement
Table of Contents
Related Manuals for NorthStar NexGen RIM Tach 6200
Summary of Contents for NorthStar NexGen RIM Tach 6200
- Page 1 INNOVATION - CUSTOMIZATION - DELIVERY Fax: +1.847.662.4150 Fax: +1.847.662.4150 Uhlandstrasse 49, 78554 Aldingen WWW.DYNAPAR.COM www.hengstler.com custserv@dynapar.com northstar.techsupport@dynapar.com Headquarters: 1675 Delany Road • Gurnee,,IL 60031-1282 • USA NorthStar™ brand is a trademark of DYNAPAR. All rights reserved. Document No. 702952-0001, Rev. C ©2012 DYNAPAR...
-
Page 2: Important Installation Information
IMPORTANT INSTALLATION INFORMATION GENERAL GUIDELINES ELECTRICAL CONNECTIONS (cont.) In some cases, there may be more than one table or Encoders provide quality measurements and long the table may be broken into sections due to different life when common sense, care, and accurate output types. -
Page 3: Led Status Light
IMPORTANT INSTALLATION INFORMATION FEATURES (cont.) LED STATUS LIGHT: When encoders have a differential line driver, there A multicolor LED Status light will indicate to the user are two signals for each of the outputs. Each signal (A, the overall condition of the encoder. The LED is built –... -
Page 4: Mechanical Installation
MECHANICAL INSTALLATION 2.0 Preparation 1.0 Description The NextGen RT 6200 is a high performance and The RT 6200 utilizes a modular construction that reliable Digital Tachometer, designed to provide permits the user to configure the unit as a one or two position and velocity feedback from both AC and DC signal output tachometer. -
Page 5: Foot Mounting
Flexible couplings are generally used to couple the Foot mounting brackets are included on the bottom Model 6200 to its driver (NorthStar part number of the Model 6200. The bolt hole pattern in slotted to RIMFLEX-5858). There are a wide variety of permit a measure of adjustment. -
Page 6: Sensor Module Installation
MECHANICAL INSTALLATION 3.2 Pulley Mounting 4.0 Sensor Module Installation 1. Mounting the Model 6200 onto mounting bracket To install the sensor Module, perform the following with four 3/8-16 UNC bolts through foot mounting steps. See Figure, below. bracket holes. NOTE The mounting bracket should be 1. -
Page 7: Electrical Installation
ELECTRICAL INSTALLATION 5.1 Quick Release Connector Hood 5.0 Wiring Wiring NOTE: Refer to “Important Installation Informa- To install the Quick Release Connector, perform the tion” on pages 2 & 3 prior to wiring the encoder. following steps. Electrical connections are made to the sensor 1. -
Page 8: Ordering Information
Ordering Information To order, complete the model number with code numbers from the table below: Code 4: Shaft Code 5: Electrical Code 6: Termination Code 1: Model Code 2: PPR Code 3: Index Code 7: Options Ordering Information 1 One sensor C Latching Industrial 0060 0480...