Panel Controls And Terminals - Yamaha CBX-K2 Owner's Manual

Panel Controls and Terminals

Front Panel
r t u y
TIME SIGNATURE
SONG
SELECT TOP BOTTOM MEASURE
B
SEQUENCER
STOP CONTINUE START TEMPO
w e
q Keyboard
The CBX-K2 has a 49-key, 4-octave keyboard (C1 to C5),
featuring initial touch (velocity) control. All note on, note
off and velocity data is transmitted via the MIDI OUT
terminal. When used with the C button, the keys are
used for changing various settings and sending special
MIDI messages. (Page 20.)
About the Functions of the CBX-K2: The functions are
divided into two groups: Group A and Group B. The
Group A and B functions are shown on the panel, above
the left section of the keyboard. Several functions can be
used by pressing only the relevant key; in other words,
pressing L is not necessary. These functions, such
as Sequencer Stop and Start, are shown on the panel
without underline.
TIME SIGNATURE
SONG
SELECT TOP BOTTOM
SEQUENCER
STOP CONTINUE
These non-underlined functions can be
used without pressing L.
8
VOICE POLY/ RESET SOUND OFF TG300B CHANNEL DEVICE TOUCH DATA MSB 1ST/ FOOT SW
MAP MONO CONTROL ALL CH RESET MERGE NUMBER SENSITIVITY RPN CONTROLLER NRPN DENSITY LSB 1ST ASSIGN
RESET SYSTEM
PROGRAM WHEEL ASSIGN TRANSPOSE
BANK
PROGRAM GM SOUND XG MERGE MIDI FIXED DRUM
SELECT CHANGE ON OFF ON ON/OFF CH VELOCITY RPN CONTROLLER NRPN NUMBER
q
MEASURE
START TEMPO
i
CONTROLLER CONTROL CHANGE
NUMBER LIST
1 MODULATION 11 EXPRESSION
2 BREATH 64 HOLD1(DAMPER)
5 PORTA TIME
65 PORTAMENTO
6 DATA ENTRY 71 HARMONIC
7 VOLUME 72 RELEASE TIME
PB DATA
10 PANPOT 73 ATTACK TIME
DENSITY DENSITY
74 BRIGHTNESS
84 PORTA CTRL
SLIDER ASSIGN
DRUM
RPN CONTROLLER NRPN NUMBER B 1
The right section of the keyboard serves as value entry
and is used for those functions whose names are under-
lined on the panel and require value entry, such as
Program Change and Tempo.
SONG
SELECT
STOP
These underlined functions require
value entry and pressing L.
Functions whose names appear with a dashed underline
on the panel (for example, GM ON and XG ON) require
pressing L.
CONTROL
These functions with dashed underline
need no value entry, but require pressing
L.
Value entry on the CBX-K2 can be done in two number
systems: Decimal and Hexadecimal. The keys labeled A
through F are for Hexadecimal entry.
NOTE
The normal (default) velocity range of the
CBX-K2 is from 1 to 127. The range differs according
to the Touch Sensitivity setting (pages 19, 28).
o
NRPN
91 REVERB 123 VIBRATO RATE 131 EQ LO FREQUENCY 139 DRUM EG DECAY RATE 147 DRUM HP FILTER CUTOFF
93 CHORUS 124 VIBRATO DEPTH 132 EQ HI FREQUENCY 140 DRUM PITCH COARSE 148 DRUM EQ LO GAIN
94 VARIATION 125 VIBRATO DELAY 133 EG ATTACK TIME 141 DRUM PITCH FINE 149 DRUM EQ HI GAIN
126 LP FILTER CUTOFF 134 EG DECAY TIME 142 DRUM LEVEL 150 DRUM EQ LO FREQUENCY
RPN
127 LP FILTER RESONANCE 135 EG RELEASE TIME 143 DRUM PAN 151 DRUM EQ HI FREQUENCY
120 PB SENSITIVITY 128 HP FILTER CUTOFF 136 DRUM LP FILTER CUTOFF 144 DRUM REVERB
121 FINE TUNE 129 EQ LO GAIN 137 DRUM LP FILTER RESONANCE 145 DRUM CHORUS
122 COARSE TUNE 130 EQ HI GAIN 138 DRUM EG ATTACK RATE 146 DRUM VARIATION
2 3 4 5 6 7 8 9 A B C D E F 0
TIME SIGNATURE
TOP BOTTOM MEASURE
SEQUENCER
CONTINUE START TEMPO
RESET SOUND OFF TG300B
ALL CH RESET
RESET
GM SOUND XG
ON OFF ON
OTHERS
152 CH PRESSURE
153 KEY PRESSURE
154 MASTER VOLUME
156 MASTER TUNING
157 VELOCITY
158 TEMPO
ENTER
HEXA
DECIMAL DECIMAL