Sealey ELECTROSTART E/START3012 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
Wear Eye
manual Protection
1. SAFETY
Read the manufacturer's manual for the vehicle being started: the manufacturer may have specific cautions and instructions regarding
9
emergency starting procedures.
Ensure that the vehicle is in a well ventilated area.
9
Apply the handbrake and select neutral or 'park' before attempting to start.
9
Ensure that the ignition switch and all ancillary electrical equipment is switched off.
9
Keep clear of any pulleys, belts etc. that will move once the engine starts.
9
Take care to ensure correct connection polarity; red clamp to positive, black clamp to negative.
9
Energise the E/start3012 only at ambient temperatures between -30°C and 40°C.
9
When not in use, switch off and store in a cool, dry place out of the reach of children.
9
DO NOT allow this power pack to become wet.
8
DO NOT dismantle this E/start3012: there are no user-servicable parts inside.
8
DO NOT use in explosive atmospheres (e.g. the presence of flammable liquids, gases or dust).
8
DO NOT use the E/start3012 if it appears damaged in any way.
8
DO NOT use this product for any purpose other than that for which it is designed.
8
DO NOT leave in direct sunlight or expose to heat.
8
DO NOT use abrasive or solvent cleaners on this product.
8
DO NOT allow children to play with this product
8
DO NOT allow the positive and negative clamps to touch.
8
Modern vehicles contain extensive electronic systems. Check with the vehicle Manufacturer, for any specific instructions regarding the use of
this type of equipment on each vehicle.
No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.
2. INTRODUCTION
Vehicle jump starting made easy with innovative patented technology. Unlike traditional boosters, it has no internal batteries, as it uses
Ultracapacitors to maximise the discharged battery's voltage. Simply connect to the vehicle's battery, even if discharged, and the unit will draw
enough power to energise itself in a matter of minutes. Power can then be pushed safely back through the starting system to jump start the
vehicle. If the vehicle's battery is faulty or holding less than 5 volts, the ElectroStart range can be pre-charged via another vehicle's battery, a
Micro USB charging cable* (supplied with Model No. E/start3012) or the 12V accessory lead* (excludes Model No. E/START1224 and E/
START3012). Safely store the unit without the need for battery maintenance, and no delay waiting for a battery to charge, the device is ready for
use within minutes. Compact and lightweight for easier handling and storage, yet still delivers the same result as heavy, bulky, lead acid battery
equivalents. Ideal for both professional mechanics and DIY users.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E/START3012
Output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Output Start Peak(EN): . . . . . . . . . . . . . . . . . . . . . . . . 3000A(1500A)
Maximum Starting Capacity: . . . . . . . . . . . . . Petrol; 10ltr, Diesel; 8ltr
Cable & Clamp Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450mm
Size (W x D x H):. . . . . . . . . . . . . . . . . . . . . . . . . 295 x 230 x 90mm
© Jack Sealey Limited
INSTRUCTIONS FOR:
ELECTROSTART® BATTERYLESS POWER
START 3000A 12V
E/START3012
PART NO:
Warning:
Wear
Electricity
Protective
Gloves
Original Language Version
fig.1
E/START3012 Issue:1 - 15/09/17