Issue:
1
Date Issued: 051202
Item Part No.
Description
Item Part No.
1
SA3S/01
Housing
19
SA3S/19
2
SA3S/02
Valve Sleeve
20
SA3S/20
3
SA3S/03
Reverse Valve
21
SA3S/21
4
SA3S/04
Trigger
21
SA3S/21A Hammer Cage, 8.5mm
6
SA3S/06
Screw
22
SA3S/22
7
SA3S/07
Throttle Pin
22
SA3S/22A Hammer Pin, 8.5mm
8
SA3S/08
Steel Ball
23
SA3S/23
9
SA3S/09
Spring
23
SA3S/23A Hammer Dog, 8.5mm
11
SA3S/11
Hose Adaptor
24
SA3S/24
12
SA3S/12
Regulator
25
SA3S/25
13
SA3S/13
O-Ring
26
SA3S/26
14
SA3S/14
Locating Ring
27
SA3S/27
15
SA3S/15
Steel Ball, 3mm
28
SA3S/28
16
SA3S/16
Spring
29
SA3S/29
17
SA3S/17
Anvil Bushing, 32mm
31
SA3S/31
18
SA3S/18
Anvil Collar
32
B/6001
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
SA3/S
PARTS LIST FOR MODEL
Description
Item
Part No.
Description
O-Ring
33
SA3S/33
Rear End Plate
Anvil, 1/2 sq
34
SA3S/34
Pin
Hammer Cage, 8mm
35
SA3S/35
Rear Gasket
36
SA3S/36
Rear Cover
Hammer Pin, 8mm
37
SA3S/37
Washer
38
SA3S/38
Screw
Hammer Dog, 8mm
39
SA3S/39
Protecting Rubber
40
SA3S/40
Oil Seal
Drive Cam
41
SA3S/41
Protecting Rubber
Cylinder Pin
42
SA3S/42
Deflector
Cylinder
43
SA3S/43
Screw
Rotor
44
SA3S/44
Screw
Rotor Blade
45
SA3S/45
Spring
Front End Plate
46
SA3S/46
Pin
Oil Seal
47
SA3S/47
Screw
Bearing
sales@sealey.co.uk
01284 703534
e-mail
www.sealey.co.uk
9A>
INSTRUCTIONS FOR
1/2 SQ DRIVE HEAVY DUTY
AIR IMPACT WRENCH
SA3/S
Model:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
Follow all Health & Safety and general workshop rules, regulations and conditions when using the wrench.
!
WARNING! Disconnect from air supply before changing accessories or servicing.
F
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine
!
parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
F
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use
!
and ensure that all connections are secure.
Only use impact sockets which are specifically designed for use with an impact wrench.
!
Wear approved safety eye/face shield, ear defenders and hand protection.
!
WARNING! Due to the possible presence of asbestos dust from brake linings, when working
F
around vehicle brake systems we recommend you wear suitable respiratory protection.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
!
Keep children and non-essential persons away from the work area.
!
DO NOT use the wrench for a task that it is not designed to perform.
%
WARNING! DO NOT use the wrench if it is damaged or thought to be faulty.
F
DO NOT use wrench unless you have been instructed in its use by a qualified person.
%
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
%
DO NOT operate the wrench if you are tired or under the influence of alcohol, drugs or
%
intoxicating medication.
To avoid unintentional starting DO NOT carry the wrench with your finger on the trigger.
%
DO NOT direct air from the air hose at yourself or others.
%
When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
!
2.
INTRODUCTION & SPECIFICATION
2.1.
Introduction
Superior quality wrench suitable for garage and tyre-shop use. Fitted with rocking-dog type
clutch mechanism with hardened anvil and cage. Features adjustable air/torque control and
reversible action.
2.2.
Specification
Drive . . . . . . . . . . . . . . . . . . . . .1/2sq
Working/Max Torque . . . . .350/400lb.ft
Ultimate Torque . . . . . . . . . . . . 470lb.ft
Air Consumption . . . . . . . . . . . . .4cfm
Operating Pressure . . . . . . . . . . .90psi
Air Inlet . . . . . . . . . . . . . . . . . .1/4BSP
Weight . . . . . . . . . . . . . . . . . . . .2.5kg
Vibration . . . . . . . . . . . . . . . . . . .5m/s
2
Noise . . . . . . . . . . . . . . . . . . .95.5dBA
SA3/S - 1 - 051202