Page 1
Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E1C E1K AVR-X2200W P P P AVR-S910W INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS FOR AVR-X2200W n Audio section n Wireless LAN section • Power amplifier Network type (wireless LAN standard) : Conforming to IEEE 802.11b Conforming to IEEE 802.11g Rated output : Conforming to IEEE 802.11n Front : (Wi-Fi® compliant)z1 95 W + 95 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
TECHNICAL SPECIFICATIONS FOR AVR-S910W n Audio section n Wireless LAN section • Power amplifier Network type (wireless LAN standard) : Conforming to IEEE 802.11b Conforming to IEEE 802.11g Rated output : Conforming to IEEE 802.11n Front : (Wi-Fi® compliant)z1 90 W + 90 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Security : WEP 64 bit, WEP 128 bit 125 W + 125 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
CAUTION IN SERVICING (AVR-X2200W) Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. Press the power button to turn off the power. While holding down buttons "ZONE2 SOURCE" and "DIMMER" simultaneously, press the power button to turn on the power.
CAUTION IN SERVICING (AVR-S910W) Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. Press the power button to turn off the power. While holding down buttons "TUNER PRESET CH +" and "TUNE -" simultaneously, press the power button to turn on the power.
DISASSEMBLY • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "Precautions During Work" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 16
• The photographs with no shooting direction indicated were taken from the top of the unit. • Photos of AVR-X2200W E3 are used in this manual. The viewpoint of each photograph (Shooting direction : X) [View from the top] ↓Shooting direction: B↓...
1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Remove the screws. View from the bottom (2) Remove the screws. Remove the CORD HOLDERs and connector wires. Remove the FFC. CP4400 CORD HOLDER N1008...
2. RADIATOR ASSY Proceeding : TOP COVER FRONT PANEL ASSY RADIATOR ASSY → → (1) Remove the screws. View from the bottom Shooting direction: C Shooting direction: D (2) Remove the screws. Remove the CORD HOLDERs and connector wires. Remove the FFC. CP4400 CORD HOLDER N1008...
3. HDMI PCB Proceeding : TOP COVER HDMI PCB → (1) Remove the screws. Shooting direction: A x2 E3 ONLY (2) Cut the wire clamps, then remove the CORD HOLDERs and connector wires. Remove the FFC. CORD HOLDER x 6 N1033 N1008 (3) Cut the wire clamp, then remove the connector.
4. VIDEO PCB Proceeding : TOP COVER HDMI PCB VIDEO PCB → → (1) Remove the connector. CN5000 CN5000 5. MAIN PCB Proceeding : TOP COVER HDMI PCB VIDEO PCB MAIN PCB → → → (1) Remove the screws. View from the bottom (2) Remove the screws.
6. SMPS PCB Proceeding : TOP COVER SMPS PCB → See "EXPLODED VIEW" for instructions on removing the SMPS PCB. 7. TRANS Proceeding : TOP COVER HDMI PCB TRANS → → See "EXPLODED VIEW" for instructions on removing the transformer (TRANS).
Check the Video/Audio path Mode ↑ video channel. (See page If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur- Remote ID Setup Mode ↑ rently with this device.
Check the Video/Audio path Mode ↑ video channel. (See page If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur- Remote ID Setup Mode ↑ rently with this device.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. then press the "STATUS" button to display the information in section 1.3 on the display. The version list is also displayed on GUI while the version is displayed on the display.
Page 25
i Ethernet 1st Boot Loader, Hardware ID : E t h e r n e t F B L Press "STATUS" button. * * * * * * - b d o Ethernet 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Press "STATUS"...
Page 26
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. Item is displayed. The priority order is w , e , r , t , y , u , q . Condition States Display...
Page 27
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware Version XXXX - XXXX - XXXX...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "TUNER PRESET CH+" and "ZONE2 SOURCE" simultaneously, press the power button to turn on the power.
3.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up AVR-X2200W While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 30
The Video and Audio paths can be checked. The backup data is not rewritten. 3.4.2. Starting up AVR-X2200W While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. AVR-S910W While holding down buttons "TUNER PRESET CH +", "TUNE -" and "TUNE +" simultaneously, press the power button to turn on the power.
Page 31
Paths to be confirmed Display Settings What to confirm Analog Amp Assign Input Source : CBL/SAT ・ Analog input ⇒ Speaker output (Surround Back (ZONE2) L/R) A 0 7 : A S S I G N - Z 2 (Amp Assign : ZONE2) Input Mode : Auto ・...
Page 34
ANALOG AUDIO DIAGRAM fig.02b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANA_FR ANALOG DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 36
ANALOG AUDIO DIAGRAM fig.03b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANA_FR ANALOG DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 38
ANALOG AUDIO DIAGRAM fig.04b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANA_FR ANALOG DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 40
ANALOG AUDIO DIAGRAM fig.05b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANA_FR ANALOG DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 41
ANALOG AUDIO DIAGRAM fig.06 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 42
VIDEO DIAGRAM fig.07 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 43
VIDEO DIAGRAM fig.08 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 44
VIDEO DIAGRAM fig.09 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 45
VIDEO DIAGRAM fig.10 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT uCOM...
Page 47
ANALOG AUDIO DIAGRAM fig.11b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT OTHER AVR1 ONLY PREOUT DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
Page 49
VIDEO DIAGRAM fig.13 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 50
This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.5.2. Starting up AVR-X2200W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 51
(a) ASO/DC protection: Flashes at 0.5-second intervals (0.25 seconds lit, 0.25 seconds unlit) (b) THERMAL (A/B) protection: Flashes at 2-second intervals (1 seconds lit, 1 seconds unlit) 3.6. 232C Standby Clear Mode (AVR-X2200W E3 only) 3.6.1. Actions Switches from 232C standby mode to normal standby mode.
Page 52
This mode enables the unit to display the accumulated operating time, power on count and each protection count. 3.6.2. Starting up AVR-X2200W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 53
This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.7.2. Starting up AVR-X2200W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
4. Remote ID Setup Mode 4.1. Actions This function allows only the desired AV receiver to be operated if multiple DENON AV receivers are used in the same room. 4.2. Starting up AVR-X2200W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
• This mode functions in the same way as normal power-on, except that protections are not activated. 5.2. Operations AVR-X2200W · While holding down buttons "TUNER PRESET CH +", "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
(6) User ID (7) Resume Playback station 7.2. Operations AVR-X2200W · While the power is on, hold down buttons "ZONE2 SOURCE" and "DIMMER" for at least 3 seconds. AVR-S910W · While the power is on, hold down buttons "TUNER PRESET CH +" and "TUNE -" for at least 3 seconds.
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. Order with your dealer for the jigs your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for HDMI PCB ---Items to Be Prepared--- 8U-110084S EXTENSION UNIT KIT 1Sets...
Page 58
(3) Remove the HDMI PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the HDMI PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB VIDEO PCB DIGITAL Insulation sheet CHASSIS-HDMI CONNECTOR...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Proce- dure after PCB Name Ref. No. Description Remark Replace- ment R5F564MJCDFC 32BIT SOFTWARE : Main HDMI U1018 HDMI U1025 MX25L6406EM2I-12G 64M SOFTWARE : DSP1 ROM HDMI U1027...
FIRMWARE UPDATE PROCEDURE 1. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 1.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 61
NOTE : Remove the LAN cable from this unit when performing updates. Download firmware in USB flash drive. 1.5. Start the update AVR-X2200W While holding down buttons "TUNER PRESET CH +" and "STATUS" simultaneously, press the power button to turn on the power. AVR-S910W While holding down buttons "ZONE2 SOURCE"...
Page 62
Mode used when this unit cannot be recovered. Forcibly switches this unit to USB update mode. 1.9.2. Operations AVR-X2200W While holding down buttons the "TUNER PRESET CH +" and "STATUS" buttons simultaneously, insert the AC plug to turn the power on.
Page 63
1.10. About the error codes See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Remedies Code Disconnect and reconnect the USB Unable to detect USB.
Page 64
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Error in Verify after rewriting Main Display stops. If the Display stops at the U p d a t e C h e c k N G (Check Sum Error).
Page 65
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Error notification received while Display stops. If the Display stops at the U p d a t i n g f a i l requesting the Firmware Info.
Page 66
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the Setup failure of the XModem Display stops. If the Display stops at the U p d a t i n g f a i l transfer method.
Page 67
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the No Firmware File in USB. Display stops. If the Display stops at the F i l e s N o t F o u n d Error display, press and hold the "Power operation"...
Page 68
1.11. Device display during the firmware update Display the device being updated and the update progress. Target device USB Update Display Error code when an error occurs 10 - 16 Main CPU 36 - 3D M a i n : * * % * * * m i n 50 - 52 54 - 57...
2. Updating via DPMS Download the latest firmware from our website and update the firmware. 2.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 70
2.3. About the error codes See the following table for details on the error code display, details of the error code, remedies when updating the firm- ware via DPMS. (DPMS : D&M Product Management Server) Error DPMS Update Error Display Details of Error code Remedies Code...
Page 71
Error DPMS Update Error Display Details of Error code Remedies Code Abnormal data in Update Packet Turn off and on the power. Updating received from CY920 (Packet No U p d a t i n g f a i l starts automatically.
Page 72
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry DPMS connection Time Out Error. out the update in an environment that C o n n e c t i o n F a i l 3 9 has little network load.
Page 73
Error DPMS Update Error Display Details of Error code Remedies Code NACK received in response or Turn off and on the power. Updating no response from Sub for the "L" U p d a t i n g f a i l starts automatically.
Page 74
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry IP Address acquisition failure out the update in an environment that C o n n e c t i o n F a i l A 1 (Time Out).
Page 75
Device display during the firmware update Display the device being updated and the update progress. Target device DPMS Update Display Error code when an error occurs 10 - 16 Main CPU M a i n : * * % * * * m i n 36 - 3F 50 - 52 54 - 58...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Contents Connections Playback Settings Tips Appendix Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.”. (v p. 196) Channel output Front Dolby Surround Dolby...
Page 78
Contents Connections Playback Settings Tips Appendix Surround Parameter Audyssey Tone Restorer Sound mode MultEQ® XT Dynamic EQ Dynamic Volume Room Size Center Spread DTS Neural:X Direct/Pure Direct (2-channel) z5 Direct/Pure Direct (Multi-channel) z5 Stereo Multi Ch In Dolby Surround DTS Neural:X Dolby Digital Dolby Digital Plus Dolby TrueHD...
Page 79
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Dolby Dolby Dolby Sound mode NOTE Analog / DTS ES DTS ES Dolby...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator Does the power indicator on on the front panel flash in the front panel flash in red green or white when the when the power is turned on? power is turned on? Is a fuse blown?
2. Analog video COMPONENT / HDMI OUT NG Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI To "3 HDMI/DVI" To "A" <HDMI PCB> test point N1039 N1019 7020-07808-020-0S [MP] N1017 C1295 R1369 C1292 R1374 R1376...
Page 82
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the follow- ing points? HDMI PCB : R2092 Input CVBS : Check B Check the connection between the COMPONENT-Y : R2089 boards. Input COPONENT : Check C COMPONENT-Cb : R2091...
Page 83
Input CVBS Check the settings of each IC. Are the following voltages set? HDMI PCB HDMI PCB faulty. N1039 - 12 pin : Hi (3.3 V) N1039 - 13 pin : Hi (3.3 V) N1039 - 14 pin : Lo (0 V) Extend the HDMI PCB using the jig.
Page 84
Input COMPONENT Check the settings of each IC. Are the following voltages set? HDMI PCB faulty. HDMI PCB N1039 - 11 pin : Lo (0 V) N1039 - 15 pin : Hi (3.3 V) Extend the HDMI PCB using the jig. Is the power voltage being Check the connection between the output correctly?
(7) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (8) When using a DENON Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 86
•Check the circuits around the IP SCALER (U1026, HDMI Is "IP SCALER ERR" displayed? PCB) and DDR2 (U1028/U1029). (See page If there appear to be no problems, U1026 or U1028/1029 is faulty. See "AVR-X2200W-S910W_HDMI Rx-Tx Failure Detection Procedure Manual ver_1.00" of SDI.
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK3 INPUT...
Page 88
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuited? Replace the power transistor. 2SB1560 / 2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47 Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 89
4.3. Analog audio No audio output. Is a voltage of ± 8 V supplied to Repair the ± 8 V power supply. INPUT PCB CN4006? Is there an audio signal in INPUT PCB Repair the power amplifier. CN401? Connect the connectors correctly. Is the connector correctly connected to the HDMI PCB? Repair the HDMI PCB.
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn on the pow- Is the LAN cable correctly inserted? er again. Check the connection environment Set the IP address, etc. correctly. When the static IP address is used, check that no other Are the network settings of this unit correct? devices have the same IP address and that the subnet...
Page 91
Can the NET3.3V output voltage (3.3 V) Is E_POWER1 (U1018 uCOM 132 pin) The circuit of E_POWER1 between to Q1071 (FET-SW) be confirmed? "Hi" ? U1018 and Q1071 are faulty. The circuit around Q1071 (FET-SW) is faulty. Can the NET1.2V output voltage (1.2 V) Is E_POWER4 (U1018 uCOM 132 pin) The circuit of E_POWER4 between to U1070 (DC-DC Conv.) be confirmed?
Page 92
5.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Is the Bluetooth function enabled on the Bluetooth device? Enable the Bluetooth function and try connecting again. Checking the unit Is the Wi-Fi/BT antenna cable inserted correctly into CY920? Connect the Wi-Fi/BT antenna cable correctly.
Page 93
5.3. Cannot recognize the connected USB device Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16- and FAT32-for- Is the USB device supported by this unit? matted mass storage class, MTP-compatible devices and iPod devices (except for some models).
6. SMPS DC 5V is not output. Replace the IC4140 (TOP268VG) and Is IC4140 (TOP268VG) damaged? D4142 / D4143 /D4144 / D4145. Is the fuse (F4140) functioning proper- Replace the damaged part. Is D4142, D4143, D4144, D4145 or IC4140 damaged? Are there any short circuits caused by Repair the short circuited area on the the soldering on the PCB?
Page 96
Operation waveform for each part Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C4148 0.01/250v OPTION OPTION D4142 1N4007 ZD4151 D4143 1N4007 ZD4147 ZJ22B ZJ39B After secondary rectifications ZD4152 D4144 1N4007 ZD4148 ZJ22B ZJ39B D4145...
Page 103
AVR-S910W/X2200W LEVEL DIAGRAM ZONE2 BD34704 from F-ch from DA SB-ch SPEAKER + LINE IN + MAIN NET/USB DAC + ZONE2 (AVRX2200 ONLY) +30dB SP OUT 0dBFS PCM5100 2.0Vrms MAX SIGNAL LEVEL 2.00Vrms +20dB +20dB 0dBFS +10dB -10dBFS +10dB -20dBFS(DIG.IN) -2.0dB LINE IN 200mV -20dBFS...
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR DSP_C EXT_C FRONT V.AUX INPUT PREOUT OTHER AVR1 ONLY DSP_SW EXT_SW AVR_S910 / X2200 : 0.2ch OTHER AVR1 : 7.2ch TUNER VOLUME IC...
CPU LEVEL CHG TO 7B REMOTE3.3V SWM3.3V M3.3V DGND TO 6B SWM3.3V R1366 DGND R1379 R1385 14 13 12 11 10 z OPTION TABLE S910 X2200E3 X2200E2/E1/E1C/K OTHER AVR1U1B/N1B/K R1379 OPEN 0 Ω OPEN 0 Ω R1385 C1298 100N-K OPEN 100N-K OPEN U1016...
TO 8C TO C1 MP OPEN N1034 1.0-16-6PB-2 R2099 R2100 DSP1CS R2079 DSP1MISO DSP1MOSI DSP1CLK R2098 DGND DA3.3V OPTION A 19 18 17 MODEL R1866 R1868 AVR-X2200 OPEN L1129 AVR-S910 OPEN CB05YTYH221 Q2202 RT1N141C OTHER AVR1 OPEN OTHER AVR2 OPEN L1130 CB05YTYH221 R2077...
DIR/A.PLD TO A2 TO A7 TO 2E TO B2 TO D8 TO C2 *FILTER COMPONENTS VALUE TYPE TOLERANCE R1907 680 Ω METAL FILM OR CARBON 0 ¥Ø ≤ 5% 0.068UF FILM OR CERAMIC (CH OR C0G) ≤ 5% C2065 0.0047UF C2067 FILM OR CERAMIC (CH OR C0G) ≤...
CN4701 TO CP4700 OPTION D OPTION A PREOUT N4703 AVR_X2200 E3 : 7P CP4200 CP4201 CP4205 CN4006 TO N1016 TO N1020 TO N1014 TO CP4006 TO CP4007 N4700 1.0-9-4PW OPTION A MODEL AVRS910 AVRX2200 OTHER AVR1 AREA E2/E1C/K U / N / K OPTION A OPTION B OPTION C...
VIDEO PART VIDEO_F/CNT 1/3 JACK5000 Y/V. CVBS OUT C5033 SR ONLY OPEN CVBS INPUT SW NJM2595MTE1 SR ONLY INPUT OUT PUT AVR_S910/X2200 OTHER AVR1 SW4 SW5 MUTE MUTE VIN 3 CBL/SAT CHASSIS VIN 4 VIN 2 NOT USED V.AUX IC5001 NJM2595MTE1 CN5000 C5026...
VIDEO_F/CNT 2/3 FRONT_CNT PART CP3401 TO N1039 CP3401 FUSE F5006,F5007,F5008,F5009 F5005 AVR S910_X2200 OPEN T1.6AL/250V CP5000 OTHER AVR1 CP5000 F5005B F5005A T1.25AL 250V F5005 C5046 TRG_15V_A AVR ONLY (21P) OPEN SR ONLY 25P TO CN5000 CP5003 F5006 T1.6AL 250V F5006A F5006B AC_IN +5V_IN_A...
TUNER / REG PART TO E6 CP4003 OPTION A CP4002 TO CN4003 TO CN4002 AVR_S910/X2200 : 4700UF/25V OPTION D OTHER AVR1 : 6800UF/25V OPTION C CP4006 OPTION B * MODEL / AREA OPTION MODEL AVR-S910 AVR-X2200 OTHER AVR1 E3/E2/E1C/K U/N/K AREA OPTION A OPTION B...
RS_CNT PART (AVR_X2200E3 / OTHER AVR1 ONLY) CP4700 AVR_X2200E3 : 7P SR_5010 : 11P TO CN4701 CP4702 OTHER AVR1 ONLY RS232 PART TO CN4702 AUDIO IN PART (AVR SERIES ONLY) CN4704 PREMUTE_F PRE_SW1 AGND ZONE2_R AGND ZONE2_L MUTE_Z2 AGND CD_R AGND CD_L ZONE2 PREOUT : AVR-S910 EXCEPT...
RS232 PART (AVR_X2200E3 ONLY) CN4702 TO CP4702 SCHEMATIC DIAGRAMS (26/27) SCH26_FRONT_RS232 GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL ANALOG VIDEO DIGITAL VIDEO HDMI STBY POWER...
EXPLODED VIEW Please see the last chapter for the part list. J X3 K X3 29 X2 1차 부착 2차 부착 25X2 J X3 TOPCOVER [SAME AS AVR13SERIES] A X5 A X2 A X6 21 X5 H X21 41-1 G x4 I X2 (INLET) J X2...
PACKING VIEW Please see the last chapter for the part list. *MANUAL POLYBAG ASSY* UK plug ZIPPER BAG (A4size) (UK Only) Notes on RADIO ( ALL ) SAFETY INST. ( ALL ) WARRANTY ( E3 Only ) INSERTION SHEET ( AVR-X2200WE3 Only ) SPK WIRE LABEL ( ALL ) FM ANTENNA ( ALL ) AM ANTENNA ( ALL )
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F564MJCDFC (HDMI : U1018) R5F56108VNFP Terminal Functions Pin Name Symbol Function Pu/Pd STBY...
Page 145
Pin Name Symbol Function Pu/Pd STBY STOP STBY XTAL/P37 XTAL Oscillator connection(12MHz) EXTAL/P36 EXTAL Oscillator connection(12MHz) POWER pin UPSEL/P35(IN)/NMI DSP FLAG3 DSP control pin P34/SCK6/SCK0/IRQ4 BDOWN Power failure detection pin P33/TIOCD0/RXD6/ RC IN Remote control signal input pin RXD0/IRQ3-DS P32/TIOCC0/TXD6/TXD0/ IRQ2-DS TMS/PF3 Unused...
Page 146
Pin Name Symbol Function Pu/Pd STBY STOP STBY DIGITAL AUDIO POWER SUPPLY (DA3.3V) control PC2/RXD5 DA_POWER pin.(ON:H) P75/SCK11 CEC POWER2 CEC STANDBY SUPPLY control pin(CEC STANDBY) DSP ROM rewrite path switching DSP ROM WRITE (DSP rewritten during the "H") PC1/SCK5/IRQ12 DAC.PLD ERR PLD ERROR detection pin POWER pin...
Page 147
Pin Name Symbol Function Pu/Pd STBY STOP STBY DIR DOUT DIR control pin(PCM9211) DA3.3Pu PD6/IRQ6/AN106 DIR CLK DIR control pin(PCM9211) DIR RST DIR control pin(PCM9211) PD5/IRQ5/AN113 788_2_HAINT HDMI MN864788(RX) Audio INT input pin PD4/IRQ4/AN112 Unused DE_RST HDMI ADV7850 RESET control pin PD3/IRQ3/AN111 788_1_HINT HDMI MN864788(TX) HDMI INT input pin...
Page 152
W9864G6KH-5 (HDMI : U1023) W9864G6KH W9864G6KH-5 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0 A11. Column address: A0 A7. 23 ~ 26, 22, A0 A11 Address A10 is sampled during a precharge command to 29 ~35 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 153
W9864G6KH-5 Block diagram CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGIST ER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER COLUMN REFRESH COUNTER COUNTER COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 154
PCM1690 (HDMI : U1048) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — —...
Page 155
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 156
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI:U1052) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 157
ゾーン 3 対応 ゾーン用の 2ch ボリューム搭載 2 線シリアルバスコントロールは、3.3/5V に対応 SQFP-T80C 用途 BD34704KS2 (INPUT : IC4200) AV レシーバ、ホームシアタシステムに最適。 基本アプリケーション回路 Figure 1. 応用回路例 PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL SBLIN INR9(SBRIN2) SRIN INL9(SBLIN2) ○製品構造:シリコンモノリシック集積回路...
Page 158
G Internal 75Ω Driver GENERAL DESCRIPTION PACKAGE OUTLINE G Bipolar Technology G Package Outline DIP16,DMP16 The NJM2586A is a wide band 3-input 1-output 3-circuit video amplifier. It is suitable for Y, Pb, and Pr signal because frequency range is 50MHz.The NJM2586A is suitable for AV receiver, STB, I PIN CONFIGURATION and BLOCK DIAGRAM NJM2595MTE1 (VIDEO:IC5001) and other high quality AV systems.
Page 161
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 163
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 164
D040100087070S C4711,4712 X7R)0.1UF-K/50V-1608REEL D011104577160S C4716,4717 X7R)0.1UF-K/50V-1608REEL D011104577160S C4718,4719 COG)33PF-J/50V-1608REEL D010330167160S OTHER PARTS GROUP BKT4400 AVRX2200WBKE3(DENON) BURRING HOLE SPCC t0.8+SN A4/ 4010210196100SV CLAMP403 HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CLAMP406 HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CN4400 1.0-11S-40PW 40P AN DIP TOP CONTACT L130100114050S CN4402 440MM/6P 20010HS-06=CKM2002HV-06 RD2725#24,28 SH...
Page 166
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 169
7CH_AMP 7CH_AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. E3 : U.S.A.
Page 170
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R467,468 00D9630345903 RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R469 5.6K-J,1/16W-1608REEL C20005626M160S R471 1.2K-J,1/5W-52RE-AX C00001226P520S R473 33K-J,1/5W-52RE-AX C00003336P520S R474,475 00D9630345903 RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R476 2.7K-J,1/5W-52RE-AX C00002726P520S R478 3.3K-J,1W-R.REEL C060033265050S R479...
Page 171
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R623 963252100140D DHPTF1608 471P 105T SMD PTC THERMISTOR F320471001050S R624 RSD-R0-1WJ-4.7K P=5MM SMALL R.REEL N113135647230S R625 150K-J,1/5W-52RE-AX C00001546P520S R627 200K-J,1/5W-52RE-AX C00002046P520S R628 963121006330M 47K-J,1/5W-52RE-AX C00004736P520S R629,630 10K-J,1/5W-52RE-AX C00001036P520S R631 963125012630S 22-J,1W-5REEL C060022065050S...
Page 172
D04010008C050S C513,514 00D9630338402 330UF-M/6.3V,6.3*11-5RE SMS SY D040331081050S C515 00D9630324607 47UF-M/10V,5*11-5RE SMS SY (Pb Free) D040470082060S OTHER PARTS GROUP BKT400 AVRX2200WBKE3(DENON) BURRING HOLE SPCC t0.8+SN A4/ 4010210196100SV CLAMP400,401 HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CN404 180MM/7P 20010HS-07=CKM2002HV-07 YW1007#26 L002181070070S CP401 20010WS-13A00 DIP13P STRAIGHT L101200101310S...
Page 184
EXPLODED REF No. Part No. Part Name Remarks Q'ty New Ver B7-Q481 963219003340S KTC3964/TO126S-BULK J502396400010S C1-Q410 00D9960018706 TR PNP 2SB1560-Y (2SD2390-Y and 2SB1560-Y is one pair parts.) J5011560Y0000S C2-Q446 00D9960018706 TR PNP 2SB1560-Y (2SD2390-Y and 2SB1560-Y is one pair parts.) J5011560Y0000S C3-Q434 00D9960018706...
Page 185
LABEL 5507000019100S LABEL 5507000019110S LABEL 5507000019120S LABEL 5507000019130S LABEL S910 5507000019090S DENON(SPE1C) WARRANTY CARD china 54311016120AD 5727000000440S DENON JP WARRANY Consumers visit (54311004930AD) 5727000002010S TAPE 1220210772000S 963549101000D MIC STAND ASSY 4148210170000S LABEL 5507000019510S 963611501070S AC CORD X2200WE3 L068125130220S 90M-ZC000600R AC CORD X2200WE2...
Need help?
Do you have a question about the AVR-X2200W and is the answer not in the manual?
Questions and answers