Subscribe to Our Youtube Channel
Related Manuals for Hunter Douglas Duette LightLock
Summary of Contents for Hunter Douglas Duette LightLock
- Page 1 Installation Care • Duette Honeycomb Shades ® LightLock System for ™ PowerView Motorization ®...
-
Page 2: Table Of Contents
Removing the Shade (If Necessary) ........9 Removing the Rear Channels (If Necessary) ......9 Questions? Call Hunter Douglas Consumer Support at 1-888-501-8364. © 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners. -
Page 3: Getting Started
Duette ® ™ D-seal © 2018 Hunter Douglas. All rights reserved. All trademarks used Room Side herein are the property of Hunter Douglas or their respective owners. 5109604505 Rev. 11/18 Template Rear Channel Front Channel Bottom End Cap Channel Assembly... -
Page 4: Tools And Fasteners Needed
GETTING STARTED Thank you for purchasing Hunter Douglas Duette Honeycomb Shades. With proper ® installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. -
Page 5: Installation
INSTALLATION Install the Channels Using the outline on the template, determine where to mount the side channel. ■ If your shade is PowerView (battery pack/DC power supply), the minimum mounting ➤ ® depth for flush mount is 2 ⁄ ". Trim the template at the dotted line prior to use. If your shade is PowerView (battery wand —... - Page 6 INSTALLATION Measure and mark the middle groove on each mounting ■ channel starting at 2" from each end and make additional marks located approximately 18" apart. Drill the screw holes in the mounting channels using a ■ ⁄ " drill bit. Test fit the left mounting channel into the window ■...
- Page 7 INSTALLATION Place the mounting channel in the window opening, lining up the rear of the mounting ■ channel to the marks previously made on the side jambs. Attach the mounting channel using the screws provided. ■ Pre-drill holes with a ⁄...
-
Page 8: Install The Brackets
INSTALLATION Reach behind the rear channel and make sure there is ■ no gap between the rear channel and the mounting channel. Repeat for opposite side. ■ Install the Brackets Your order will include the correct number of installation brackets for your shade width, as ■... -
Page 9: Test The Shade
INSTALLATION Test the Shade Test the operation. The shade should be evenly spaced from both rear channels and ■ operate smoothly. For PowerView shades: use the programming button to test the operation and ➤ ® program the PowerView remote. Refer to the Duette Honeycomb Shades PowerView Motorization instructions NOTE: If the channels interferes with the shade's operation, make sure the side channel is installed completely to the mounting channel. -
Page 10: Apply D-Seal (If Necessary)
INSTALLATION Apply D-seal (If Necessary) We have provided adhesive-backed D-seal to reduce any light gaps created by uneven ■ surfaces. Install this as needed to eliminate light gaps. Some recommended areas to apply D-seal include: Entire width of the bottom rail Entire width of the headrail Between mounting channels and mounting surfaces... -
Page 11: Care
CARE Removing the Shade (If Necessary) Start at the bottom of the front channel, pull the channel to separate from the mounting ■ channel. Repeat for opposite side. ■ Lower the shade approximately 4". ■ Bracket While holding the headrail, push ■... - Page 12 2. Visit hunterdouglas.com for additional warranty information, frequently asked questions and access to service locations. 3. Contact Hunter Douglas at (888) 501-8364 for technical support, certain parts free of charge, for assistance in obtaining warranty service or for further explanation of our warranty.
Need help?
Do you have a question about the Duette LightLock and is the answer not in the manual?
Questions and answers