Awesomatix A12 Instruction Manual
  1. Manuals
  2. Brands
  3. Awesomatix Manuals
  4. Motorized Toy Car
  5. A12
  6. Instruction manual

Awesomatix A12 Instruction Manual

1/12-scale electric on-road car
Hide thumbs Also See for A12:
Table of Contents

Advertisement

Quick Links

Download this manual
A12
1/12-SCALE ELECTRIC ON-ROAD CAR

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A12 and is the answer not in the manual?

Questions and answers

Related Manuals for Awesomatix A12

Summary of Contents for Awesomatix A12

  • Page 1 1/12-SCALE ELECTRIC ON-ROAD CAR...
  • Page 2 UAB Awesomatix do reserve all rights to change any specifications without prior notice. All rights reserved. ASSEMBLY NOTES You can find the useful tips of A12 assembling and the A12 editable setup sheet on the Internet site: http://site.petitrc.com/reglages/awesomatix/setupa12/ GENERAL PRECAUTIONS •...
  • Page 3 STEP 1 AM1206 C1205 SH1.5W SH1.5W C1204 SF3X10 SF3X10 Note: SH1.5W is 7.4x3x1.5mm alloy spacer. STEP 2 SB3X5AL x2 SB3X5AL x2 Note: SB3X5AL is 3x5mm alloy screw. AM1203...
  • Page 4 STEP 3 AM1205 AM1205 AM1204 SF3X6 SF3X6 STEP 4 Use blue s thread lock for SS3X4 screw! SS3X4 OR125 SH1.5W OR125 ST1205 ST1205 ST1209L ST1209M Note: Add small amount of a joint grease between ST1205 and ST1209M/L. Rear ball joint Front ball joint Note: SS3X4 set screw tips should just slightly touch AM1204 chassis surface.
  • Page 5 STEP 5 STEP 6 Note: Add 0,3 g of 50 000 100 000 cst silicone oil Note: Add a bit of into groove of ST1202. into cavity of ST1204 damper case. We recommend 1 0 000 cst silicone oil as the base setup Keep ST1204 upright for several minutes until all oil reaches the bottom of the cavity.
  • Page 6 STEP 8 Repeat the STEPS 5,6,7 for other side of ST1204 and check that both ST1202 rotors reached the desirable position (flush with the ST1204 face) Note: These faces of ST1204 and ST1202 should coincide. STEP 9 SB3X5 SB3X5 Note: SS3X10 SS3X10 uring blue...
  • Page 7 STEP 10 ST1201 3mm Ball Stud ST1201 AM1207 ST1203 ST1201 AM1202 STEP 11 Note: ST1201 ball tuds should be placed into slots of ST1202 rotors. SF3X5 x2 SF3X6 x2...
  • Page 8 STEP 12 Note: Assortment of SH shims is used for setting of the desired rear ride height. AT1203 SH0.25 SH0.5 B168ZZ SH1.0 OR15 SH1.75 SS3X5 Stretch OR15 1x5mm o-ring and put it on B168ZZ ball bearing SH0.25 SH0.25...SH1.75 SH0.5 SH1.0 SH1.75 SB3X12 SH0.25...SH1.0...
  • Page 9 STEP 14 1,5mm hex driver or optional RHG 4.2 probe Note: ST1208 steering block posts provide 4 deg caster. Optional ST1208-C5 posts provide 5 deg caster. ST1208 AT1206 The tip of 1,5mm hex driver or optional ST1208 RHG 4.2 probe is used for alignment of the appropriate holes of ST1208 and C1205.
  • Page 10 STEP 16 Note: SPR12FS Front Soft Springs (Silver) and SPR12FM Front Medium Springs (Gold) come in the A12 kit. SH12S-0.2 0.2mm thickness shims are used to set the front spring preload and the front ride height.
  • Page 11 STEP 17 Installation of the standard mini servo. Installation of the SANWA SRG servo. SB3X5AL C1201 SH1.0 SB3X5AL SB3X5AL C1201 SB3X5AL SH1.0 AT1202 ST24-4.0 x2 SH0.25 SB3X6 ST24-4.0 x2 SANWA SRG servo (not included!) AT1202 SH0.25 Servosaver (not included!) SB3X6 Mini servo (not included!) Up to 35x30x15mm mini Servosaver (not included!)
  • Page 12 Rear body holders assembling. STEP 20 Note: Press P06-1 collars into C1203 from lower face of C1203 and apply a drop of CA glue to set them. CA glue (not included) C1203 P06-1 P06-1 Use this hole for the side spring as the base setting. ST1211 Initial position of the side spring.
  • Page 13 STEP 22 Note: Use thin double sided tape to secure P1215 foam bumper on C1204 bumper plate. P1215 P14-2 P14-2 P14-2 P14-2 SB3X10 Motor (not included) SB3X10 SF3X10 SF3X10 SH0.25 SH0.25 SB3X8 SB3X10 STEP 23 Note: Use OR91 9x1mm o-ring with the thick spur gears.
  • Page 14 STEP 24 SC25X8 AT1207 SH12R3.5 SH12R2.0 SC25X8 SH12R0.5 Note: The second SC25X8 M2.5x8 screw is used for perfect axle balancing of the left wheel hub. SH12R0.5 SH12R2.0 Note: The second SC25X8 M2.5x8 screw is used for Note: The set of SH12R*** spacers shown ensures perfect axial balancing of the left wheel hub.
  • Page 15 STEP 25 STEP 26 Note: Combination of SH12F0.5 spacers on both sides of the front wheel is used for the front width adjustment. Front 1/12 wheel (not included) B156 SH12F0.5 B156 SB3X5 Pinion gear (not included) Rear 1/12 wheel (not included) SC3X5 x3 SC3X6 x3 Note:...
  • Page 16 RHG 4.2 gauge is designed for s and measuring the ride height under rear damper of the A12 car DRH - Damper Ride Height) and can be also used for s and measuring of the front ride height (FRH) and the rear ride height (RRH).
  • Page 17 These beams act as springs when the screws in them press on the AM1204 chassis plate. A12 setup sheet includes two values for the rear ride height. DRH 1 shows the ride height resulting from side spring pressure only, without the use of AM1205 side beams. DRH ride height is the final ride height of the car (which can be a combination of both side springs and side bars to reach this final desired height).
  • Page 18 SETUP SHEET DATE AIR / TRACK NAME COUNTRY TRACK CONDITION RACE TRACTION TRACK SUSPENSION PLATE STEERING HUB POST C1205 ST1208 C1205-ZT ST1208-C5 SERVO C1205AL C1201 STEERING B OCK C1205AL-ZT C1 01-Z AT1204 A 1 04-Z FO M BUM ER P1215 BUMPSTEER AM1 05 BODY HOLDER SHIMS...
  • Page 19 Bumper Plate SF3X10 M3x10 Flat Head Screw C1205 Suspension Plate SB3X5AL M3x5 Alloy Screw SPR12FS Front Spring Soft STS-A12 A12 Stickers Sheet SPR12FM Front Spring Medium SIO100K 100k silicone oil Optional parts Parts # Description RHG 4.2 Ride Height Gauge...
  • Page 20 WWW.AWESOMATIX.COM AWESOMATIX Email: support@awesomatix.com All rights reserved. Copyright UA Awesomatix 2020.

Table of Contents