Advertisement
Quick Links
Security Cage Kit
Groundsmaster
Unit with 2 Post ROPS Extension
Model No. 31606
This kit fits 2-Post ROPS Extension Kit Model 31351 only.
Note:
Determine the left and right sides of the machine from the normal operating position.
Note:
Have an assistant help you to install this kit.
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface.
2.
Lower the cutting units.
3.
Engage the parking brake.
4.
Shut off the engine and remove the key.
5.
If there are lights on the roll bar, remove the lights and mounting hardware from the roll bar.
Retain the lights and the mounting hardware
6.
If a 2 Post ROPS extension was installed on the machine, remove the side panels that are used to
mount the ROPS post lights
Note:
Retain the ROPS clamps and corresponding hardware.
7.
Position the control console to the furthest inward position.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
4500, 4700, or Reelmaster
(Figure
2).
Register at www.Toro.com.
Form No. 3419-943 Rev B
®
7000 Series Traction
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3419-943* B
Printed in the USA
Advertisement
Related Manuals for Toro Security Cage Kit
Summary of Contents for Toro Security Cage Kit
- Page 1 Form No. 3419-943 Rev B Security Cage Kit Groundsmaster ® 4500, 4700, or Reelmaster ® 7000 Series Traction Unit with 2 Post ROPS Extension Model No. 31606 Installation Instructions This kit fits 2-Post ROPS Extension Kit Model 31351 only. Note: Determine the left and right sides of the machine from the normal operating position.
- Page 2 Procedure Refer to Figure 2 as you perform the following steps. Note: Ensure that all parts are assembled loose. Assembling the Cage Complete the assembly of the kit; then, tighten all fasteners. Use bolts (5/16 x 3/4 inch) and flange nuts (5/16 Parts needed for this procedure: inch) to secure the left and right door supports to the top rails of the 2 Post ROPS Extension.
- Page 3 g205385 Figure 1 Left side shown 1. Drill holes—0.281 inch 3. Left lower-panel assembly 2. Foot platform Secure the left and right door cage assemblies to the corresponding side of the machine. Place the hinge assembly connected to each door onto the previously installed door-mount assemblies with 4 spacers.
- Page 4 g211833 Figure 2 1. Flange nut (5/16 inch) 10. Left door mount 19. Flange nut (1/4 inch) 2. Left door support 11. Right door mount 20. Bolt (5/16 x 3/4 inch) 3. Right door support 12. Upper mount bracket 21. Roll bar 4.
- Page 5 Tighten the jam nut onto the latch pin by hand (Figure Assembling the Door Latch Parts needed for this procedure: Adjusting the Door-Latch Jam nut Pins Pin guard Latch-pin cam No Parts Required Thrust washer Lock washer Procedure Latch pin Center the latch pin in the latch-pin-mount bracket on the rail (Figure...
-
Page 6: Adjusting The Doors
Note: If the height measured is more than the zone specification, rotate the latch-pin cam 45° toward the inside of the cab to achieve the specified measurement. If the height measured is less than the zone specification, perform the Adjusting the Doors opposite of the above procedure. -
Page 7: Installing The Windshield
Procedure Refer to Figure 7 as you perform the following steps. Note: Ensure that the upper windshield is installed so Installing the Windshield that the seam is positioned on the bottom of the frame. Install the dual-tab mount between the upper and lower windshield frame on the ROPS. -
Page 8: Completing The Installation
Completing the Installation No Parts Required Procedure Ensure that all fasteners are tightened. Install any attachments that you previously removed, such as lights, onto the left and right panels.