Table of Contents
Advertisement
Warnings:
1. Misuse of the water dispenser or failure to follow directions may result in serious
personal injury.
2. DO NOT use the water dispenser if it is not in its upright position.
3. DO NOT use the water dispenser for anything other than carbonating water. Use of the
water dispenser for any unintended purposes may result in serious personal injury.
4. Use the water dispenser on a flat, stable surface away from heat sources and do not
leave in direct sunlight.
5. DO NOT place the water dispenser on a hot surface (e.g. kitchen oven/stove/ hob) and
never use it close to a flame.
6. DO NOT move the water dispenser during the carbonation process.
7. To reduce the risk of personal injury or property damage, any servicing or repair
should be performed by a ReadyRefresh authorized service representative.
8. ONLY dispense sparkling water into vessels approved for carbonated beverages.
Sealed containers may burst if not rated for pressurized use.
9. Close adult supervision is necessary when the water dispenser is used by children and
it is not recommended for use by children under 5 years of age.
I. Operating Conditions:
1. Working Voltage: AC115V±10%, 60Hz;
2. PCB Storage Temperature: -10℃～55℃; Operating Temperature: 0℃～35℃.
II. Display and Buttons:
Allure Sparkling Water Dispenser
User Manual
Rev. A - 060220
Advertisement
Table of Contents
Summary of Contents for ReadyRefresh Allure Series
- Page 1 6. DO NOT move the water dispenser during the carbonation process. 7. To reduce the risk of personal injury or property damage, any servicing or repair should be performed by a ReadyRefresh authorized service representative. 8. ONLY dispense sparkling water into vessels approved for carbonated beverages.
- Page 2 Rev. A - 060220 III. Buttons and Indicators Function: 1. Sparkling Water Dispense/Reset Button: After selecting the desired sparkling level on the display, press and hold the large green button to dispense sparkling water. If the green light is flashing, a reset is required. Follow the instructions in the Troubleshooting section.
- Page 3 Rev. A - 060220 This will be known by an increase in dispense pressure. 8. While the cooling status indicator flashes, the dispenser is chilling the still and sparkling water. When the cooling status indicator stops flashing and remains steady, the cold water has reached its ideal temperature setting.
- Page 4 Rev. A - 060220 8. Fill the cold tank with clean bottled water 9. Plug the dispenser back into a power outlet, and drain the cold tank again completely. 10. Clean the no-spill adapter and baffle (previously removed) by washing both with warm soapy water.
- Page 5 The cleaning process is complete. Contact Customer Service at (800) 274-5282 to learn more about the ReadyRefresh™ Professional Cleaning Service. Our dedicated ReadyRefresh™ Technicians use professional-grade cleaners and equipment to employ a unique process that thoroughly cleans water dispensers.
- Page 6 From elsewhere holes or damage. Place a new bottle onto the dispenser and monitor for leaks If leaks continue, contact your ReadyRefresh Service Center If the CO2 cylinder is empty, water will not be sparkling. If the “Replace CO2” light is flashing, replace the CO2 cylinder with a new one.
- Page 7 Hissing is heard Install a new cylinder and monitor for additional hissing. If hissing is still heard, contact your ReadyRefresh Service Center. TECHNICAL APPENDIX VII. Temperature Control: 1. The hot water temperature is controlled by mechanical thermostats, keeping the water temperature between 178⁰...
- Page 8 Rev. A - 060220 IX. Airlock Release Program: 1. If the booster pump is running for more than two minutes, but the float switch does not become engaged, the sparkling water reservoir will become airlocked with CO . This is caused by continuously pressing the dispense button with no water available, or if the dispenser is improperly setup.
Need help?
Do you have a question about the Allure Series and is the answer not in the manual?
Questions and answers