Related Manuals for Teknik Boulevard Cafe Desk 5420701
Summary of Contents for Teknik Boulevard Cafe Desk 5420701
- Page 1 Teknik www.teknikoffice.co.uk Business or pleasure. Works both ways. Boulevard Cafe Desk Model 5420701 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-21 Français 22-24 Skip the power trip. This time. Español 25-27 Safety 28-30 Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) SHELF (1) DRAWER BOTTOM (1)
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) HIDDEN EXTENSION RAIL - 6 EXTENSION SLIDE - 6 CAM - 12 SCREW - 12 FILE FILE PULL - 3 ADJUSTABLE GLIDE - 8 GLIDE - 4 HANGER - 4... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Some assembly Fasten a BACK (G) to the RIGHT END (A) and RIGHT å (and snacks) required. UPRIGHT (C).
- Page 6 Step 2 Fasten the other BACK (G) to the LEFT END (B) and LEFT å UPRIGHT (D). Use eight BLACK 5/16" WAFER HEAD SCREWS (19). NOTE: You should start each SCREW a few turns before å completely tightening any of them. BLACK 5/16"...
- Page 7 Step 3 Fasten the MODESTY PANEL (I) to the UPRIGHTS (C å and D). Use eight BLACK 5/16" WAFER HEAD SCREWS (19). NOTE: You should start each SCREW a few turns before å completely tightening any of them. BLACK 5/16" WAFER HEAD SCREW (8 used in this step) The tabs should be located here.
-
Page 8: Black 1-5/8" Wafer Head Screw
Step 4 NOTE: You may need someone's help in this step. å Fasten the ENDS (A and B), UPRIGHTS (C and D), and å BACKS (G) to the TOP (E). Use twelve BLACK 1-5/8" WAFER HEAD SCREWS (12). NOTE: You should start each SCREW a few turns before å... - Page 9 Step 5 Fasten the SHELF (H) to the LEFT END (B) and LEFT å UPRIGHT (D). Use four BLACK 1/2" WAFER HEAD SCREWS (15). NOTE: You should start each SCREW a few turns before å completely tightening any of them. The arrow should be here.
-
Page 10: Black 3/4" Hex Head Screw
Step 6 Fasten the BOTTOMS (F) to the ENDS (A and B) and å UPRIGHTS (C and D). Use eight BLACK 3/4" HEX HEAD SCREWS (14) and tighten with the L-WRENCH (11). NOTE: You should start each SCREW a few turns before å... -
Page 11: Black 1/2" Machine Screw
Step 7 Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be å prepared, the parts are greasy. Fasten six EXTENSION RAILS (1) to the ENDS (A and B) and UPRIGHTS (C and D). Use twelve BLACK 1/2" MACHINE å... - Page 12 Step 8 Turn eight ADJUSTABLE GLIDES (8) into the bottom of å the ENDS (A and B) and UPRIGHTS (C and D). Now might be a good time to refresh NOTE: Turn the ADJUSTABLE GLIDES completely in. å your drink. Final adjustments will be made after the unit is standing upright.
- Page 13 Step 9 Push twelve HIDDEN CAMS (3) into the DRAWER å SIDES (L and M) and LARGE DRAWER SIDES (P and Q). Arrow Arrow Hole The arrow in the HIDDEN CAM must point toward the (12 used) hole in the edge of the board. Page 13...
- Page 14 Step 10 Turn twelve CAM SCREWS (4) into the exact holes shown å in the DRAWER FRONTS (J and K). (12 used) Page 14...
- Page 15 Step 11 Groove These edges of the DRAWER SIDES should be closer to the bottom edge of the DRAWER FRONT. Fasten the DRAWER SIDES (L and M) to the DRAWER FRONT (J). Tighten four HIDDEN CAMS. å With the palm of your hand, tap the DRAWER BOTTOM down into the grooves.
-
Page 16: Black 3/8" Machine Screw
Step 12 Fasten two EXTENSION SLIDES (2) to the DRAWER SIDES (L å and M). Use six BLACK 1/2" PAN HEAD SCREWS (17). Peel four STICKERS from the APPLIQUE CARD (9) and stick å one onto each HIDDEN CAM in the drawer. Fasten the PULL (7) to the DRAWER FRONT (J). -
Page 17: Black 1-1/2" Flat Head Screw
Step 13 Groove These edges of the LARGE DRAWER SIDES should be closer to the bottom edge of the LARGE DRAWER FRONT. Fasten the LARGE DRAWER SIDES (P and Q) to the LARGE DRAWER FRONT (K). Tighten four HIDDEN CAMS. å... -
Page 18: Black 1/2" Pan Head Screw
Step 14 Fasten two EXTENSION SLIDES (2) to the LARGE DRAWER å SIDES (P and Q). Use six BLACK 1/2" PAN HEAD SCREWS (17). Peel four STICKERS from the APPLIQUE CARD (9) and stick å one onto each HIDDEN CAM in the large drawer. Fasten the PULL (7) to the LARGE DRAWER FRONT (K). - Page 19 Step 15 Push two FILE GLIDES (5) onto the LARGE DRAWER å SIDES (P and Q). Place two FILE HANGERS (6) onto the FILE GLIDES (5) on å the LARGE DRAWER SIDES (P and Q). Repeat this step for the other large drawer. å...
- Page 20 Step 16 Carefully stand your unit upright. å Pro Tip: Lift with your Peel the BUMPERS from the BUMPER CARD (10) and å legs. And, you know, stick them onto the front edge of the SHELF (H). your arms. Page 20...
-
Page 21: Adjustable Glide
Step 17 Position your unit in its fi nal location. å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the å ADJUSTABLE GLIDE clockwise. To insert the drawers into your unit, line up the EXTENSION SLIDES on the drawers with the EXTENSION RAILS on the å... - Page 22 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...
Need help?
Do you have a question about the Boulevard Cafe Desk 5420701 and is the answer not in the manual?
Questions and answers