Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
ATCA-3671
FPGA Module for ATCA
This document describes how to install, configure, and test the ATCA-3671 FPGA Module for
ATCA. The ATCA-3671 is programmable both through LabVIEW using LabVIEW FPGA and
through BEEcube Platform Studio (BPS).
Note
If you are using BPS, visit
to access BPS-related resources within the BPS Support Community.
This icon denotes a caution, which advises you of precautions to take to avoid injury,
data loss, or a system crash.
Caution
a manner not described in this document.
Contents
Electromagnetic Compatibility Guidelines............................................................................... 2
Verifying the System Requirements..........................................................................................2
Unpacking the Kit..................................................................................................................... 3
Verifying the Kit Contents................................................................................................ 3
Preparing the Environment....................................................................................................... 5
Installing the Software.............................................................................................................. 5
Installing the Hardware............................................................................................................. 6
Protection Impairment.......................................................................................................6
Installing the RTM............................................................................................................ 6
Installing the ATCA-3671 Module................................................................................... 7
Installing AIO-3681/3682 Modules.................................................................................. 7
Installing AIO-3691 Modules......................................................................................... 12
Powering On the ATCA-3671 Module................................................................................... 15
Maximum Power Requirements......................................................................................16
Connecting to a Host Computer..............................................................................................17
Installing MXI Cables..................................................................................................... 17
Identifying FPGA Devices in MAX............................................................................... 17
Network Connection Configuration to the ATCA-3671................................................. 18
Programming...........................................................................................................................18
Finding Example VIs...................................................................................................... 18
Verifying the Device Connection (Optional).................................................................. 18
You can impair the protection provided by the ATCA-3671 if you use it in
ni.com/info
and enter the Info Code
BPSsupport
Advertisement
Table of Contents
Related Manuals for National Instruments ATCA-3671
Summary of Contents for National Instruments ATCA-3671
-
Page 1: Table Of Contents
GETTING STARTED GUIDE ATCA-3671 FPGA Module for ATCA This document describes how to install, configure, and test the ATCA-3671 FPGA Module for ATCA. The ATCA-3671 is programmable both through LabVIEW using LabVIEW FPGA and through BEEcube Platform Studio (BPS). Note If you are using BPS, visit ni.com/info... -
Page 2: Electromagnetic Compatibility Guidelines
The length of any cable connected to any other port must be no longer than 3 m (10 ft.). Verifying the System Requirements To use the NI ATCA FPGA Modules instrument driver, your system must meet certain requirements. 2 | ni.com | ATCA-3671 Getting Started Guide... -
Page 3: Unpacking The Kit
Verifying the Kit Contents • ATCA-3671 module • Ethernet cable • ATCA I/O slot blockers (x4) • ATCA-3671 Getting Started Guide (this document) Note Your ATCA-3671 kit may contain additional NI ATCA products. ATCA-3671 Getting Started Guide | © National Instruments | 3... - Page 4 M2.5x8 screws (x2) – M2.5x6 screws (x2) • AIO-3682 Signal Generator Module for FMC, with the following components: – Riser card (x1) – Male-to-female M2.5 standoffs (x4) Included in some ATCA-3671 kits. 4 | ni.com | ATCA-3671 Getting Started Guide...
-
Page 5: Preparing The Environment
– M2.5x8 screws (x2) – M2.5x6 screws (x4) Preparing the Environment Ensure that the environment you are using the ATCA-3671 in meets the following specifications. Ambient temperature range 0 °C to 40 °C (IEC 60068-2-1, IEC 60068-2-2) Operating temperature range Used with a Single-Module ATCA 0 °C to 25 °C... -
Page 6: Installing The Hardware
Installing the Hardware Protection Impairment Caution You can impair the protection provided by the ATCA-3671 if you use it in a manner not described in this document. Caution Do not operate the ATCA-3671 in a manner not specified in this document. -
Page 7: Installing The Atca-3671 Module
Determine how many modules you are installing and choose the appropriate number of empty slot(s) in the ATCA-3671. If hardware is present in the slot(s) you choose, remove the installed ATCA I/O module(s), riser card(s), and additional components from the slot(s). - Page 8 Complete the following steps to install one to four AIO-3681/3682 modules, depending on your chosen hardware configuration. Install a riser card into the ATCA-3671 motherboard mating connector. Secure with two male-to-female M2.5 standoffs (10 mm hex length, 6 mm thread length), as shown in the following figure.
- Page 9 Align the AIO-3681/3682 module with the riser card connector and gently mate the connectors, as shown in the following figure. Note The AIO-3681/3682 module must be centered on the riser card connector so that the holes for the screws are aligned. ATCA-3671 Getting Started Guide | © National Instruments | 9...
- Page 10 1. ATCA-3671 Module 2. Riser Card 3. AIO-3681/3682 Modules Secure the AIO-3681/3682 module to the ATCA-3671 module with two M2.5x8 screws from the underside of the ATCA-3671 module, as shown in the following figure. 10 | ni.com | ATCA-3671 Getting Started Guide...
- Page 11 Figure 7. Securing the AIO-3681/3682 Module(s) to the ATCA-3671 Module and Riser Card(s) - 3 6 l e f 1. ATCA-3671 Module 2. M2.5x8 Screw Secure the AIO-3681/3682 module to the riser card with two M2.5x6 screws into the riser card standoffs, as shown in the following figure.
-
Page 12: Installing Aio-3691 Modules
Determine how many modules you are installing and choose the appropriate number of empty slot(s) in the ATCA-3671. If hardware is present in the slot(s) you choose, remove the installed ATCA I/O module(s), riser card(s), and additional components from the slot(s). - Page 13 Complete the following steps to install one to four AIO-3691 modules, depending on your chosen hardware configuration. Install two female-to-female standoffs in the ATCA-3671 module with two M2.5x8 screws installed from the underside of the ATCA-3671 module as shown in the following figure. Figure 9. Installing Standoffs 1.
- Page 14 2. AIO-3691 Modules Secure the AIO-3691 module with two M2.5x6 screws installed from the underside of the ATCA-3671 module and two M2.5x6 screws installed from the top of the AIO-3691 module, as shown in the following figure. 14 | ni.com | ATCA-3671 Getting Started Guide...
-
Page 15: Powering On The Atca-3671 Module
The ATCA-3671 requires a -48 V external power supply that meets the product specifications. Ensure the power source is turned off. Connect the DC power supply to the ATCA-3671 back panel, as shown in the following figure. ATCA-3671 Getting Started Guide | © National Instruments | 15... -
Page 16: Maximum Power Requirements
The ATCA-3671 powers on automatically once the DC power supply is connected to the power source. Observe the colored LEDs on the front panel of the ATCA-3671 to check the device status, as described in the following table. Table 1. LED State while Powering On the ATCA-3671... -
Page 17: Connecting To A Host Computer
Installed devices appear under the name of their associated chassis. Find additional information, such as the model and serial number of the ATCA-3671 main board, as well as the FPGA ID of the connected FPGA, by selecting any ATCA-3671 FPGA device and opening the Settings window. -
Page 18: Network Connection Configuration To The Atca-3671
Network Connection Configuration to the ATCA-3671 An Ethernet connection to the host computer is required to use the ATCA-3671 hardware. The ATCA-3671 is shipped with the following fixed network configuration: • IP address: 192.168.0.75 • Subnet mask: 255.255.255.0 • Gateway address: 192.168.0.1... -
Page 19: Removing Modules
Removing the ATCA-3671 Module Disconnect all cables from the ATCA-3671 module. Loosen the four captive screws on the front panel of the ATCA-3671 module. Push up on the latch and rotate the ejector handle away from the module to unseat the backplane connectors to open the ejector handles. - Page 20 ATCA-3671 has powered on. Caution Connections that exceed any of the maximum ratings of any connector on the ATCA-3671 can damage the device and the chassis. NI is not liable for any damage resulting from such connections. Table 4. ATCA-3671 Front Panel LEDs...
- Page 21 Blinking A fault has occurred on the board. Solid The power has failed. Blue Blinking The module is powering off. Solid The module is fully powered off. It is safe to remove the ATCA-3671 from the chassis. ATCA-3671 Getting Started Guide | © National Instruments | 21...
- Page 22 The GPIO connector accepts a standard, third-party Mini HDMI cable, but the GPIO port is not a Mini HDMI interface. Do not connect the ATCA-3671 to another device using the GPIO port as a Mini HDMI connection. NI is not liable for any damage resulting from such signal connections.
-
Page 23: Rtm-3661 Front Panel
ATCA-3671 has powered on. Caution Connections that exceed any of the maximum ratings of any connector on the ATCA-3671 can damage the device and the chassis. NI is not liable for any damage resulting from such connections. ATCA Compatibility vs. Compliance The ATCA-3671 achieves mechanical and electrical compatibility with the ATCA (Advanced Telecommunications Computing Architecture) 3.0 specification, and it is intended for use with... -
Page 24: Why Doesn't The Device Appear In Max
Why Doesn't the Device Appear in MAX? If you cannot find the ATCA-3671 in MAX, complete one or more of the following steps. • Restart the host computer to reset the MXI connection. • Ensure you have the correct version of NI ATCA FPGA Modules installed on the host computer. -
Page 25: Worldwide Support And Services
United States, visit the Worldwide Offices section of ni.com/ niglobal to access the branch office websites, which provide up-to-date contact information, support phone numbers, email addresses, and current events. ATCA-3671 Getting Started Guide | © National Instruments | 25... - Page 26 NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at . You can find patents.txt ni.com/patents...
Need help?
Do you have a question about the ATCA-3671 and is the answer not in the manual?
Questions and answers