Advertisement
Advertisement
Table of Contents
Related Manuals for PEUGEOT 208 R2
Summary of Contents for PEUGEOT 208 R2
- Page 1 USER GUIDE SYSTEM Update : 7 of August 2019 www.peugeotsport-store.com...
-
Page 2: Table Of Contents
Summary - Global system overview Looms……........................- Mandatory sensors......................- Driver system overview Functions………………………………………………………………………………………………………… - Driver’s overview………….………………………………………………………………………………….. - Dashboard display……………………………………………………………………………………………. Gearbox…………………………………………………………………………..……………………..….…… - CAN connexion lost…………………………………………………………………..………….………… Accessories………………………………………………………………………..……......Calibration………………………………………………………………………………………………………. - Display pages……………………………………………………………..………………………....- Alarm messages.…………………………………………………………….………….……………………. - Wintax4 information - Channel list…………………………………………………………………………………………....- BRK outputs………………………………………………………………………........ -
Page 3: Looms
Global system overview - Looms... - Page 4 Global system overview – essentials sensors Essentials sensors : The following sensors are essentials for the smooth operation of the car. If one them is not working it may generate some engine and gearbox trouble : Barrel position Throttle pedal position ...
-
Page 5: Functions
Functions Gearbox lock ( R←N←1 ) Dashboard display GB’s control : Pull => upshift Push => downshift High beam / Dipped beam // Flash Wipper’s speed... - Page 6 Functions - BRK Power Throttle mapping (throttle :1->2->3->2->1) Mode : Road / Stage Surface : Gravel / Tarmac Unused Blinkers // Simultaneous right and left press = hazard light One press => working during 25s (Hazard light stops if press on left or right) Scroll pages Short press =>...
-
Page 7: Driver's Overview
Driver overview Reverse gear unlock command Press the button and use the gearbox shift Disabled over 30km/h and 3500rpm Necessary for : 0 R and 1 0 Pedal / throttle body mapping Several pedal / throttle body mapping are available in stage mode : ... -
Page 8: Dashboard Display
Dashboard display Information given by the dashboard display Rev information LED1 to 4, approaching the upshift rev Progressive lightening of LED 1 to 4 LED 5 => time to shift LED 6 => over rev ... -
Page 9: Gearbox
Gearbox Barrel position If the barrel position sensor is replaced, the following procedure must be followed: Make sure the gearbox is mechanically in neutral gear then turn the sensor until you have the voltage between 0.995 V and 1.005 V on the first "mechanic" page. Incorrect adjustment of the position of the barrel sensor can lead to difficulties in shifting and a reduction in the service life of the gearbox parts. -
Page 10: Can Connexion Lost
However once the car is turned off it can be impossible to restart because the ECU does not have the engine rev information. If this loss is related to the ECU, replacing it will solve the problem. Only a technical adviser from Peugeot Sport has the equipment to reload an acquisition table in an ECU. ... -
Page 11: Accessories
Accessories Fuel pump Operation during 10 seconds after a press on Power; Operation when the engine is running ; The pump can be forced to drain the fuel tank: Power OFF, hold down the Aux button and press Power. Radiator fan(s) ... -
Page 12: Calibration
Throttle body and pedal calibration Before the calibration Engine stop ; Gearbox in neutral gear. Procedure Main switch OFF ; Depress the accelerator pedal fully and hold; Main switch ON ; Wait for a message to appear on the dashboard; ... - Page 13 Display – Starting page Software’s name Display configuration’s name...
- Page 14 Display – Stage mode Mode Surface Gear engaged Throttle mapping selected Engine rev Lights Water Oil pressure alarm temperature pressure Water temperature alarm...
- Page 15 Display – road mode Lights Speed (km/h) Throttle pedal (%) Throttle body ( ° ) Front and rear brake pressure (bar) Brake pads temperature (option - °C ) Fuel consumption (L) Gear engaged Engine rev...
- Page 16 Display – Mechanic mode Barrel sensor setting Gear engaged Tension on the two barrel’s strips In case of replacement of the barrel sensor, you must follow the procedure explained bellow : - Make sure the gearbox is mechanically in neutral gear. - Unscrew a little the two screws of the sensor then turn it until the voltage displayed on the first page "mechanic"...
- Page 17 Display – Mechanic mode Diagnosis Engine diagnosis Spark plug not connected : one of these icons will be displayed at the top right of the screen with the number of the spark plug concerned. Cylinder 1 is on the flywheel side. Synchronisation •...
- Page 18 Diagnosis Icons Lambda (option) Right blinker Day lights Radio Rear anti fog light Left blinker Tripmaster Horn Reverse light Front anti fog Reverse gear unlock Low beam Map light Injection Radiator fan Stop light Parking lights Throttle body Starter Ramp of headlight Fuel pump Electrical...
- Page 19 Display – Mechanic mode Engine / Gearbox check Front right speed Front left speed Barrel voltage Oil pressure Atmospheric pressure Battery voltage Water temperature Reverse gear unlock Intake air temperatures Richness (if optional lambda sensor fitted) Throttle pedal (%) Throttle body (°) Switch upshift Gear engaged Engine rev...
- Page 20 Display – Mechanic mode Chassis Front brake pressure Front left speed Front right speed Rear brake pressure Car speed* Throttle pedal (2 strips) Throttle body (2 strips) Steering angle (option) Barrel voltage (2 strips) Gear engaged * : car speed is calculated in relation to other wheel speeds...
- Page 21 Display – Mechanic mode BRK console Auxiliaries functions reminder Throttle mapping BRK’s button check: BRK’s function check : must appear is the function is activated must appear if the button is pressed Warning : some function are only activated with POWER ON...
- Page 22 Messages and alarms ALARMS Parameter Condition Secondary Condition Message Learning throttle Apprento >= 4 ROAD N=0 VEH=0 THROTTLE Learning throttle max Apprento >= 3 ROAD N=0 VEH=0 PED MIN Learning throttle min Apprento >= 2 ROAD N=0 VEH=0 PED MAX High water temperature alarm TEAU >= 110°C WATER...
- Page 23 Wintax : Channel list - 1 Nom du canal Unité Frequence Valeur par défaut Description Description Channel name Unity Frequency Default value A_X* Accélération longitudinale Longitudinal acceleration 50Hz A_Y* Accélération latérale Lateral acceleration 50Hz Barrillet Volt Valeur de la position barrillet Barrel position elaborated value Brk_Fonct Info fonctions BRK...
- Page 24 Wintax : Channel list - 2 Nom du canal Unité Frequence Valeur par défaut Description Description Channel name Unity Frequency Default value Rapport_BV Rapport BV pour affichage Gear for dashboard data Regime Régime moteur Engine speed 20Hz Richesse Richesse moteur Lambda richness 20Hz RxBufDiag1BRK0...
- Page 25 Wintax : Channel list - Intensities Nom du canal Unité Valeur d'utilisation moyenne Description Description Channel name Unity Average using value I_AB Courant consommé : anti-brouillard Current consumption : antifog light 0,35 I_BALISE Courant consommé : cellule infrarouge Current consumption : infrared sensor I_CARTE Courant consommé...
- Page 26 Wintax : BRK output shutdown LOW OFF HI OFF The output is shutdown at this moment. The output has been shutdown previously in the data opened. A LOW OFF output correpond to a low amparage componant. A HI OFF output correpond to a hi amparage componant. * : chart only valid with the User_208R2_2019...
-
Page 27: Engine Synchronisation Diagnosis
Wintax : Engine synchronisation diagnosis LOW OFF HI OFF Diagnosis happening No Smot signal Diagnosis happened No Scam signal previously in the opening data. Signal noisy Cam wrong position Signal Smot recovered Engine synchronisation lost Damaged teeth on the target Missing teeth on the target Scam target error Scam target unphased...
Need help?
Do you have a question about the 208 R2 and is the answer not in the manual?
Questions and answers