Advertisement
Advertisement
Table of Contents
Related Manuals for PEUGEOT 208 R2
Summary of Contents for PEUGEOT 208 R2
- Page 1 208 R2 USER GUIDE Update of the 3 February 2014 1 / 21...
-
Page 2: Table Of Contents
SUMMARY ENGINE Page 3 Start Crank Oil Level Belts Page 4 TRANSMISSION BRAKE Page 6 Circuit bleeding Limiter Bedding-in Thickness WHEEL NUTS Page 8 FUEL LEVEL Page 9 Page 11 WINTAX4 SOFTWARE 2 / 21... -
Page 3: Engine
ENGINE START The first start of the engine must be done following this procedure: Master switch ON Power OFF Push the horn button Push the start button in the 5 following seconds and keep pushing Repeat this operation as long as the oil pressure is under 3.5 bars Then follow the process detailed below Every start in tempered condition must be done as defined below: Master switch ON... -
Page 4: Crank
If the engine does not start after 2 tries, do a crank procedure as detailed below: CRANK If you can’t start your engine after few tries, we recommend you to do the following procedure: Master switch ON Power OFF Push the horn button Push the start button in the 5 following seconds and keep pushing. -
Page 5: Transmission
TRANSMISSION DRIVESHAFTS BEDDIN-IN We recommend you to run in your driveshaft before the first use: Step 1 Car ready to run, on stands, engine running at 3000 rpm in 5th gear during 5 minutes, without playing with the steering wheel. Step 2 Same as step 1, in same time turn the steering wheel left and right by a half turn. -
Page 6: Brake
Do this procedure as detailed below: Front right and rear right callipers, outside bleeding screw Front right and rear right callipers, inside bleeding screw Front left and rear left callipers, outside bleeding screw Front left and rear left callipers, inside bleeding screw Then tight the bleeding screw: 18 N.m for cold calliper 14 N.m for hot calliper... -
Page 7: Limiter
Targets for pads bedding-in Distance (km) Pads temperature Front brake pressure At the end of bedding-in, drive 3 km at medium speed to cool down discs and pads. Then set you brake limiter to the initial setting. Case of discs and pads not bedding-in together When pads and discs have not been bedding-in in the same time, you must do a specific bedding-in to associate discs and pads. -
Page 8: Wheel Nuts
BRAKE PADS THICKNESS To avoid an excessive temperature of the brake system and to ensure a good and free travel, do not use pads with a thickness less than 10 mm. When you replace the brake pads, we recommend you first to clean the calliper pistons area first to avoid damaging the pistons. -
Page 9: Fuel Level
FUEL LEVEL There is no fuel gauge system to measure the fuel level in the tank. We remind you it is not allowed to add a gauge or modify the fuel tank foam. To know the fuel level, you must: Sum the fuel volumes add in the fuel tank since the last drain Sum the fuels consumptions displayed on the dashboard since the last drain... - Page 10 EXEMPLE 2 Fuel volume Consumption since the In the fuel tank In the Place Volume start of the rally – after the fuel added dashboard information consumption tank (litres) (litres) (litres) (litres) + 10 of Workshop reserve* 40 + 30 = –...
-
Page 11: Wintax4 Software
WINTAX PRESENTATION The 208 R2 is equipped with a data logging system which allows the control of the engine and chassis of the 208 R2. To be able to work with the data, you must: - buy the Ethernet cable, reference 3Z9S89529A... - Page 12 Then set the network connections Click on local network Click on « Internet Protocol version 4 (TCP/IPv4) » Set these Tick informations 12 / 21...
- Page 13 In some cases, you must deactivate the firewall to allow the connection with the car. DATA DOWNLOAD Please find the procedure to download the data: Step 1: Launch the WinTax4 software. Step 2: Click on « Acquisition » then « Acquisition Manager »...
- Page 14 Step 3: On the « WTX4AcquMan » window, click on Acquisition then « Setup » 14 / 21...
- Page 15 Step 4: Before every download, it is imperative to fill the following information then validate with the icon . Here is an example for a rally: Track: write the year, month*, the week then the 2013A_S03_MonteCarlo (* January = A, December= L). Session: write the day (1 day, 2 day….)
- Page 16 (the icon is green as there is a connection between the car and the computer). The 208 R2 ECU is named: « 208R2_XX », XX is the serial number of the ECU. In this case, there is no connection...
- Page 17 Step 6: The « TLap » window is now opened, select the runs you want to display and then click on "OK". Sélection des tours à Runs selected in télécharger blue DISPLAY THE DATA Step 1: Click on the icon or click on «...
- Page 18 Step 2: The Wtx4DataBrowser window is displayed. Click on the icon to select the data file. Standard location is C:\WinTAX4\Data Select the file Then select the runs you want to display 18 / 21...
- Page 19 MEANINGS OF THE VARIOUS ACQUISITION CHANNELS OF 208 R2 Barrillet Gear box barrel position BRK_Fonct BRK functions BRK_SW BRK switches DDU_Vbatt MPDU voltage Diag_Team Current team analog input diagnostic DiagAcqAna0 Current analog input diagnostic Distance Elapsed distance FlagBobCC Ignition coil short circuit flags...
- Page 20 I_VIRAGE Turns headlights current LEVEL Fuel level Lim_all Ignition limiter Lim_inj Injection limiter mbar Dynamic barometric pressure P_Frein_A_M Hand brake pressure P_FreinAR Rear brake pressure P_FreinAV Front brake pressure Motorized throttle sensor position Pedal sensor position Poil Motor oil pressure Rapport_BV Gear displayed Regime...
- Page 21 3, rue Marcel Dassault BP 68 78143 VELIZY Cedex www.peugeot-sport.com Technical support team 208 R2 Jean-François GRANDCLAUDON Technical support team manager Tél. : + 33 (0) 1 30 70 22 74 / + 33 (0)6 08 80 09 14 Email: jeanfrancois.grandclaudon@mpsa.com...
Need help?
Do you have a question about the 208 R2 and is the answer not in the manual?
Questions and answers