Related Manuals for Panasonic External Presentation unit 1728
Summary of Contents for Panasonic External Presentation unit 1728
- Page 1 Technical Description MEW00290 Revision 1 External Presentation unit 1728 Author: Jan Pettersson Date of issue: 2005-03-31 Date of rev: 2006-10-11...
- Page 2 This page has deliberately been left blank.
-
Page 3: Table Of Contents
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Table of contents Introduction________________________________ 3 Definitions / Explanations ____________________ 4 General description _________________________ 5 Ext. Presentation unit 1728 ___________________________ 5 3.1.1 SW mode 1728 - 1587__________________________ 5 3.1.2... - Page 4 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 This page has deliberately been left blank.
-
Page 5: Introduction
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Introduction This document describes the External Presentation unit 1728 (Informationstablå). The shorter expression EPU will also be used in this document. The 1728 unit can run in one of two SW modes:... -
Page 6: Definitions / Explanations
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Definitions / Explanations Definitions / explanations / abbreviations / etc. frequently used or not explained elsewhere in the document. External Presentation Unit C.i.e. -
Page 7: General Description
/ heat alarm presentation. One or more faults in the system will be presented as "General fault in system". Ext. Presentation unit 1728 Figure 1. The External Presentation Unit 1728 has a Swedish front. The enclosure is made of grey (RAL 7035) high impact ABS, with temperature resistance up to 85°... -
Page 8: Selective Alarm Presentation
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Selective alarm presentation Normally all fire alarms will be presented in the c.i.e:s, ext. FBP:s and Presentation units, etc. There are some possibilities to select which alarms that shall be presented in each unit. - Page 9 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Default in system EBL512 is: Control units (00, 29), i.e. all alarms from all c.i.e:s will be presented in all ext. Presentation units 1728.
-
Page 10: Led Indicators, Push Buttons, Etc
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 LED indicators, Push buttons, etc. The functions of the LEDs, push buttons, display and buzzer are described below. Ext. Presentation unit 1728 Figure 2. - Page 11 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Table of LED indicators: LED indicator Colour Indicating Fire (Brand) 2 x Red Blinking+ Fire alarm. (Also indicating pre- Buzzer warning, co-incidence and heavy smoke (interm.)
- Page 12 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Table of push buttons: Push button Colour Operation / function Alarms queued Black Used, when LED "Alarms queued" (L2) is turned on, (Flera larm) to scroll through the queued alarms.
-
Page 13: Sw Mode & Address Setting
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 SW mode & Address setting Each Ext. Presentation unit shall run in SW mode 1728 - 1587 or SW mode 1728 – 1582, i.e. it can be used as two different types of units. -
Page 14: Sw Mode Setting Via Jumper "J4
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 LANGUAGE SETTING! Change = Black Language: XXXXXXX Store = Yellow can be changed to one of the following languages: XXXXXXX - English... -
Page 15: Address Setting Mode Via The C.i.e
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 For an ext. Presentation unit with SW mode 1728 - 1582, the address can be set to 01-08. (Default is "01".) Scroll to the wanted address with the push button "P1" (black). - Page 16 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Power on / Restart / Reset via "JP1" "J4" ON? SW mode selected? SW mode setting Normal operation Address SW mode command from xxxx - 1587? c.i.e.
-
Page 17: User Definable Text Messages
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 User definable text messages The user definable text messages (alarm texts) are depending on which mode the unit is running in. In SW mode 1728 - 1587 In the c.i.e., each alarm point (zone –... -
Page 18: Commissioning A New Unit / Ssd Download
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Commissioning a new unit / SSD download The 1582 / 1587 board shall be mounted in the EBL512 c.i.e. and the fuse "F1" shall be removed. The cable (RS485 line) to the ext. - Page 19 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 8. After download of SSD to an ext. Presentation unit, there will be shown (very quickly): "SSD Download Memory OK" "SSD Download Memory Fault") After that it will restart, see chapter "Restart", page 18.
-
Page 20: Restart
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Restart The ext. Presentation unit will restart: • After the unit is powered up • If the jumper "JP1" is shunted momentarily •... -
Page 21: Fault Messages
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Fault messages Here follows a list of the fault messages that might be displayed in the ext. Presentation unit and in the c.i.e. respectively. -
Page 22: Ebl128 C.i.e
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 "FAULT: SSD, EPU xx, 1587 board x, CU xx" See chapter "Restart", page 18. 10.2.2 EBL128 c.i.e. "FAULT: No reply EPU x The contact with the ext. -
Page 23: Software (S/W)
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Software (S/W) The software is stored in a flash memory in each ext. Presentation unit. This software can be replaced / updated (i.e. downloaded via Win512 / Win128). -
Page 24: S/W Download
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 5 The ext. Presentation unit will restart, i.e. the buzzer will sound for approx. two seconds and the unit will return to normal operation. -
Page 25: Operation
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Operation In normal operation (quiescent condition) the LED "Operation" (L6) is turned on, the alphanumeric display is blank (back-light off) and the buttons are not possible to use. - Page 26 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Figure 3. Operation summary for the Ext. Presentation unit 1728. (Co-incidence alarm = 2-zone / address dependence.)
-
Page 27: Connections
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Connections The ext. Presentation unit is equipped with a plug-in terminal block (J1) for the cable connections. Up to 1.5 mm conductor area can be used. - Page 28 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Comments to the components: 1.5 A fuse (not replaceable, i.e. the whole p.c.b. has to be replaced). Terminal block for the ext. Presentation unit connections.
-
Page 29: Technical Data
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Technical data 14.1 Power supply Nominal voltage for the Ext. Presentation unit 1728 is 24 V DC. The number of Ext. Presentation units that can be power supplied from the c.i.e. - Page 30 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 The following table shows the current consumption for the unit in relation to the actual line voltage (min. and normal respectively): Unit...
-
Page 31: Revision History
Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728 Revision history Revision 1 In the whole document are elucidations and small corrections made, EBL128 info added and EBL512 info specified. - Page 32 Panasonic Electric Works Fire & Security Technology Europe AB MEW00290 Rev: 1 Technical Description External Presentation unit 1728...
- Page 33 This page has deliberately been left blank.
- Page 34 Panasonic Electric Works Fire & Security Technology Europe AB Citadellsvägen 23, SE-211 18 Malmö, Sweden Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99 info@mfstech.com • www.panasonic-fire-security.com...