Advanced wall mount hd video modulator.
2014 advanced model with also usb recording and play capabilities,
1080p input over both mpeg2 and mpeg4 modes, low latency encoding
and the newest mpeg4 h264 us tv standard mode (26 pages)
Page 2
Can be mixed with other HDTV signals such as Digital Cable or Over the Air Channels (depending on Frequencies available for you to use) Modular – Expandable – Reliable - 5 Year Warranty - Affordable VeCOAX Network Compact HDMI RF Modulator Manual...
Page 3
After the scan is complete, you can tune to channel 1.1, and the test pattern will be visible. By default, our unit is set to QAM (J.83B Cable) mode. This can be changed by referring to our INTERFACE CONFIGURATION GUIDE on Page 6. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 4
DEVICE LAYOUT 1) Network Port (Ethernet) 5) HDMI Input 2) GREEN Power Indicator Light 6) RST - Reset Button 3) BLUE On-Air Indicator Light 7) Power In (12V 1A DC) 4) RF Coax Connector VeCOAX Network Compact HDMI RF Modulator Manual...
Page 5
(J.83B) Mode with a Frequency of 783.000 MHz which is physical channel 122. Channel numbers are Major 1, Minor 1. The TV will pick up the channel on Cable channel 1.1 and display our PVI logo when no HDMI is connected.
Page 6
IP address of 192.168.0.136. 1. Connect your PC to the Network Port of the VeCOAX unit via Ethernet cable. 2. On your PC, in the Control Panel, open Network and Sharing Center (Network and Internet for Windows 8 and above) 3.
Page 7
NETWORK: Here you can change the IP address, subnet mask, and gateway for accessing the web interface. • UPDATE: Here you can apply firmware updates to your unit, if directed to do so by PVI support staff. • ABOUT: Here you can find the unit’s firmware version.
Page 8
• 1080P CONVERSION: If your TV Tuner is older and only supports 1080i video this will automatically downgrade any 1080P video to 1080i for compatibility. Auto is the default mode. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 9
MASK: You may need to change this one if your network is heavily managed, or if you are going through a switch. Otherwise, the default should work fine. • GATEWAY: Like your IP address, you will need to configure this to match your current network settings. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 10
Depending on your setup we recommend for you to use an active splitter or combiner with more than 6 units, 40+ TVs or using multiple splitters (each splitter will lower the DB level 5-10dbs depending on VeCOAX Network Compact HDMI RF Modulator Manual...
Page 11
• MPEG – MPEG 2 Layer II used in DVB-T EU Standard. • ACC - Advanced Audio Coding or MPEG-4. Used in some ATSC broadcasts and ISDBT format. Supported by Most TVs worldwide. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 12
If possible, test with a different TV with a different make/model. Use default settings on the unit. (To reset to default settings, press and hold the “RST” button for 15 seconds while the unit is powered on.) VeCOAX Network Compact HDMI RF Modulator Manual...
Page 13
Fixed EDID to 1080p. Audio setting issues can also cause full video dropouts. Check HDMI Audio Out settings on the source device. Set to Stereo PCM Linear or Dolby Digital 2 Channel (Uncompressed). VeCOAX Network Compact HDMI RF Modulator Manual...
Page 14
Check HDMI cable connection between source and unit. Disconnect HDMI source and reconnect it to establish a new HDMI handshake. Test with a different cable if possible. Test with a different source (e.g. DVD player) if possible. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 15
If using a converter box, set the STANDARD on the unit’s menu to match the type of converter box. (For Over-the-Air, set the unit to ATSC. For Cable, set the unit to J83B.) VeCOAX Network Compact HDMI RF Modulator Manual...
Page 16
Please see page 10 for more information. MORE THAN TWO UNITS ONLY PICKING UP A FEW CHANNELS AND NOT ALL? Ensure that each unit has its own Frequency, Major, Minor, and Channel Name. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 17
122) and stores the channel with the assigned Major/Minor you have set on the unit. WHAT IS THE DIFFERENCE BETWEEN FREQUENCY CHANNEL LISTED ON THE CHARTS VERSUS THE MAJOR MINOR CHANNEL NUMBER? VeCOAX Network Compact HDMI RF Modulator Manual...
Page 18
ASAP the following business day. Free phone tech support is available by calling +1 407 720 6101 ext #2, MON-FRI 9:30 AM – 5 PM US EST TIME. VeCOAX Network Compact HDMI RF Modulator Manual...
Page 19
SUGGESTED DEFAULT = 783000KHZ (783 MHZ) = frequency channel 122 6 MHz Apart Note: this is just the frequency the VeCOAX will use on the coax cable spectrum IT IS NOT the memory position number on the TV You can set ANY memory position number on the TV by setting the Major/Minor Number as you prefer.
Page 29
SUGGESTED DEFAULT = 473000kHz (473 MHz) = frequency channel 14 6 MHz Apart Note: this is just the frequency the VeCOAX will use on the coax cable IT IS NOT the memory position number on the TV You can set ANY memory position number on the TV by setting the Major/Minor Number as you prefer.
Page 30
Pro Video Instruments UHF band Channel ATSC FREQUENCY VeCOAX Network Compact HDMI RF Modulator Manual...
Page 31
Pro Video Instruments Channel ATSC FREQUENCY VeCOAX Network Compact HDMI RF Modulator Manual...
Page 32
Pro Video Instruments Channel ATSC FREQUENCY VeCOAX Network Compact HDMI RF Modulator Manual...
Page 35
Please download the DVB-T additional PDF for your country available on our Tech Support Website – pvisupport.com EUROPE/NEW ZEALAND = 8 MHz band AUSTRALIA = 7 MHz Band COLOMBIA = 6 MHz Band VeCOAX Network Compact HDMI RF Modulator Manual...
Need help?
Do you have a question about the VeCOAX and is the answer not in the manual?
Questions and answers