Sealey BC25635SR Instructions

Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Warning:
instruction explosive
manual risk

1. SAfETy

1.1. PersonAl PrecAutions
ensure that Health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment
9
ensure that there is another person with you especially within hearing range of your voice, or close enough to come to your aid
9
should a problem arise when working near a lead-acid battery.
remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit
9
current high enough to weld a ring or the like to metal, which may cause severe burns.
ensure that hands and clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and
9
contain long hair.
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
9
DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.
8
DO NOT drop any metal tool onto the battery as it may spark or short circuit the battery which could cause an explosion.
8
DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
8
1.2.

GenerAl sAfetY instructions

familiarise yourself with the application, limitations and potential hazards relating to this product. Also, refer to the vehicle
9
manufacturer`s handbook. if in AnY douBt consult An electriciAn.
ensure that the booster cables are in good order and condition before use. if in any doubt do not use the unit and contact an auto
9
electrician.
DO NOT dis-assemble the Booster cables for any reason. the booster cables must be checked only by qualified service personnel.
8
only use recommended attachments and parts. to use unapproved items may be dangerous and will invalidate your warranty.
8
WARNING! check that both vehicle batteries are the same voltage.
‰
ensure that vehicles are not touching before attempting to use these leads.
9
Keep tools and other items away from the engine, and ensure that you can see the battery and the working parts of the engine
9
clearly.
Keep children and unauthorised persons away from the work area.
9
ensure that the jump leads are not tangled and are clear of moving or hot engine parts.
9
DO NOT allow the clamps to touch each other or to make contact with the vehicle bodywork, as this may result in arcing.
8
DO NOT cross connect the power leads to the battery. ensure positive is to positive and negative is to negative.
8
DO NOT pull the cables or clamps from the battery terminals.
8
DO NOT operate in the vicinity of flammable liquids or gases.
8
DO NOT try to jump start a frozen battery.
8
DO NOT use or store the booster cables in damp or wet locations.
8
DO NOT use this product to perform a task for which it is not designed.
8
the cables may become hot with excessive use. if so, allow a few minutes for them to cool before attempting to re-use.
9
if the surge protection unit receives a sharp knock or blow, the unit must be checked by a qualified service agent before next use
9
When not in use, store the booster cables carefully, in the case provided, in a safe, dry, childproof location.
9
WARNING! modern vehicles contain extensive electronic systems.
‰
You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of equipment on
each vehicle.

2. INTRODuCTION

the Booster Cables consist of PVC sheathed copper coated aluminium cables which give maximum power transfer yet remain flexible and
resistant to oil, grease and most acids. insulated heavy-duty clamps reduce the heating effect of power transfer. the unit features an led
display unit which shows the battery voltage and includes a reverse polarity indicator and alarm. in line surge protector helps to prevent
electrical spikes occurring. Additional features include alternator charge check and battery condition check and is supplied in a carry case.
© Jack sealey limited
instructions for
BOOSTER CABLES 25mm
model no:
Wear
Wear eye
Protectve
Protection
Gloves
Original Language Version
BC25635SR
Warning: Warning:
electricity corrosive
2
X3.5m CCA 600AmP
Bc25635sr | issue 1 26/04/16