Related Manuals for Curtis WB2A10
Summary of Contents for Curtis WB2A10
- Page 1 USER GUIDE 2 Gallon Water Boiler READ AND SAVE THESE INSTRUCTIONS NOTICE TO INSTALLER: Please leave this booklet with the machine.
-
Page 2: Table Of Contents
..............................CI16 ...................................................................................................ES83 ......................................................................................Contact Information Wilbur Curtis Co., Inc. 6913 Acco Street | Montebello, CA 90640 US Phone: 323-837-2300 | Toll Free: 800-421-6150 Email: csrassistance@wilburcurtis.com | Web: www.wilburcurtis.com . - 4:00 . PT Email: techsupport@wilburcurtis.com... -
Page 3: Fs39
KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS39 Key Features • • 2.0 Gallon - domestic 1 PH 120 V 13.3 A 1 X 1600 W 2W + G 1600 W 50/60 Hz [18.9 l/hr] 2.0 Gallon - Canada 1 PH 120 V 12.5 A 1 X 1450 W 2W + G 1500 W... -
Page 4: Is2
INSTRUCTIONS could result in personal injury or void the warranty. • This appliance is designed for commercial use. Any service other than cleaning and preventive maintenance should be performed by an authorized Wilbur Curtis service technician. • serviceable parts inside. - Page 5 IMPORTANT SAFEGUARDS CE Requirements • This appliance must be installed in locations where it can be overseen by trained personnel. • • This appliance is not suitable for outdoor use. • • • This appliance must not be cleaned by water jet. •...
-
Page 6: Ii20
INSTALLATION INSTRUCTIONS II20 WARNING: WARNING: properly grounded. NOTICE: SPECIFICATIONS section. IMPORTANT: Installation Instructions Installation Requirements • A secure surface capable of supporting the weight of the appliance. • For units without an attached cord set: Appropriately sized, UL listed, grounding type power cable to meet enough •... -
Page 7: Ii21
INSTALLATION INSTRUCTIONS II21 Installation NOTICE: Failure to follow the First Time Power Up Instructions may result in damage to the unit. Leveling Position the water boiler on the countertop. Level it left to right and front to back by turning the bottom of the legs. - Page 8 INSTALLATION INSTRUCTIONS II21 First Time Power Up Instructions (cont.) For units equipped with a power connector on the back Back of unit panel, connect a C20 IEC power cord (not supplied) compatible with the electrical outlet installed in the C20 connector (Some versions) Make sure that the power switch is off, then connect the power plug to the appropriate type of electrical outlet.
- Page 9 INSTALLATION INSTRUCTIONS II21 13 Remove the top cover and rotate the shaft on the Thermostat thermostat completely clockwise. IMPORTANT: When operating the unit at higher elevations, reduce the factory set operating temperature by 2°F/1°C for each 1000 ft./300 m of elevation above 4000 ft./1200 m.
-
Page 10: Ci16
CLEANING INSTRUCTIONS CI16 WARNING: HOT SURFACES - To avoid injury, allow the unit to cool 30 minutes before cleaning. NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives. USE OF THESE PRODUCTS WILL VOID THE WARRANTY. - Page 11 ROUGH-IN DRAWINGS RD45 14.86 in [37.7 cm] 13.54 in [34.4 cm] 9.27 in [23.6 cm] 3.47 in [8.8 cm] 23.85 in 20.13 in [60.6 cm] [51.1 cm] 15.22 in WATER SUPPLY [38.7 cm] CONNECTION 14.45 in [36.7 cm] CLEARANCE 8.00 in 13.35 in [20.3 cm] [33.9 cm]...
- Page 12 ILLUSTRATED PARTS/RECOMMENDED PARTS IP73 WB2A10/20/30 - Main Chassis - Exploded View Water tank assembly, see section IP74 WB2, ILLUSTRATED PARTS/RECOMMENDED PARTS 080219C...
- Page 13 SWITCH, TOGGLE NON-LIT SPST 15A WC-102 1,2 125/6A 250VAC RESISTIVE SWITCH, TOGGLE NON-LIT DPST 25A WC-103 3,4 125/250VAC RESISTIVE 1 WB2A10, 2 WB2A20, 3 WB2A30 (older units), 4 WB2A30 (newer units) Recommended Parts to Stock ITEM # PART # DESCRIPTION ITEM #...
- Page 14 WC-37266* KIT, FITTING TANK OVERFLOW KIT,ELEMENT, HEATING 1.6KW120V W/ JAM NUT & WC-904-04 1 WC-75333 1 11A** TANK, ASSY WB2A10 SILICONE O-RING WC-75333-30 2 11B** TANK, ASSY W/WC-906 2000W HEATING ELEMENT KIT, ELEMENT, HEATING 2KW 220V W/ JAM NUT &...
-
Page 15: Es83
ELECTRICAL SCHEMATICS ES83 WB2A10, WB2A20 WB2, ELECTRICAL SCHEMATIC 122719D... - Page 16 ELECTRICAL SCHEMATICS ES83 WB2A30 WB2, ELECTRICAL SCHEMATIC 122719D...
- Page 17 TROUBLESHOOTING GUIDE TG22 WARNING: Electric Shock Hazard - Scald and Burn Hazard - NOTICE: Troubleshooting Guidelines • • ELECTRICAL SCHEMATIC. • Valve Test Procedure in either direction No Power Water Tank Does Not Fill IMPORTANT:...
- Page 18 TROUBLESHOOTING GUIDE TG22...
- Page 19 TROUBLESHOOTING GUIDE TG31 Water Not Hot Enough Water Does Not Heat At All Tank Does Not Fill • If the water heats, but is not hot enough, see Water Not Hot Enough • • Checking the heating element: ELECTRICAL SCHEMATIC Water Heats More Slowly Than Usual Water Too Hot (Boiling or Excessive Steaming) IMPORTANT:...
- Page 20 Return Merchandise Authorization (RMA): All returned equipment must be properly re-packaged in the original carton and received by Curtis within 45 days following the issuance of a RMA. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).
Need help?
Do you have a question about the WB2A10 and is the answer not in the manual?
Questions and answers