Advertisement
Quick Links
Universal Groomer Drive MVP Kit
Reelmaster
or 7-inch Reel
Model No. 133-0150
Model No. 133-0151
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
18-inch, 22-inch, or 27-inch Cutting Units with 5-inch
Description
No parts required
No parts required
No parts required
Extended splined insert (right-hand
threads)
Extended splined insert (left-hand
threads)
Flange locknut (3/8 inch)—Model
133-0151 only
Weight bracket
Hex-socket, button-head bolt (3/8 x 3/4
inch)
Right (yellow) reel adapter
Left (green) reel adapter
Groomer drive box
Hex-socket-head bolt
Pivot hub
O-ring
Idler assembly
Bearing shield
Adjuster collar
Stub-shaft assembly
Flange nut (3/4 inch)
Flange locknut (3/8 inch)—Model
133-0150 only
Jam locknut (3/8 inch)—Model 133-0151
only
Left HOC bracket assembly
Right HOC bracket assembly
Adjuster pin
Cotter pin
Flange locknut (3/8 with 5/8 hex)
Cap
Register at www.Toro.com.
Form No. 3421-332 Rev C
Installation Instructions
Qty.
–
Prepare the machine.
–
Gather the tools required for setup.
Determine where on the cutting unit to
–
install the groomer.
1
1
Prepare the cutting unit.
2
1
2
Install the groomer drive box and weight.
1
1
1
2
1
1
1
2
1
Install the idler assembly.
1
1
2
2
1
1
Install the HOC bracket assemblies and
2
the front roller.
2
2
Install the groomer drive cap (For
1
universal groomer assemblies with no
rear roller brush kit installed only).
Original Instructions (EN)
All Rights Reserved *3421-332* C
Printed in the USA
Use
Advertisement
Related Manuals for Toro 133-0150
Summary of Contents for Toro 133-0150
- Page 1 Universal Groomer Drive MVP Kit Reelmaster ® 18-inch, 22-inch, or 27-inch Cutting Units with 5-inch or 7-inch Reel Model No. 133-0150 Model No. 133-0151 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped.
-
Page 2: Preparing The Machine
Shaft clamp Install the angled fitting (for Reelmaster Hydraulic fitting—45° (Part No. 3550 and 3555 machines, #1 front, 340–101; sold separately) center cutting location and kit Model 133-0150). Preparing the Machine Determining the Setup No Parts Required No Parts Required Procedure Procedure Park the machine on a level surface. - Page 3 tool (Part No. TOR4112 for the 5-inch reel and Part No. TOR4074 for the 7-inch reel). Refer Figure Important: The splined insert on the left Preparing the Cutting Unit side of the cutting unit has left-hand threads. The splined insert on the right side of the cutting unit has right-hand threads.
- Page 4 Installing the Weight Bracket and the Groomer Drive Box Parts needed for this procedure: Weight bracket Hex-socket, button-head bolt (3/8 x 3/4 inch) g037064 Figure 4 Right (yellow) reel adapter Left (green) reel adapter 1. Flange-head bolts 2. Support rod Groomer drive box Install the 2 existing flange-head bolts from the inside of the cutting unit, and secure...
- Page 5 Note: Use the yellow adapter on the right side of the machine; use the green adapter on the left side of the machine. Discard the unused reel adapter included in the kit. Note: Restrain the groomer shaft with the adapter wrench tool (Part No. 137-0921, sold separately) on the wrench flats on the back side of the groomer drive box (Figure...
- Page 6 O-ring Idler assembly Bearing shield Adjuster collar Stub-shaft assembly Flange nut (3/4 inch) Flange locknut (3/8 inch)—Model 133-0150 only Jam locknut (3/8 inch)—Model 133-0151 only Procedure Assemble the parts that make up the idler assembly as shown in Figure 9. Torque the flange nut (3/4 inch) to 37 to 45 N∙m (27 to 33...
- Page 7 Installing the HOC Bracket Assemblies and the Front Roller Parts needed for this procedure: Left HOC bracket assembly g232400 Figure 11 Right HOC bracket assembly Adjuster pin 1. Adjuster pin 3. Cotter pin 2. Adjuster-arm rod 4. Groomer drive box Cotter pin Flange locknut (3/8 with 5/8 hex) On the idler assembly side, align the...
- Page 8 Install the cap as shown in Figure g242099 Figure 14 1. Cap 2. Apply Green Loctite 609® If you are installing the groomer at the left side of the machine, perform the following (Figure 15): Remove the O-ring from the clutch knob. Remove the shear pin that secures the clutch knob to the actuator shaft.
- Page 9 Installing the Groomer Assembly and Optional Broomer Kit Groomer and Broomer Kits Come Separately Parts needed for this procedure: Bolt (1/4 x 1-1/2 inches) Jam nut Shaft clamp g240752 Figure 16 Installing the Groomer Kit 1. Drive-stub shaft 4. Shaft clamp (4) 2.
- Page 10 g032402 Figure 19 1. Brush 2. Blade Loosely wrap the straps, as shown in Figure 17, around the groomer reel shaft and brushes, inserting the straps in the grooves in the brushes Figure Position the straps on the brushes using the following table: Reel Size Strap Spacing...
- Page 11 Procedure Important: For Reelmaster 3550 and 3555 machines—#1 front, center cutting location and kit model 133-0150 only; order 45° hydraulic fitting (Part No. 340–101) and follow the procedure below. Remove the hydraulic hose from the hydraulic fitting on the motor.
-
Page 12: Operation
Operation • The type of grass • The overall management program (i.e., irrigation, fertilizing, spraying, coring, overseeding, etc.) Introduction • Traffic Grooming is performed in the turf canopy above the • Stress periods (i.e., high temperatures, high soil level. Grooming promotes vertical growth of grass humidity, unusually high traffic) plants, reduces grain, and severs stolons, producing a denser turf. - Page 13 Adjusting the Groomer Repeat step at the opposite end of the groomer, then check the setting on the first side Height of groomer. The height setting on both ends of the groomer should be identical. Adjust the height as DANGER required.
- Page 14 Height-of-Cut (HOC) and Height-of-Groom (HOG) Recommended Range Height-of-Cut Height-of-Cut Number of Recommended HOG = HOC - Recommended HOG = HOC - (mm) (inch) Rear Roller Groomer Engagement Groomer Engagement Spacers (mm) (inch) 0.250 3.1 to 6.3 0.125 to 0.250 0.375 4.7 to 9.5 0.187 to 0.375 0.375...
-
Page 15: Maintenance
Testing the Groomer Maintenance Performance DANGER Important: Improper or over-aggressive use of Contact with the reels or other moving parts the grooming reel (i.e., too deep or too frequent can result in personal injury. grooming) may cause unnecessary stress on the turf, leading to severe damage. - Page 16 If you have any issues removing the 5-inch reels or 90 cc for 7-inch reels. groomer drive box, refer to your traction unit Service Manual or contact your authorized Toro distributor. Remove the cap from the groomer. Remove the clamp bolts connecting the groomer...
- Page 17 Cleaning the Grooming Reel Service Interval: After each use Clean off the grooming reel after using it by spraying it with water. Do not direct the water stream directly at the groomer bearing seals. Do not permit the grooming reel to stand in water so that the components rust.
- Page 18 Restraining the Reel WARNING The cutting reel blades are sharp and capable of amputating hands and feet. • Keep your hands and feet outside of the reel. • Ensure that the reel is restrained before servicing it. Restraining the Reel for Removing Threaded Inserts Loosen the shield-bolt on the left side of the g280383...
- Page 19 Restraining the Reel for Installing Threaded Inserts Insert a long-handled pry bar (recommended 3/8" x 12" with screwdriver handle) through the front of the cutting reel, closest to the side of the cutting unit that you will be torquing (Figure 30).
- Page 20 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.