Table of Contents
Advertisement
Table 5-3
Computer Setup—Configuration (for advanced users) (continued)
Option
Num Lock State at
Power-On
S4/S5 Wake on LAN
Device Options
Thermal
UEFI HII Configuration
Computer Setup—Boot Options
NOTE:
Support for specific Computer Setup options can vary depending on the hardware configuration.
Table 5-4
Computer Setup—Boot Options
Option
POST Hotkey Delay (sec)
USB Boot
Network Boot
Network Boot Protocol
Legacy Support
Secure Boot
Platform Key
Pending Action
UEFI Boot Order
44
Chapter 5 Computer Setup (F10) Utility
Heading
Let you set the Num Lock state after POST. Default is On.
Lets you control whether the computer wakes from S4 (hibernation) or S5 (soft off) if a magic packet is
received by the NIC. Default is Disabled.
Allows you to set:
●
Multi-Processor (enable/disable). Default is enabled.
Hyper-Threading (enable/disable). Default is enabled.
●
●
NIC PXE Option ROM Download (enable/disable). Default is enabled.
Displays current CPU fan speed in rpm.
Provides configuration of device-supported UEFI HII (Human Interface Infrastructure).
Heading
Setting to a non-zero value adds a delay during POST. This option can be necessary for certain add-in
peripherals that respond slowly or violate specifications. Default is 0.
Lets you enable booting from a USB device. Default is Enabled.
Lets you enable the computer's ability to boot from an operating system installed on a network server.
Default is Disabled.
Lets you select the network boot protocol. When IPV4+IPV6 is selected, BIOS uses IPV4 first. Default is
IPv4+IPv6(UEFI).
When Legacy Support is enabled, BIOS loads the Compatibility Support Module (CSM) to support legacy
operating systems. When Legacy Support is disabled, BIOS boots in UEFI Mode without CSM. Default is
Disabled.
Enable Secure Boot to block malware attacks, virus infections, and the use of non-trusted hardware or
bootable CDs or DVDs that can harm the computer. You can also disable Secure Boot to use trusted but
unrecognized hardware (such as older video cards) or to boot from an unrecognized recovery disc. Default
is Enabled.
The platform key verifies kernels during system start up, allowing you to use alternative operating
systems. Default is Enrolled-MSFT.
Default is None.
Specifies the order in which UEFI boot sources (such as a internal hard drive, USB hard drive, USB optical
drive, internal optical drive, or network adapter) are checked for a bootable operating system image.
Default is OS Boot Manager.
Use the Up and Down arrow keys to select a device. Press
list. If the device is marked with !, the device is disabled.
IMPORTANT:
UEFI boot sources always have precedence over legacy boot sources.
Shortcut to Temporarily Override Boot Order
F5
or
F6
to move the device up or down in the
- Quick Links:
- Preparation for Disassembly
- Display
- Memory
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the 200 G4 22 and is the answer not in the manual?
Questions and answers
MY AIO SCREEN BROKE AND I'M NOT ABLE TO PROJECT TO AN EXTERNAL DISPLAY VIA HDMI
The HP 200 G4 22 All-in-One does not have explicit instructions for HDMI output in the provided context. However, you can try the following steps:
1. Connect an external monitor to the HDMI port of the HP 200 G4 22 AIO.
2. Ensure the external monitor is powered on and set to the correct HDMI input.
3. If the screen remains blank, try using a different HDMI cable or monitor.
4. Restart the computer and see if the external display is detected automatically.
5. If the external display does not show output, try pressing Windows + P and selecting Duplicate or Extend using the keyboard.
6. If the screen is still blank, boot into Safe Mode or use Last Known Configuration as described in the troubleshooting steps.
If the PC does not support HDMI output, you may need to use a USB-to-HDMI adapter.
This answer is automatically generated