Download Print this page
Sealey SDH20.V4 Instructions

Sealey SDH20.V4 Instructions

20ltr

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Indoor use only
instructions
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
If the dehumidifier is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
GENERAL SAFETY
1.2.
Check that the dehumidifier is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
9
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
DO NOT stand or place any object within10cm from the front of the unit, 40cm from the rear and sides of the unit, and 40cm above
8
the unit.
DO NOT obstruct the air intakes or outlets of the dehumidifier, and do not cover with washed clothes.
8
DO NOT get wet.
8
DO NOT place any object into the outlets - the unit has a fan running at high speed, contact with this will cause injury.
8
DO NOT operate the dehumidifier when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT switch the dehumidifier off by disconnecting it from the mains. ALWAYS switch to the "OFF" position first.
8
DO NOT remove the float lever from the water collection tank.
8
DO NOT connect or disconnect the plug from the mains with wet hands.
8
DO NOT use an extension lead.
8
Unplug before moving.
9
Place on flat level ground which can hold dehumidifier and full water tank weight
9
Always discard the water from the collection tank, DO NOT use it for any other purpose.
9
To prevent water from freezing, do not use the dehumidifier at ambient temperatures below 0°C.
9
DO NOT use the dehumidifier outside.
8
When using continuous draining, make sure that the drain hose is positioned correctly.
9
Ensure that heating appliances are not exposed to the flow of air from the dehumidifier.
9
Before attempting to move the dehumidifier, empty the contents of the collection tank. Use top carrying handle when moving unit.
9
Switch off and disconnect it from the mains before cleaning or other maintenance work.
9
Ensure that the dehumidifier is correctly turned off when not in use, and stored in a safe, dry area, out of reach of children.
9
© Jack Sealey Limited
INSTRUCTIONS FOR
DEHUMIDIFIER 20LTR
SDH20.V4
MODEL NO:
Original Language Version
Recommended fuse rating
3 Amp
SDH20.V4 | Issue 1 23/09/16

Advertisement

loading

Summary of Contents for Sealey SDH20.V4

  • Page 1 SDH20.V4 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Check humidity to be adjusted is within range: 30% RH - 80% RH. 4.3.5. When the LED screen indicates “CO” this means continuous dehumidification. 4.3.6. When the set humidity is reached, the compressor will stop working, and the fan will stop for some time. Original Language Version SDH20.V4 | Issue 1 23/09/16 © Jack Sealey Limited...
  • Page 3 Remove water plug in the back cover and insert the water pipe into the water outlet. 4.10.3. Place the other end into a floor drain. 4.10.4. If the water hose is not being used, remove the water pipe and replace the water outlet plug. 4.10.5. Whether the water outlet hose is used or not the water tank must be in position otherwise the dehumidifier will not operate. Original Language Version SDH20.V4 | Issue 1 23/09/16 © Jack Sealey Limited...
  • Page 4 - Check if surface it is placed on is smooth Power light is on: - humidity sensor and/or temperature sensor broken or loose - contact Sealey stockist Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.