Sealey PWH599 Instructions

6. MEANING OF MARKINGS
Meaning of the markings on the filter:
4 / 9 - 13
Light state scale no.
Lightest dark state scale no.
Darkest state scale no.
Manufacturers identification.
Optical class.
Diffusion of light class.
Variation in luminence transmittance class.
Number of the applied standard.
Meaning of the markings on the helmet: Jack Sealey Ltd. = manufacturers identification
EN 175
S
7. PROBLEM SOLVING
s DANGER! If, at any time, the face plate in the cartridge FAILS to darken when exposed to a welding spark, DO NOT USE. Remove cartridge and
s
return to your dealer for checking. Continued use of the product with auto darkening feature NOT FUNCTIONING may DAMAGE YOUR EYES and
CAUSE BLINDNESS. Use of malfunctioning product will invalidate the warranty, and any right of claim on any insurance policy.
IRREGULAR DARKENING The headband may have been unevenly set on the two sides of the helmet Readjust the distance of the shade
OR DIMMING. (unequal distances from the eyes to the shade cartridge).
SHADE CARTRIDGE DOES The sensors are soiled or obstructed.
NOT DARKEN OR FLICKERS. Front cover lens oiled or damaged.
Welding current too low.
POOR VISION Operative lenses and/or shade cartridge soiled.
Insufficient ambient light.
Shade level incorrectly set.
SLOW RESPONSE Operating temperature too low
WELDING HELMET SLIPS Headband adjustments incorrect.
8. SPARE PARTS - VERSION 2
REF. PART NO. DESCRIPTION
IMPORTANT:
WARRANTY:
INFORMATION:
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Sole UK Distributor
Sealey Group,
Jack Sealey Ltd. 1 / 3 / 2
= number of the applied standard
= symbol of the robustness (Increased robustness)
cartridge.
Clean
Clean or replace
Adjust weld amps
Check, clean or replace
Adjust light
Refer to Shade Guide for setting
Do not use at temperatures below -5
Refer to section 4.
fig 6
01284 757500
Web address: www.sealey.co.uk
01284 703534
E-mail: sales@sealey.co.uk
/ 379
Thank you for purchasing a Sealey Power Product. Manufactured to a high standard this product
will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR
PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! THIS HELMET IS NOT SUITABLE FOR USE WITH LASER OR GAS-WELDING.
p
p
genuine parts only. Non authorised parts may be dangerous and will invalidate the
warranty.
C (23 F) .
0 0
WARNING! DO NOT use the helmet if damaged or you suspect it may be faulty. (Contact Service Agent).
p
p
DANGER! If, at any time, the face plate in the cartridge FAILS to darken when exposed to a welding spark, DO NOT USE.
s
s
Remove cartridge and return to your dealer for checking. Continued use of the product knowing that the auto darkening feature
is NOT FUNCTIONING may DAMAGE YOUR EYES and CAUSE BLINDNESS. Continued use of the helmet which is not
functioning will invalidate the warranty and could prohibit a successful claim on any insurance company.
2. INTRODUCTION
High quality variable shade 9-13 lens which does not deteriorate with age or usage, manufactured and tested to EN379:2003 . Fully
automatic, switches from light to dark on striking arc. Fitted with solar power panel, no batteries required. Features sensitivity switch and
delay speed switch control for switching dark to light, preventing arc eye when welding at high power, whilst still providing fast switching for
tack welding. Deluxe contoured helmet design approved to EN175:1997 gives full neck protection and protects lens from scratching
when helmet is laid down. Comfortable headband and non slip quick release ratchet mechanism. Suitable for MIG and arc welding. (Not
suitable for use with laser or gas-welding).
3. SPECIFICATION
AUTOMATIC WELDING HELMET
Use
NOT
(such as, but not limited to)
l
l
PWH599
Version 2