Related Manuals for Zanussi ZDF36001WA
Summary of Contents for Zanussi ZDF36001WA
- Page 1 User Manual GETTING STARTED? EASY. ZDF36001XA ZDF36001WA EN User Manual Dishwasher...
-
Page 2: Safety Information
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. -
Page 3: The Appliance
If the supply cord is damaged, it must be replaced by the • manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends • pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. - Page 4 WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
-
Page 5: Control Panel
CONTROL PANEL On/off button Delay button Display Programme buttons Indicators INDICATORS Indicator Description Salt indicator. It is on when the salt container needs refilling. Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. XtraDry indicator. PROGRAMMES The order of the programmes in the table may not reflect their sequence on the control panel. -
Page 6: Programme Selection Mode
Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Prewash 0.935 10.5 Crockery and • Wash 50 °C cutlery • Rinses • • Prewash 46-170 0.7 - 1.7 8 - 15 Crockery, cut- •... -
Page 7: Deactivating The Rinse Aid Empty Notification
1. Press To CANCEL, press and hold until the appliance is in programme selection mode. • The indicators are off. • The indicator still flashes. USER MODE • The display shows the current setting: e.g. User mode allows to change the following settings: = level 5. -
Page 8: Before First Use
– = rinse aid empty notification While the drying phase operates, the deactivated. device opens the appliance door. The door is then kept ajar. 2. Press to change the setting. 3. Press on/off to confirm the setting. By default, AirDry is activated with all programmes When rinse aid chamber is empty, the excluding (if applicable), but it is possible to... -
Page 9: Daily Use
ADDING SALT Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID The rinse aid helps to dry the dishes without streaks and stains. -
Page 10: Adding Multi-Tablets
ADDING MULTI-TABLETS • Adjust the water softener to the lowest level. THE AUTO OFF FUNCTION ACTIVATING XTRADRY This function decreases energy consumption by Make sure the appliance is in programme selection deactivating automatically the appliance when it is mode. not operating. To activate XtraDry: The function comes into operation: 1. -
Page 11: End Of The Programme
END OF THE PROGRAMME closing the door, the appliance continues from the point of interruption. When the programme is complete, the display shows: 0:00. If the door is opened during the drying • Press on/off or wait 5 minutes for the Auto OFF phase, before AirDry automatically function to automatically deactivate the opens it, the programme ends after 30... -
Page 12: Care And Cleaning
LOADING THE BASKETS • The filters are clean and correctly installed. • The cap of the salt container is tight. • Use the appliance to wash dishwasher-safe • The spray arms are not clogged. items only. • There is enough salt and rinse aid (unless you •... -
Page 13: Cleaning The Lower Spray Arm
• Reassemble the filters (A) and (B). • Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE LOWER SPRAY ARM We recommend to clean the lower spray arm regularly to prevent soil from clogging the holes. -
Page 14: External Cleaning
EXTERNAL CLEANING dishwashers at least once every two months. Carefully follow the instructions on the • Clean the appliance with a moist soft cloth. packaging of the product. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning •... -
Page 15: The Washing And Drying Results Are Not Satisfactory
Problem and alarm code Possible cause and solution The appliance stops and starts • It is normal. It provides optimal cleaning results and energy sav- more times during operation. ings. The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. - Page 16 Problem Possible cause and solution Poor drying results. • Tableware was left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not suffi- cient. Set the rinse aid dispenser to a higher level. •...
-
Page 17: Product Information Sheet
PRODUCT INFORMATION SHEET Trade Mark Zanussi Model ZDF36001XA 911516389 ZDF36001WA 911516390 Rated capacity (standard place settings) Energy efficiency class Energy consumption in kWh per year, based on 280 standard cleaning cycles using cold water fill and the consumption of the low power modes. The actual energy consumption will de- pend on how the appliance is used. -
Page 18: Additional Technical Information
Programme time of standard cleaning cycle (min) Duration of the left-on mode (min) Sound power level (db(A) re 1pW) Built in appliance Y/N ADDITIONAL TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 600 / 850 / 625 Voltage (V) 220 - 240 Electrical connection Frequency (Hz) - Page 20 WWW.ZANUSSI.COM/SHOP...