Advertisement
2. APPLICATION & SPECIFICATION
Compact and portable power planer/thicknesser with heavy-duty cast base
for accurate and smooth operation. Accurate fence tilts between 45° and
90°. Fitted with two blades capable of handling timber up to 200mm wide.
Easy conversion from planer to thicknesser. Thicknesser fitted with feed
rollers. No-volt release switch prevents uncontrolled re-start after power
interruption.
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1250W, 230V 50Hz.
Maximum Thicknessing Capacity . . . . . . . . . . . . . . . . . . . . .120mm
Maximum Cut (Width x Depth) . . . . . . . . . . . . . . . . . . . . .200 x 2mm
Thicknesser Feed Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . .7mtr/min
Cutter-head Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8000rpm
Fence Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45-90°
Working Table Size . . . . . . . . . . . . . . . . . . . . . . . . . . .737 x 210mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29kg
3. ASSEMBLY
3.1
ASSEMBLY
! WARNING! DO NOT plug the planer into the mains power
supply until completely assembled.
The machine is shipped nearly complete in one carton. Additional
parts which need to be fastened to machine should be located and
accounted for before assembling. (fig. 1).
A.
Planer and Thicknesser
B.
Angle fence
C.
4mm Hex wrench
D.
Handle assembly
E.
Hex bolt
F.
5mm lock washer
G.
5mm flat washer
H.
Dust chute
3.2
SETTING ANGLE FENCE (fig. 2)
3.2.1
Insert screw into the slot (A), then locate the fence on screw
(D). Securely tighten screw (A) first, then screw (D).
Angle adjustment is made by loosening knob (C) and
tilting fence to the desired angle using scale (B). Re-tighten
knob (C) fig. 2.
3.3
SETTING SAFETY GUARD (fig. 3)
3.3.1
To adjust the height of the guard, loosen knob A, raise
or lower the guard (B), until it is in firm sliding contact with the
workpiece. Tighten knob A.
3.3.2
After adjusting the guard height it can be adjusted sideways
to set the required stock width for jointing. (As in Fig.4)
Note! Make sure that the switch is in off position before adjusting
the cutting depth, replacing or adjusting blades. Make sure the blade
screws are securely tightened.
4. CHIP EXTRACTION
4.1
PLANING
4.1.1
Set the thicknessing table to the
lowest position.
4.1.4
Push the chute into position.
FIG. 1
H
FIG. 2
A
FIG. 3
A
FIG. 4
4.1.2
Insert the dust chute underneath
the planing work table.
4.1.5
The chute should be positioned to
allow both the keys to align with
the cut-outs on the table
G
F
D
C
E
B
B
4.1.3
4.1.6
A
B
C
D
Pull the keys on either side of the
chute and align the chute with the
work table.
Insert the keys into the cut-outs,
locking the chute into place.
SM1311 - 1 - 150506
Advertisement
