Related Manuals for Hunter Douglas Paramount
Summary of Contents for Hunter Douglas Paramount
- Page 1 Installation Operation Care • • Vertical Blind Collection Paramount , PermAlign , and PermaTrak ® ® ® Headrail Systems...
-
Page 2: Table Of Contents
Child Safety: Warning ..................17 Cord Loop Blinds................. 17 Questions? Call the Hunter Douglas Customer Information Center at 1-888-501-8364. © 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners. -
Page 3: Getting Started
GETTING STARTED Product View Outside Mount Adjustable Bracket Inside Mount Mounting Clip Optional PermAssure ® Safety Wand Control System Headrail Standard PermaTilt ® Wand Control System Vanes Optional Cord and Chain Control System... -
Page 4: Tools And Fasteners Needed
GETTING STARTED Thank you for purchasing Hunter Douglas Vertical Blinds. With proper installation, operation, and care, your new blind will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. -
Page 5: Installation
INSTALLATION Installation Overview Blind Brackets Width Required Your order will include installation brackets specific to ■ 15" – 48" your blind. The number of installation brackets required " – 72" varies with headrail width, as shown in the table. " – 96" "... -
Page 6: Valance Assembly
INSTALLATION Valance Assembly Please refer to the section below for your valance type. Proceed to “Mount the Installation Brackets — Inside Mount” on page 7 or “Mount the Installation Brackets — Outside Mount” on page 9 based on the mounting option ordered. Dust Cover Valance Assembly Single-tiered Closed Corner Cut a fabric insert for the valance and each valance return 1"... - Page 7 INSTALLATION Single-tiered open Corner (Fabric only) Cut a fabric insert long enough to wrap ■ Valance around the corner and over the entire Fabric Return return plus at least 1" excess at Insert each end. Attach the corner clip and valance ■...
- Page 8 INSTALLATION Single-tiered Round Corner Fabric Valance Install the round valance corners onto each end of the ■ Insert Return valance. Install the valance returns onto each end of the round ■ valance corners. Valance Cut the fabric insert 4" longer than the total length of the ■...
-
Page 9: Mount The Installation Brackets - Inside Mount
INSTALLATION Mount the Installation Brackets — Inside Mount Mark 2" to 4" in from each jamb. Measure and mark the underside of the dust cover, if ■ ordered. If more than two installation brackets came with your order, space additional bracket(s) ➤... - Page 10 " Tilt the headrail and insert it into the front edge of the mounting clips. Pull forward, then roll ■ the headrail back toward the rear of the blind. Push up and snap into place. Paramount Headrail ® Rear Tab...
-
Page 11: Mount The Installation Brackets - Outside Mount
Center headrail underneath mounting clips. ■ Tilt the headrail and insert it into the front edge of the mounting clip. Pull and roll the ■ headrail up toward the rear of the blind and snap into place. Paramount Headrail ® Tilt and Rear... -
Page 12: Install The Vanes
INSTALLATION If a valance is included, “snap” on a valance hanger next to each “L” bracket. ■ Center the valance in relationship to the headrail and slide it into the valance hangers. ■ Valance Hanger “L” Bracket Mounting Clip Valance (Optional) Wall Side... -
Page 13: Attach The Vertical Cord Tensioner
INSTALLATION Attach the Vertical Cord Tensioner Before doing anything, you must first slide the vertical cord tensioner to the bottom of the cord loop. Tensioner Body To release the cord tensioner, pull the mounting base down, ■ away from the tensioner body. Slide the cord tensioner down to the bottom of the cord loop. -
Page 14: Cord Adjustment-Cord And Chain Only
INSTALLATION Cord Adjustment―Cord and Chain Only note: Cord length and/or tension cannot be adjusted for PermaTilt Wand Control System. It ® is set in the factory to help ensure that the product meets cord safety standard. to reduce cord length on a Side Draw Blind: Open the blind. -
Page 15: Operation
OPERATION Split Stack Blind Operation Permatilt Wand Control ® note: Cord length and/or tension cannot be adjusted for PermaTilt Wand Control System. It ® is set in the factory to help ensure that the product meets cord safety standards. tilting. (gray arrows) When tilting your vanes use one hand ■... -
Page 16: Side Stack Blinds Operation
OPERATION PermAssure Safety Wand ® Push or pull the wand to open or close the vanes (black arrows). ■ note: Please do not bow the wand. Hold the wand at a 45˚ angle. Push or pull the wand to open or close the vanes. Twist the safety wand to open or close the vanes (gray arrows). - Page 17 OPERATION Cord and Chain operated Use the pull cords attached to the cord tensioner to open ■ or close the vanes (black arrows). Use the tassels and chains to rotate the vanes open or ■ closed (gray arrows). PermAssure Safety Wand ®...
-
Page 18: Care
CARE Removing the Headrail (If Necessary) To remove the headrail, locate the rear tab on the mounting clip. ■ Push up on the rear tab to release the headrail. ■ Paramount Headrail PermaTrak and PermAlign Headrail ® ® ® Rear Tab... -
Page 19: Child Safety
See “Attach the Vertical Cord tensioner” on page 11. this can prevent children from pulling cord loops around their necks. Hunter Douglas provides a cord tensioner installation kit with ■ instructions for attaching the cord tensioner. For the blind to operate properly, the cord tensioner must be correctly mounted and secured. - Page 20 2. Visit hunterdouglas.com for additional warranty information, frequently asked questions and access to service locations. 3. Contact Hunter Douglas at (888) 501-8364 for technical support, certain parts free of charge, for assistance in obtaining warranty service or for further explanation of our warranty.
Need help?
Do you have a question about the Paramount and is the answer not in the manual?
Questions and answers