Advertisement
Installation Instructions
WELL WATER FILTER SYSTEM
MODELS: WS1, WS4
SpringWell Water Systems has once again taken the
latest technologies in water filtration and designed a
more economical and environmentally friendly well
water system.
CUSTOMER SERVICE IS AVAILABLE MON-FRI 9AM-6PM EST
800-589-5592
WWW.SPRINGWELLWATER.COM
1
Advertisement
Table of Contents
Related Manuals for SpringWell WS1
Summary of Contents for SpringWell WS1
- Page 1 Installation Instructions WELL WATER FILTER SYSTEM MODELS: WS1, WS4 SpringWell Water Systems has once again taken the latest technologies in water filtration and designed a more economical and environmentally friendly well water system. CUSTOMER SERVICE IS AVAILABLE MON-FRI 9AM-6PM EST 800-589-5592 WWW.SPRINGWELLWATER.COM...
-
Page 2: System Contents
Well Water Filter System Setup and Installation System Contents MNPT Fittings Bypass Valve Electronic Head for Well Water Filter (Tank 1) 50’ Drain Line Power Hose Supply Clamp Well Water Filter Tank Recommended Supplies 1 Roll Plumbers Tape 1-inch (3-inch long) PVC Nipple 1-inch (24-inch Long) Corrugated Water Connectors (x2) 1-inch threaded connectors for pre-... -
Page 3: System Specifications
Well Water Filter System PLEASE READ INSTRUCTIONS FULLY PRIOR TO ATTEMPTING INSTALLATION. Be sure to follow all applicable plumbing codes. The system must be installed on a main water supply line System Specifications 10” 13” Tank Width Tank Width 54” 54”... - Page 4 Well Water Filter System Installing the Well Water Filter Electronic Head This step will require the materials listed below Tank Note: If your tank was shipped with a jacket, it can be zipped around the tank prior to or after Electronic Softener the installation is completed.
- Page 5 Well Water Filter System Installing the Well Water Filter Electronic Head 9) Fully tighten the fasteners on both 7) Install a bypass valve onto the 8) Insert the rubberized valve connections securing the bypass connections on the electronic connections into the electronic valve.
- Page 6 Well Water Filter System Installing the Tank – Part 1 This step will require the materials listed below Plumbers Tape 1-inch (3-inch long) PVC Nipple 1-Inch PVC 12) Turn off the water to the Shut Off Valve home and prep the pre-plumb. You will attach a 1-inch threaded adapter to each connection.
-
Page 7: Installing The Drain Line
Well Water Filter System 18) Connect a water connector to 19) Connect the other end of the the other side of the pre-plumb. corrugated pipe to the outgoing The side leading back into the side from the well water filter. home. - Page 8 Well Water Filter System 24) Press the barbed connector 25) Slide the hose clamp over 26) Prior to fully tightening, position the hose clamp to align on the valve onto the end of the connection and begin to as shown here. Now, fully that drain line until it is fully tighten it.
- Page 9 Well Water Filter System Powering the Tank Head This step will require the materials listed below 33) The power cord will be connected to the connection on the far left beneath the electronic tank head. Power 9v Battery Supply Well Water Filter Tank (Already Installed) 35) Lift off the cover on the 36) Locate the batter...
-
Page 10: Testing The System
Well Water Filter System Testing the System Bypass 38) While the water is still off 39) Before turning on the water to 40) Ensure that the valves on to the home, open a cold the home ensure the shut off valve the tank is set to bypass. - Page 11 Well Water Filter System Setting Well Water Head Values This step will require the materials listed below Note: The electronic tank heads must be powered and installed prior to setting the tank values. Well Water Filter Tank Mobile (Already Installed) Device 45) Look up “Legacy 47) Tap “Time of...
- Page 12 Well Water Filter System Setting Well Water Filter Values 54) Select “Advanced 55) Tap “Air Charge 53) Select the menu 56) Change the Settings.” Frequency.” icon in the upper value to 1 day. left-hand corner. 59) Tap “Rest.” 57) Tap “Backwash.” 58) Change the value to 60) Set the value to 10 min.
- Page 13 Well Water Filter System Setting Softener Values Note: The well water filter will run approx. 45 65) Tap the Menu 67) If you are ready, 66) Select minutes. You will not be “Regenerate Now.” Icon. select OK on the able to use water to the regenerate confirmation home during this time.
Need help?
Do you have a question about the WS1 and is the answer not in the manual?
Questions and answers
Why does powerhead flash time and a number